Mitel Sx-2000 Integrated Communications System Control Sheet Manual

							, : 
. . 
m IA 
SX-2000 S ICS Commissioning 
(A)UPPERSHELF-SHELF2 
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 16 19 20 
* * * * * * 
E 
is 
PERIPHERALINTERFACE CARDS 2 
VJAXIMUM OF 12) 8 
k-5 
B 
(S)LObVERSHELF-SHELF1 
1 2 3 4 5 6 7 6 9 10 11 12 13 14 15 16 17 16 19 20 
* * * * * * 
I I I I I I I 
PERIPHERALINTERFACE CARDS 
(MAXIMUM OF 12) 
NOTES: 1. Theminbnum~~musthavethecardsindicatedbyqnstalledhslotsssshown. 
2. Digital Se&e Unih may be sny of thefdlawing: 
Cmference card, DSI or CEPT Fumattec Cards, DTRX o( Ccmms Pmc’r cards. 
3. Control RAM II card notrequired wilh Main Catdler II card. 
Figure 4-l SX-2000s Circuit Card Locations 
9125-060-204-NA Issue 1 Revision 0 204 4-5  
						

							Commissionina 
load Commissioning Software 
4.2 The following chart details the steps required to install commissioning software on 
the SX-2000 S system. 
Chart 4-3 Load Commissioning Software On Plane A 
step Action Comments 
1. Remove the ‘Write Protect” tab on the Commissioning 
The diskette/tape and the HDMs 
floppy diskette. are protected from corruption 
since by default when tests are 
If the commissioning software is stored on a cartridge run on these devices only 
tape, then ensure that the RECORD tab is in the designated test pages are 
RECORD position, 
accessed by them. 
2. Insert the commissioning floppy/tape in the external If the external storage device is an 
storage device. FDU II, turn the latch to lock the 
diskette in place. 
3. Press and hold the PANEL ENABLE button on the The Main Controller executes a 
Maintenance Panel, and press the PLANE A LOAD series of preloading tests. Refer to 
button. Practice 9125-060-353-NA, 
General Maintenance Information, 
Note: DO NOT remove the diskette/tape from the for a description of the processor 
external storage device. Both Main Controller card diagnostic tests. If errors 
cards (on the redundant SX-2000 S system) occur, loading halts and an error 
are trying to access the external storage code is returned on the Main 
device. Controller numeric display. If an 
error should occur, repeat step 3. 
If the second loading attempt fails, 
refer to Practice 
9125-060-35O-NA, 
Troubleshooting Procedures. 
4. Check that the Maintenance Terminal returns the 
following message: 
SX-2000 (small) COMMISSIONING IN PROGRESS 
(Date and name of load is output) 
TIME: 0O:OO:OO 
CONFIGURATION REPORT NOW BEING 
GENERATED 
5. 
Check that after a delay, the system generates a The length of the delay is 
configuration report for all installed cards. proportional to the number of 
cabinets in the system. No output 
appears at the terminal until all 
cards are configured. 
Refer to Appendix A., Table A2-1, 
for an example of a configuration 
report. 
Page 1 of 2 
264 4-6 Revision 0 912!!&60-204-NA Issue 1  
						

							m IA 
SX-2000 S ICS Commissioning 
Chart 4-3 Load Commissioning Software On Plane A 
(continued) 
and reinsert the incorrectly 
configured card. Enter the 
CONFIG command to generate a 
new report, If the card still does 
ONFIGURATION REPORT 
** ENTER  TO CONTINUE * 
Press the space bar on the terminal. 
returns the following message: 
TIME 0O:nn:nn (where ‘n’ is a digit, O-9) 
a bus error is likely to occur. The 
system returns a bus error 
indicating that the active Main Control is ready for 
Any commands entered at the Maintenance Terminal 
after this point require the Maintenance Terminal 
RETURN key be pressed. Any command entered 
hereafter is assumed to be terminated this way. message on the Maintenance 
Terminal, including the address at 
which the fault occurred. Note the 
address and refer to Practice 
9125-06%352-NA, Maintenance 
Messages, to determine which 
RAM card is faulty. Replace the 
riate card and restart this 
from step 3 before 
completed, check that the display returns to a flashing 
“11” indication. 
10. Enter the following command: Enables the printing of error tables 
for each test executed, in long 
EPRINTL form (detailed tables). See 
Appendix A., Table A2-6, for an 
example. 
11. Go to Chart 4-4 for commissioning tests. 
Page 2 of 2 
9125-060-204-NA Issue 1 
Revision 0 
204 4-7  
						

							Commissioning 
Control and Peripheral Card Tests 
4.3 The following chart details the steps required to perform Control and Peripheral 
Interface card tests on Plane A of an SX-2000 S system. 
Chart 4-4 SX-2000 S ICS Plane A Control and Peripheral Interface Card Tests 
SW Actlon 
Comments 
1. 
Enter the following commands to enable testing of the 
mass storage devices: 
EXTERNAL ON 
HDM ON Enable external device testing; 
Enable HDM testing; 
MHDM ON 
Enable mate HDM testing. 
EXTERNAL ON test is not possible 
if the write protect tab is in place on 
the diskette or if the RECORD tab 
is not in the RECORD position on 
the cartridge tape. 
By default, testing of mass storage devices is 
disabled. Any of these commands can be 
individually entered to enable 
testing of a specific mass storage 
device. 
Testing of mass storage devices is 
disabled by issuing one of the 
following commands, as 
appropriate: 
EXTERNAL OFF 
HDM OFF 
MHDM OFF 
2. 
Enable testing of the Main and Peripheral Control 
Subsystems by entering: 
STEST 
ETEST l-20 This enables testing of all cards in 
slots 1 through 20 on the current 
shelf, both Control cards and PICs. 
The mass storage subsystem tests 
are run when the slot 20 tests are 
run. 
3. 
Set the number of test passes to 1 by entering the 
Optional: the default number of 
following command: 
passes is 1. 
PASS 1 
4. 
Start the test by entering: If the external device is a CTU the 
TEST test will take approximately 30 
If a slot passes the tests, the system responds with: minutes to complete. 
0O:OO:OO 000 TEST COMPLETE - NO ERRORS ON Tests are executed from the lowest 
SLOT NUMBER xx (shelf number) (cabinet number) to the highest slot. 
(test number) (pass number) If errors are detected, error 
and proceeds to test the next slot. messages are returned. Refer to 
the Appendices for the messages 
which may be encountered. 
Page 1 of 3 
204 4-6 
Revision 0 9125-060-204-NA Issue 1  
						

							m Id 
SX-2000 S ICS Commissioning 
Chart 4-4 SX-2000 S ICS Plane A Control and Peripheral Interface Card Tests 
(continued) 
rrors on an 
message 1s returne 
external device appear against the 
152 CARD NOT DETECTED - NO TEST RUN 17 Main Controller test. 
(shelf number) (cabinet number) (test number) (pass 
If a CR-II or CSM-II card or a PIC 
fails a test, reinsert the failed card, 
and rerun the test on that slot by 
issuing the following command: 
153 NO TEST AVAILABLE FOR THIS SLOT TEST (slot number) 
These messages may be disregarded, since there is If the card in question fails again, 
no testing available for any DSUs using 
Commissioning software. 
If the Main Controller must be 
replaced, the system must be 
restarted as described in 
The system returns the following prompt, indicating 
that Plane B is ready for testing: 
If a Peripheral Switch Controller card is installed in 
Shelf 2 of the Control Cabinet, enter the following 
command to test it: The Plane B Peripheral Switch 
Controller Card is only installed on 
fully redundant systems. 
If full redundancy is not provided 
If the card passes the test, the system returns the on the system being 
following message: commissioned, go to step 7. 
0O:OO:OO 000 TEST COMPLETE - NO ERRORS ON Accessing Shelf 2 as a peripheral 
SLOT NUMBER 16 01 02 (test number) 
(pass shelf does not allow testing of the 
other control cards (slots 17-20). 
Suppress all previous testing. 
Enable testing of slots 1 - 12. 
Test cards in slots 1 - 12. 
to the next slot. 
messages are returned. Reinsert 
the card and test again. Replace 
Paae 2 of 3 
9125-060-204-NA 
Issue 1 Revision 0 
204 4-9  
						

							Commissioning 
Chart 4-4 SX-2000 S ICS Plane A Control and Peripheral Interface Card Tests 
(continued) 
SW Action Comments 
a. If one or more Peripheral Cabinets is provided then To enable testing in another 
repeat steps 6 and 7 for each shelf in each peripheral cabinet, enter the command: 
cabinet. 
SHELF (cabinet number), 
(shelf number) 
9. 
Type “SHELF” to return to the  prompt. 
Test all of the circuit switch links from the main control 
to all of the peripheral shelves by entering the 
following command: 
TEST CIR LINKS 
10. If Main Control redundancy is provided, go to 
Chart 45. If the system is a non-redundant 
configuration, go to Chart 4-6. 
Page 3 of 3 
load And Test Plane B And Mate links 
4.4 Loading and testing of Plane B and its associated mate links on the SX-2000s 
system is performed as described in the following chart. This procedure does not 
apply to the not-t-redundant SX-2000s system since it only has one plane (Plane A). 
! Chart 4-5 SX-2000 S ICS Load and Test Plane B and Control Mate Links 
step 
Action Comments 
1. On completion of the self-test, disconnect the 
Maintenance Terminal from the TERMINAL A port on 
the Maintenance Connector’s panel and connect it to 
the TERMINAL 8 port. 
2. Press and hold the PANEL ENABLE button on the 
Maintenance Panel. Press the ACTIVITY SWITCH 
button. Plane B is now active, and Plane A 
is inactive. 
3. 
Hold down the PANEL ENABLE button and press the Commissioning software is loaded 
PLANE B LOAD button. onto the Plane B Main Controller 
from the external device. 
- 
Page 
1 of 3 
204 4-10 Revision 0 
9125-060-204-NA Issue 1  
						

							m IA 
SX-2000 S ICS Commissioning 
Chart 4-5 SX-ZUOU S ICS Load and Test Plane B and Control Mate Links 
(continued) 
owing message: 
SX-2000 (small) COMMISSIONING IN PROGRESS 
(Date and name of load is output) 
TIME: 0O:OO:OO 
CONFIGURATION REPORT NOW BEING 
ETEST l-20 Suppress all previous testing. 
MATE LINK ON test, Commissioning must be 
running and a maintenance 
terminal must be connected to both 
To disable the test, issue the command: 
MATE LINK OFF 
10. Test the Peripheral Mate Links in the first cabinet by It is not necessary to have both 
issuing the following commands: main control planes since both 
peripheral processors are 
PERMATE LINK ON controlled by the active main 
TEST 16 processor. 
11. Enter the following command to enable testing of 
Shelf 2 of the Control Cabinet: 
SHELF 1,2 
The system responds with:  
Page 2 of 3 
9125-060-204-NA Issue 1 Revision 0 
204 4-11  
						

							Commissioning 
Chart 4-5 SX-2000 S ICS Load and Test Plane B and Control Mate Links 
(continued) 
Step Action Comments 
12. Test the Plane B Peripheral Switch Controller card by 
entering the following command: 
TEST 16 
If the card passes the test, the system returns the 
following message: 
0O:OO:OO 000 TEST COMPLETE - NO ERRORS ON 
SLOT NUMBER 16 01 02 (test number) (pass 
number) 
and then returns the peripheral prompt. 
13. Begin testing of PlCs on Shelf 2 by entering: 
STEST Suppress all previous testing. 
ETEST 1-12 Enable testing of slots 1 - 12. 
TEST Test cards in slots 1 - 12. 
If the card passes the test, the system returns the 
following message: 
0O:OO:OO 000 TEST COMPLETE - NO ERRORS ON 
SLOT NUMBER xx (cabinet number) (shelf number) If errors are detected, error 
(test number) (pass number) messages are returned. Reinsert 
the card and test again. Replace 
and the system proceeds to the next slot. any cards which fail the second 
test. 
14. If one or more peripheral cabinets is provided, then 
repeat steps 11 to 13 for each shelf in each peripheral 
cabinet. 
15. After all peripheral cabinets are tested, disable the 
peripheral mate link tests, by issuing the command: 
PERMATE LINK OFF 
16. Go to Chart 4-6. 
Page 3 of 3 
204 4-12 Revision 0 9125-060-204-NA Issue 1  
						

							m IA 
SX-2000 S ICS Commissioning 
Maintenance Panel Commissioning 
4.5 The following chart provides details on commissioning a maintenance panel on an 
SX-2000 S system. 
Chart 4-6 SX-2000 S Maintenance Panel Commissioning 
TIVE plane on the Maintenance Connector 
The system delivers the following message: 
SYS ID MODULE PRESENT 
Visual led test: Minor, Major, Criiical, All ON, OFF 
Perform the following visual checks: 
l Minor ALARM LED comes on and goes off. 
0 Major ALARM LED comes on and goes off. 
l Critical ALARM LED comes on and goes off. fro:Plane A in non-redundant 
mber) (cabinet number) 
SHOW PANEL 
TERMINAL port on the Maintenance Connector panel 
on the bottom rear of the Control Cabinet. Repeat 
steps 2 through 4. 
Page 1 of 2 
9125-060-204-NA Issue 1 Revision 0 204 4-13  
						

							Commissioning 
Chart 4-6 SX-2000 S Maintenance Panel Commissioning 
(continued) 
Step I Action Comments 
I 
6. Remove the commissioning diskette/tape from the 
external device. 
7;, Hardware commissioning is now complete. Refer to 
Practice 9121-06&200, Installation, for software 
installation. 
Page 2 of 2 I 
204 4-14 Revision 0 912!3-060-204-NA Issue 1