Mitel Sx 50 Dpabx Instructions Guide

Customer Data Entry (CDE) 
Register 4 
a bcdefghij 
4 1 1 1 1 0 0 0 0 0 
b: Call Forward - Follow Me 
0 = Disable all Call Forwarding 
1 = Allow forwarding of trunks or extensions to internal numbers only 
2 = Allow forwarding of extensions only to internal or external numbers 
3 = Allow forwarding of trunks or extensions to internal or external numbers 
c: Call Forward - Busy 
0 = Disable all Call Forwarding 
1 = Allow forwarding of trunks or extensions to internal numbers only 
2 = Allow forwarding of...

.,. 
Yy 
Customer Data Entry Registers 
COMMANDS 121 - 129 COS 1 - COS 9 Programming (Cont’d) 
Register 5 
a b c d e f g hi j k 
5 1 1 1 1 1 1 1 1 ; 0 
b: Abbreviated Dial Numbers 10 - 19 or 100 - 199 
0 = Disable 
1 = Enable . 
c: Abbreviated Dial Numbers 20 - 29 or 200 - 299 
0 = Disable 
1 = Enable 
d: Abbreviated Dial Numbers 30 - 39 or 300 - 399 
0 = Disable 
1 = Enable 
e: Abbreviated Dial Numbers 40 - 49 or 400 - 499 
0 = Disable 
1 = Enable 
f: Abbreviated Dial Numbers 50 - 59 or 500 - 599 
0 =...

Customer Data Entry (CDE) 
Register 6 
b: 
c: NOT USED 
Outgoing Access To E&M Tie Trunks 
0 = Disable 
1 = Enable 
d: Outgoing Access To CO Trunks 
0 = Disable 
1 = Enable 
Register 7 
b: 
c: 
d: 
e: 
f: 
9: 
210 4-22 
SUPERSET 4ISUPERSET 420 Message Programming 
0 = Disable 
1 = Enable 
Account Code Entry 
0 = Not allowed 
1 = Optional 
2 = Required for Toll Calls Only 
3 = Required for all Calls (Toll & Non-Toll) 
Auxiliary Attendant Position 
0 = Disable 
1 = Enable 
Directed Call Pickup 
0 = Disable...

yo 
Customer Data Entry Registers 
h: Lockout Alarm 
0 = Disable 
1 = Enable 
Register 8 
a b c d e f g 
8 11 10 0 0 
b: Extension Camp-on 
0 = Disable 
1 = Enable 
c: CO Trunk Camp-on 
0 = Disable 
1 = Enable 
d: Inward Dial Trunk Camp-on 
0 = Disable 
1 = Enable 
e: DID Restriction 
0 = Disable 
1 = Enable 
Trunk Group Programming 
4.5 The Trunk Group Programming commands set parameters and feature options that 
apply only to the trunks in the Trunk Group. In all cases there are default values; the...

Customer Data Entry (CDE) 
Identified Trunk Group: After any trunk in an identified trunk group has been seized 
outgoing, it outpulses the trunk group access code before the digits dialed at the calling 
telephone. This option is applicable to some types of networking. 
Wait for Dial Tone: Outpulsing of the dialed digits begins when dial tone is received 
or 5 seconds after trunk seizure, whichever is sooner. The other options are: 
l dial after a programmed delay of up to 5 seconds, 
l check for dial...

cau 
Customer Data Entry Registers 
d: Overflow Trunk Group 
0 = Disable 
1 - 6 = Trunk Group Number 
e: Identified Trunk Group 
0 = Disable 
1 = Enable 
f - i: Trunk Group Access Code 
Defaults: 
Cmd151 =9,Cmd152=8, 
Cmd153=78,Cmd154=79 
Cmd 155 = blank, Cmd 156 = blank 
Register 2 
a 
bcdefghijk 
20020000000 
b: Wait For Dial Tone 
0 = No wait, outpulse after delay 
1 = Wait up to 5 seconds, then outpulse anyway 
2 = Check for dial tone every 5 seconds 
3 = Unlimited wait with detection by user 
c:...

Customer Data Entry (CDE) 
h: Simulate CO Dial Tone 
0 = Disable 
1 = Enable 
. . 
I. Trunk Group SMDR Enable 
0 = Disable 
1 = Enable 
. . 
J- Trunk Group Last Number Redial 
0 = Disable 
1 = Enable 
k: Trunk Group Manual E&M Trunk 
0 = Disable 
1 = Enable 
Register 3 
b: Message Registration 
0 = Disable 
1 = Enable 
C:. Count Additional Message Units 
0 = Disable 
1 = Enable 
2 = Enable, Insert Pseudo Message Unit every 6 Seconds 
3 = Enable, Insert Pseudo Message Unit every 60 Seconds 
d,e: Initial...

au 
Customer Data Entry Registers 
c: Behind PABX Operation 
0 = Disable 
1 = Enable, Flash is Loop Disconnect 
2 = Enable, Flash is Ring Ground 
d: 
Behind PBX Recall Signal Duration 
0 = 500 ms 
1 = 750 ms 
e: Credit Card Calling Operation 
0 = Disable 
1 = Enable 
User Programming Access 
4.6 The User Programming Access registers determine which command registers may 
be modified by the system user entering CDE with the User Security Code. They do 
not affect installer access via the System Security...

Customer Data Entry (CDE) 
0 = Disable 
1 = Enable 
Register 2 
a bcdefgh - 
2 0 0 0 0 0 0 0 
b: 
c: 
d: 
e: 
f: 
9: 
h: Commands 361 --, 366, Extension Hunting _ 
0 = Disable 
1 = Enable 
Command 381, Ring Group Programming 
0 = Disable 
1 = Enable 
Commands 
401 --z 480, SUPERSET Telephone Programming 
0 = Disable 
1 = Enable 
Commands 501 - 580, Trunk Programming 
0 = Disable 
1 = Enable 
Commands 151 -+ 156, Trunk Group Programming 
0 = Disable 
1 = Enable 
Commands 700 --, 752, ARS Data Table...

Customer Data Entry Registers 
d: Command 191, User Security Code Programming 
0 = Disable 
1 = Enable 
e: Command 193, DISA Access Code Programming 
0 = Disable 
1 = Enable 
f: Command 192, RMATS Security Code Programming 
0 = Disable 
Note: Fields c and fare always disabled and cannot be modified- 
9104-091-210-NA Issue 5 
Revision 0 210 4-29