NEC Mcu 5000a Multipoint Control Unit Equipment Manual
Here you can view all the pages of manual NEC Mcu 5000a Multipoint Control Unit Equipment Manual. The NEC manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 141
NECA 340-414-210 Revision 2.0 Page 3 of 4 MCU 5000A Multipoint Control Unit INP-009 Figure 3: LIF (CH1 to CH16) Cable Connections 8 151 9
Page 142
Page 4 of 4 NECA 340-414-210 Revision 2.0 INP-009 MCU 5000A Multipoint Control Unit This page is for your notes.
Page 143
NECA 340-414-210 Revision 2.0 Page 1 of 2 MCU 5000A Multipoint Control Unit INP-011 POWER CORD CONNECTION GENERAL: This cord is used to supply power to MCU. This procedure provides the instruction. APPARATUS: None SUPPORT DATA: None Figure 1: Power Cord Connection STEP PROCEDURES 1Set power switch of MCU 5000A to the OFF position. 2 Connect the power cord to the power terminal at rear side of MCU 5000A. (See Fig. 1 and Ta b l e 1.) 3 End of procedure. 48.4 inches (1.23 meters)
Page 144
Page 2 of 2 NECA 340-414-210 Revision 2.0 INP-011 MCU 5000A Multipoint Control Unit Figure 2: AC IN SIGNAL ASSIGNMENT Table 1: AC IN Connector Pin Assignment PIN NO. SIGNAL NAME I/O REMARKS 1 AC IN IN AC 117 V input 2 AC IN IN AC 117 V input 3 FG - Frame ground 12 3
Page 145
NECA 340-4 14- 21 0 Revisio n 2.0 Page 1 o f 4 MCU 5000A Multipoint Control U nit INP-012 STA RT-UP OF MCU CONSOLE
Page 146
Page 2 o f 4 NECA 340 -41 4-2 10 Revisi on 2.0 INP-012 MCU 5000A Mult ipoint Con trol Unit STEP PROCEDURES
Page 147
NECA 340-414-210 Revision 2.0 Page 3 of 4 MCU 5000A Multipoint Control Unit INP-012 Figure 1: Connection of MCU Console to MCU 5000A Note: x.xx indicates version No. of memory card. Figure 2: Opening Message MCU REAR TERMINAL ARRANGEMENT RS-232C AC IN CH1CH5 CH1 CH13 CH9 CH5CH1 CH2CH6 CH2 CH14 CH10 CH6CH2 CH7 CH3 CH3 CH15 CH11 CH7 CH3 CH4 CH8 CH4 CH16 CH12 CH8 CH4 RS-232CHSD IFL IF RS-232C MCU CONSOLE (REVERSE) PORT Note: The channel 4 (CH4) at RS-232C interface port does not support...
Page 148
Page 4 of 4 NECA 340-414-210 Revision 2.0 INP-012 MCU 5000A Multipoint Control Unit Figure 3: RS-232C (CH1 to CH4) Connector Pin Assignment Table 1: RS-232C (CH1 TO CH4) SIGNAL ASSIGNMENT PIN NO. SIGNAL NAME I/O REMARKS PIN NO. SIGNAL NAME I/O REMARKS 1 FG - Frame Ground 14 - 2 SD OUT Send Data15 ST2IN Send Signal Element Timing 3 RD IN Receive Data 16 - 4 RS OUT Request Send17 RTOUT Receive Signal Element Timing 5 CS IN Capacity Send 18 - 6 DR IN Data Set Ready 19 - 7SG - Signal ground20 EROUT...
Page 149
NECA 340-414-210 Revision 2.0 Page 1 of 2 MCU 5000A Multipoint Control Unit INP-013 SETTING FOR CODEC GENERAL: This procedure provides instruction for parameter setting about CODEC (VisuaLink 5000) using for TV conference terminal. APPARATUS: None SUPPORT DATA: VL 5000 Manual STEP PROCEDURE 1 The functional parameter required for VL 5000 are registered in the non-volatile memory. At system starting, functional parameters which are registered in the non-volatile memory are automatically loaded,...
Page 150
Page 2 of 2 NECA 340-414-210 Revision 2.0 INP-013 MCU 5000A Multipoint Control Unit This page is for your notes.