NEC Neax 2400 Imx Business Features And Specifications

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 421
Paging Transfer P-10
Service Conditions (cont’d)
8. When using this feature via the FCCS network, when PAGING ACCESS [P-1]/PAGING TRANSFER [P-
10]/RADIO PAGING [R-16] service is set to a station in the remote node or the PAGING ACCESS [P-
1]/PAGING TRANSFER [P-10]/RADIO PAGING [R-16] call is answered from the remote node via
FCCS link:
a.) the logical route number should be applied to each physical route that is provided the...

NEAX2400 IMX Business Features and Specifications
Page 422NDA-24221, Issue 3
P-11 Periodic Time Indication Tone
P-11  Periodic Time Indication Tone
General Description
This feature provides a tone every 180 seconds, if required, to the user who has made an outgoing call.
Operating Procedure
No manual operation is required.
Service Conditions
1. This feature is programmed on a per-trunk route basis using the MAINTENANCE ADMINISTRATION
TERMINAL (MAT) [M-18].
2. The PERIODIC TIME INDICATION TONE is 80 ms in...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 423
Prime Line Pickup - DtermP-13D
P-13D Prime Line Pickup - Dterm
General Description
This feature allows a Dterm user to originate or answer a call from the line designated as the Primary Line by going
off-hook. It is unnecessary to press the associated line key.
Operating Procedure
Lift the handset or press the SPEAKER key; receive dial tone.
Service Conditions
1. One Prime Line per station is allowed.
2. Unless otherwise...

NEAX2400 IMX Business Features and Specifications
Page 424NDA-24221, Issue 3
P-14D Privacy - Dterm
P-14D Privacy - Dterm
General Description
This feature allows a Dterm to establish privacy so that no station can interrupt a call via EXECUTIVE RIGHT-OF-
WAY [E-1].
Operating Procedure
1. Go off-hook; receive dial tone. Press the DO NOT DISTURB (DND) key. The associated LED will flash.
The LCD displays:
2. Dial the desired number.
3. When the call is completed, Privacy is cancelled by going on-hook....

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 425
Privacy On All Lines - DtermP-15D
P-15D  Privacy On All Lines - Dterm
General Description
This feature restricts Dterm users from pressing a busy line button and entering a conversation, which can occur with
1A2 key telephones without exclusion circuits.
Operating Procedure
No manual operation is required.
Service Conditions
1. A Dterm user cannot seize the Prime Line if it is busy.
2. LINE PRESELECTION [L-9D] is denied if the...

NEAX2400 IMX Business Features and Specifications
Page 426NDA-24221, Issue 3
P-18 Privacy Release
P-18 Privacy Release
General Description
This feature allows multiple stations (maximum 6) accommodated in the same multi-line group to override a Dterm
already engaged in communication. Also, by key operation of the Dterm already engaged in communication
(maximum of 8-party communication), overriding from other stations in the same multi-line group can be restricted.
Operating Procedure
To establish a...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 427
Privacy Release P-18
Operating Procedure (cont’d)
3. Station A lifts handset or presses SPEAKER key. The LCD displays:
4. Station C presses PRIVACY key again.
5. Station A receives ringback tone, and the LCD displays:
6. A 4-party call is established. The line appearance will flash, indicating I-USE [I-8], and the LED of
PRIVACY key will be turned off. The LCDs of the associated D
terms display:
By following the operations...

NEAX2400 IMX Business Features and Specifications
Page 428NDA-24221, Issue 3
P-18 Privacy Release
Service Conditions (cont’d)
10. When a station tries to bridge into a call and presses the line appearance, and when PRIVACY RELEASE
is not available because of the lack of an 8-party conference trunk, the LCD displays as follows, indicating
that PRIVACY RELEASE is not available:
11. PRIVACY RELEASE is not available when another station is in the process of entering a multiple-party
call (when receiving...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 429
Privacy Release P-18
Service Conditions (cont’d)
f.) While engaged in a multiple-party call, the user presses the line appearance of a busy station. 
g.) While engaged in calling a station by INTERCOM [I-9] call or Intercom Bridge call, the station
presses the line appearance of busy station. 
h.) After placing a call on CONSULTATION HOLD [H-17], the station originates a call to a station
or trunk and then presses the line...

NEAX2400 IMX Business Features and Specifications
Page 430NDA-24221, Issue 3
P-30 Priority Paging
P-30 Priority Paging
General Description
This feature allows a station or an ATTENDANT CONSOLE [A-3] to make a PRIORITY PAGING [P-30] access
when a paging call cannot normally be originated because another paging call is in progress or is waiting for an
answer.
Operating Procedure
Paging Access from a station:
1. The Paging station goes off-hook; hears dial tone. 
2. The station dials the PRIORITY PAGING...