NEC Neax 2400 Imx Fusion Network System Manual

CHAPTER 4 ND-70185 (E)
Page 56
Revision 3.0
This page is for your notes. 

ND-70185 (E) CHAPTER 5
Page 57
Revision 3.0
CHAPTER 5 DATA PROGRAMMING
This chapter explains how to set Fusion Network data, using the following data categories:
 System Data
 Numbering Plan Data
 Station Data
 Fusion Link Data
Figure 5-1 shows the overall data programming procedure:
Figure 5-1   Data Programming Flow Chart
AFMU
ANPD ANPDL
STN
SSC
SSCA
OGC
OGCA
LCR
LCRS
UNIF
:
:
:
------

------
SSC
------
OGC
OGCA
LCR
LCRS
:
:   
:
TELN           Note

ASDT
System Data...

CHAPTER 5 ND-70185 (E)
Page 58
Revision 3.0
DATA PROGRAMMING
Network Data Programming Summary
1. Network Data Programming Summary
This section explains a summary of the data programming of Fusion systems.
1.1 Brand-new Fusion Network
To install the Fusion network as a brand-new system, the overall data programming procedure is as follows.
1.1.1 System Data
 Decide an NCN, and LN on the network.
 Assign System Data for each node. Use the ASYDN command for the NCN and the ASYDL com-
mand for all nodes....

ND-70185 (E) CHAPTER 5
Page 59
Revision 3.0
DATA PROGRAMMING
Network Data Programming Summary
1.2 Upgrading a CCIS Network
To install the Fusion system to an existing CCIS network, the overall programming procedure is as follows:
1.2.1 System Data
 Decide an NCN and LN on the network.
 Assign System Data for each node. Use the ASYDN command for NCN and the ASYDL command
for LN. The system data includes the size of LDM, NDM, Fusion Point Code (FPC), etc.  
Note:The data becomes effective by executing...

CHAPTER 5 ND-70185 (E)
Page 60
Revision 3.0
DATA PROGRAMMING
Network Data Programming Summary
1.3 Fusion Link Data
 Assign the Fusion Link data using the following commands:
Fusion with FCH: ACRD ➔ ACTK ➔ MBCT ➔ AFCH ➔ AFRT ➔ AFPC ➔ AC A N
Fusion w/o FCH: ACRD ➔  AFPC
Note:When the Fusion system is incorporated in an existing CCIS network, all nodes must be linked via CCIS on
the network.
If there are any nodes linked via ACIS alone, add the CCIS link before the installation of the Fusion link
(See...

ND-70185 (E) CHAPTER 5
Page 61
Revision 3.0
DATA PROGRAMMING
Network Data Programming Summary
Figure 5-3 shows how to upgrade an existing CCIS network, focusing on the Numbering Plan. The example data 
setting assumes the existing network uses this particular numbering. For more detailed information on how to assign 
Telephone Numbers, please see Assignment of Telephone Numbers.
Figure 5-3   How to Upgrade the Numbering Plan Data of an Existing CCIS Network

Before Upgrading
STN: 2000
A
CB
80

82
81...

CHAPTER 5 ND-70185 (E)
Page 62
Revision 3.0
DATA PROGRAMMING
Assignment of System Data
2. Assignment of System Data
STEP 1: ASYDL and ASYDN
Assign the number of data memory blocks for the Network Data Memory (NDM) and the Local Data
Memory (LDM). Use the ASYDN command for the NCN. Use the ASYDL command for all nodes.
Figure 5-4 shows ASYDL Indexes 513 and 514 as an example.
Figure 5-4   Assignment of Memory Block
(1) Assign the following data to all nodes.
 ASYDL, Index 513 Local Data Memory (LDM)...

ND-70185 (E) CHAPTER 5
Page 63
Revision 3.0
DATA PROGRAMMING
Assignment of System Data
STEP 2: ASYDL
Assign the self-Fusion Point Code (self-FPC) at each node. FPC ranges from 1 to 253. Use the ASY-
DL command. (Index 512 b0-b7)
 Index 512 self-Fusion Point Code
Assign a unique FPC for each node. 
Figure 5-6   Self-FPC Assignment
STEP 3: ASYDL and ASYDN
Assign other system data using the ASYDL/ASYDN command.
When Timing Start is used, assign the following data.
Index 161 b6 : 0/1=-/Timing Start using...

CHAPTER 5 ND-70185 (E)
Page 64
Revision 3.0
DATA PROGRAMMING
Assignment of System Data
Index 800
For ASYDL b0 : 0/1 = ALGNL, ALGSL on a UGN (TN) basis/-
b1 : 0/1 = ASPAL on a TN basis/-
b2 : 0/1 = ANPDL on a TN basis/-
b4 : 0/1 = AFRSL, ASTPL, AUNEL on a TN basis/-
b5 : 0/1 = ASTPL on a TN basis/-
b7 : 0/1 = AAEDL on a TN basis/-
For ASYDN b0 : 0/1 = ALGNN, ALGSN on a UGN (TN) basis/-
b1 : 0/1 = ASPAN on a TN basis/-
b2 : 0/1 = ANPDN on a TN basis/-
b4 : 0/1 = AFRSN, ASTPN on a TN basis/-
b5 : 0/1 =...

ND-70185 (E) CHAPTER 5
Page 65
Revision 3.0
DATA PROGRAMMING
Assignment of FPC and MG and UNIT into Network
3. Assignment of FPC and MG and UNIT into Network
3.1 AFMU
Assign the module accommodation data by giving Module Group Number and Unit Number on an FPC
basis. This data is necessary to allocate unique Network ID (NID) to each MG/UNIT of the whole Fusion
network nodes. Note This data can be set at the NCN only.
Note:A unique NID is assigned to each MG/UNIT, automatically by entering the AFMU data.
...