Mitel Sx 50 Dpabx Instructions Guide

Shipping, Receiving and Installation 
r . 
‘i 
. 
. . ..- (6 AWG) 
200 5-22 
Figure 5-13(a) System Cabling 
Revision 0 9104-091-200-NA Issue 5  

Installation Procedures 
Figure 5-13(b) System Cabling 
9104-091-200-NA Issue 5 
Revision 0 200 5-23  

Shipping, Receiving and Installation 
. 
CARD 
HANDLE 
CABLE 
TIE 
DD0049 
Figure 5-l 3(c) System Cabling 
9-WIRE JACKS (CUSTOMER-PROVIDED) 
CABLE PROVIDED WITH 
CONTROL CARD 
ATENDANT CONSOLE 
MDFIPLANT WIRING 
S-WIRE CABLE (CUSTOMER-PROVIDED) 
1, THE AlTENDANT CONSOLE CAN BE PLACED A MAXIMUM OF 200m FROM THE CONTROL CARD. 
2. CONSOLE WIRING PAIRS (14.2-5, S-4) MUST BE KEPT AS PAIRS IN PLANT WIRING. 
DD0055 
200 5-24 
Figure 5-14 Remote Attendant Console Cable Installation 
Revision 0 9104-091-200-NA...

Installation Procedures 
Chart 5-6 Attendant Console Installation 
Step Action Comments 
1. Install Cable at Attendant Console. Refer to Figure 5-l 5, Cable Installa- 
l Insert the Attendant Console Cable into the tion on the Attendant Console. 
socket. 
Note: the Attendant Console can be 
placed up to 200 m (218 yd.) from the SX-50 
System. 
2. Install the Handset. 
l Plug one end of the Handset Cord into the 
Handset. Plug the other end of the Handset 
Cord into one of the two sockets on the left-...

Shipping, Receiving and Installation 
- Chart 5-7 Miscellaneous Equipment installation 
Step Action Comments 
1. Install the Customer-provided Night Bells Refer to Figure 5-16, Night Bell Con- 
Equipment. nections. 
l Connect the leads to the terminal block on the 
Control Card. 
l For ac Night Bells with a capacitor, terminate 
bell circuit between B and C. Connect termi- 
nals A and D together on the terminal block. 
l For ac Night Bells without a capacitor, termi- 
nate bell circuit between B and C....

Installation Procedures 
TERMINAL BLOCK 
CROSS 
CONNECT 
CONTROL CARD 
FRAME 
AC NIGHT BELLS (WITH INTERNAL CAPACITOR) NIGH? 
BELL 
NIGHT 
BELL 
TERMINAL BLOCK 
 CROSS 
CONNECT 
CONTROL CARD 
FRAME 
AC NIGHT BELLS (WITHOUT INTERNAL CAPACITOR) 
 “p FRAME  CROSS 
CONNECT 
TERMINA; BLOCK 
 RELAYA [ ” 
REIAY B 
J.QURN C(NC’ 
NGING D(NC 
CONTROL CARD 
DC NIGHT BELLS 
DD0056 
Figure 5-16 Night Bell Connections 
9104-091-200-NA Issue 5 
Revision 0 200 5-27  

. 
Shipping, Receiving and Installation 
Table 5-3 Printer Port Pin Assignments 
Pin 
1 Source Assignment 
Not Used 
I I 2 Printer 1 RxD (Receive Data) 
-3 SC-50 System TxD (Transmit Data) 
4 Printer RTS (Request to Send) 
- 
5 SX-50 System CTS (Clear to Send) 
I 6 I 1 Not Used 
7 Common GND (Ground) 
8* 25 Not Used 
Table 5-4 Control Card Status Switch Functions 
1 Switch Number 1 Function 
I 1 
OPEN - Programming: Security Code Required 
CLOSED - Programming: No Security Code Required 
I 
2 
OPEN -...

Installation Procedures 
MDF 
MUSIC ON HOLD/PAGER MODULE 
----- 
----- 
NOTES: 
1. PIN DESIGNATIONS SHOW MOH/PAGER MODULE IN FIRST POSITION OF UNIVERSAL CARD 
2. THE SXS08 SYSTEM SUPPORTS ONE MOHlPAGER MODULE. 
I CONTROL CARD 2 
I 
I 
I 
I. 
I 
I 
I 
I 
I 
I 
I 
TERMINAL 
BLOCK 4 
I 
 
* 
3 PAGER 
DDOO57 
Figure 5-17 Music/Paging Connections 
9104-091-200-NA Issue 5 
Revision 0 200 5-29  

Shipping, Receiving and Installation 
- Chart 5-8 System Power-Up and Load Default Data 
Step Action Comments 
1. Ensure the Power Supply is OFF. 
2. 
Plug in the ac Power Cord. 
3. Set all the Control Card Status Switches to 
Refer to Table 5-4, Control Card Sta- 
open. tus Switch Functions. 
4. 
Install Attendant Console. (If required). 
5. 
Switch Power Supply ON. 
6. Load Default 
Data.Within 10 seconds after ? ap- If this does not occur, refer to Section 
pears on the Control Card LED (the Attendant...

i- Installation Procedures 
moo37 
Figure 5-18 Cover Installation 
9104-091-200-NA Issue 5 
Revision 0 
200 5-31