NEC Mcu 5000a Multipoint Control Unit Equipment Manual

NECA 340-414-210 Revision 2.0 Page 3 of 4
MCU 5000A Multipoint Control Unit GSD-010
Table 2: LED Functions for VDSW Unit
LED NAME COMPONENTS FUNCTION LED COLOR
LED1 CONF AAMBER
LED2 CONF BAMBER
LED3-1
~
LED3-4
LED4-1
~
LED4-4JOIN
RC1~RC8Indicates participants’ conference room.   GREEN
LED5-1
~
LED5-4OPE
(RC1 ~ RC8) Indicates the operator. GREEN
LED6-1
~
LED6-4VIDEO
(RC1 ~ RC4) Indicates the broadcast sending terminal.GREEN
LED7-1
~
LED7-4LSD1
RC1 ~ RC4 Indicates the LSD broadcast sending terminal.GREEN...

Page 4 of 4 NECA 340-414-210 Revision 2.0
GSD-010 MCU 5000A Multipoint Control Unit
This page is for your notes. 

NECA 340-414-220
ISSUE 2
DOI-G05185
PART OF STOCK # 0293922
SYSTEM PARAMETERS MANUAL
SEPTEMBER, 1998
NEC America, Inc.
MCU 5000A MULTIPOINT 
CONTROL UNIT 

LIABILITY DISCLAIMER
NEC America, Inc. reserves the right to change the specifications,
functions, or features, at any time, without notice.
NEC America, Inc. has prepared this document for use by its em-
ployees and customers. The information contained herein is the
property of NEC America, Inc. and shall not be reproduced without
prior written approval from NEC America, Inc.  
Copyright 1998
NEC America, Inc.
Printed in USA 

NECA 340-414-220 Revision 2.0Page i
MCU 5000A Multipoint Control Unit Table of Contents
Table of Contents
INTRODUCTION .................................................................................................  INT-001
CONSOLE RELATED
CONSOLE INITIAL MESSAGE SETTING ....................................................  SPR-001
CONSOLE COMMAND GENERATION SETTING........................................  SPR-002
CONSOLE COMMUNICATION PARAMETER SETTING .............................  SPR-003
CONSOLE...

Page iiNECA 340-414-220 Revision 2.0
Table of Contents MCU 5000A Multipoint Control Unit
TERMINAL CAPABILITY RELATED
AUDIO CAPABILITY SETTING ....................................................................  SPR-027
TRANSFER RATE CAPABILITY SETTING..................................................  SPR-028
VIDEO CAPABILITY SETTING ....................................................................  SPR-029
LOW SPEED DATA (LSD) CAPABILITY SETTING .....................................  SPR-030
HIGH...

NECA 340-414-220 Revision 2.0Page iii
MCU 5000A Multipoint Control Unit Table of Contents
TERMINAL MODE RELATED
AUDIO MODE SETTING ...............................................................................  SPR-039
TRANSFER RATE MODE SETTING ............................................................  SPR-040
VIDEO MODE SETTING ...............................................................................  SPR-041
LOW SPEED DATA (LSD) MODE SETTING ...................................................

Page ivNECA 340-414-220 Revision 2.0
Table of Contents MCU 5000A Multipoint Control Unit
This page is for your notes. 

NECA 340-414-220 Revision 2.0 Page 1 of 8
MCU 5000A Multipoint Control Unit INT-001
INTRODUCTION
1. GENERAL 1.01This document describes the information of system parameters for setting 
the 
Multipoint Control Unit 5000A (MCU 5000A).
2. OVERVIEW 2.01The MCU 5000A system parameters are for use in setting the operating 
environment for the MCU 5000A.  After installing the MCU 5000A, the system 
parameters must be set conforming to user’s system operations by this manual. 
2.02The system parameters are...

Page 2 of 8 NECA 340-414-220 Revision 2.0
INT-001 MCU 5000A Multipoint Control Unit
How to verify system parameters
After setting system parameters, verification of their correctness or details can be 
performed by entering RSPR commands from the console. 
RSPR *** [return] 
*** : system parameter address (hexadecimal values 0 to 3FF).
If omitted, all the parameters will be displayed.
If L is entered, the parameters for addresses 000 to 0FF will be displayed.
If H is entered, the parameters for addresses...