NEC Neax 2400 Imx Business Features And Specifications

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 371
Multi Channel Recording - DAT M-48
Operating Procedure (cont’d)
Hear service set tone when # is pressed. The service set tone continues for 3 seconds.
d.) Start your recording when the service set tone is stopped.
e.) Replace the handset to finish recording.
Note:The recording length is a multiple of 2 (= 2n sec).
4. Playback by designating RT
a.) Lift a handset; receive dial tone.
b.) Dial the MULTI CHANNEL RECORDING (REPLAY)...

NEAX2400 IMX Business Features and Specifications
Page 372NDA-24221, Issue 3
M-48 Multi Channel Recording - DAT
Operating Procedure (cont’d)
e.) Replace the handset to finish playback of the recorded message.
Note:Even though the recording of a message has been finished, playback of the trunk cannot be accepted until dubbing of
the message to the remaining trunks is complete.
5. Recording of an announcement for a UCD group
a.) Lift a handset; receive dial tone.
b.) Dial the MULTI CHANNEL RECORDING...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 373
Multi Channel Recording - DAT M-48
Operating Procedure (cont’d)
b.) Dial the MULTI CHANNEL RECORDING (REPLAY) access code from the station; receive
special dial tone.
c.) Press * and enter the UCD controlling telephone number; the special dial tone is stopped.
d.) A recorded message of the designated UCD group is automatically played back.
e.) Replace the handset to finish playback of the recorded message.
Note:Even though the...

NEAX2400 IMX Business Features and Specifications
Page 374NDA-24221, Issue 3
M-48 Multi Channel Recording - DAT
Operating Procedure (cont’d)
c.) Press # and enter the message number that has been assigned in the AAST command; receive
service set tone. The service set tone continues for 3 seconds.
d.) Start your recording when the service set tone is stopped.
e.) Replace the handset to finish recording.
Note:The recording length is a multiple of 2 (= 2n sec).
8. Playback of a message for ACD
a.) Lift a...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 375
Multi Channel Recording - DAT M-48
Operating Procedure (cont’d)
d.) A recorded message of the designated Message Number for ACD is automatically played back.
e.) Replace the handset to finish playback of the recorded message.
Note:Even though the recording of a message has been finished, playback of the trunk cannot be accepted until dubbing of
the message to the remaining trunks is complete.
Service Conditions
1. Any entry of...

NEAX2400 IMX Business Features and Specifications
Page 376NDA-24221, Issue 3
M-48 Multi Channel Recording - DAT
Service Conditions (cont’d)
8. When the system encounters a busy trunk in an attempt to make a dubbing of the message to the remaining
trunks, the trunk is retried after a 16 second interval. Each trunk is attempted a maximum of 16 times. If
the final attempt is rejected because of busy, no further dubbing attempts will be made.
9. Only the portion in which a message has been recorded is played...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 377
MF Signaling - DID M-84
M-84  MF Signaling - DID
General Description
In the Associated Channel Interoffice Signaling system, this feature allows use of selective codes of Multifrequency
(MF) signals.
MF - (ANSI) codes: A total of 15 codes are available by combining two out of six frequencies.
(ANSI)
Operating Procedure
No manual operation is required.
Service Conditions
1. When using MF signaling system, Least Cost Routing...

NEAX2400 IMX Business Features and Specifications
Page 378NDA-24221, Issue 3
M-84 MF Signaling - DID
Service Conditions (cont’d)
4. Connection patterns to which MF signaling system can be applied are as follows: 
a.) Individual call origination by station
b.) Attendant-to-Attendant connection
c.) Individual call origination by Attendant
d.) Call origination by Attendant via station/trunk 
e.) MF line connection from CONSULTATION HOLD [C-17]
f.) Call transfer to MF line via Call Forwarding.
5. Connection...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 379
Message Waiting Indication - DtermM-85D
M-85D  Message Waiting Indication - Dterm
General Description
This feature allows Message Waiting (MW) information to be displayed on the middle line (24 digits) of the LCD.
Operating Procedure
No manual operation is required.
Service Conditions
1. The LCD displays the following information, when MESSAGE WAITING INDICATION - Dterm is
activated:
2. When this service is assigned to a D
term...

NEAX2400 IMX Business Features and Specifications
Page 380NDA-24221, Issue 3
M-101 MF ANI to SMDR
M-101  MF ANI to SMDR
General Description
This feature allows an office receiving ANI information by means of MF signal to output the information to the
expanded SMDR area.
Operating Procedure
No manual operation is required.
Service Conditions
1. Output conditions are same as current conditions of MF ANI. (i.e., charging information for incoming
calls is output only).
2. About the expanded output format,...