Mitel Sx-2000 Integrated Communications System Control Sheet Manual

							SX-2000 SG ICS Commissioning 
load and Test Plane B and Mate links 
Loading and testing of Plane B and its associated mate links on the SX-2000 SG 
system is performed as described in the following chart. 
Chart 54 Load and Test Plane B and Control Mate Links 
Maintenance Terminal from the TERMINAL A port on 
ector panel and connect it to the 
press the PLANE B LOAD SOURCE button. 
following message: The SX-2000 SG system has 
the following load sources: 
LOAD SOURCE 1 -hard disk 
LOAD SOURCE 2 -flo 
SX-2000 COMMISSIONING IN PROGRESS 
(Date and name of load is output) 
TIME: 0O:OO:OO 
CONFIGURATION REPORT NOW BEING 
The configuration report is followed by the prompt: 
ENTER SPACE TO CONFIG PERIPHERALS,  TO 
RETURN TO COMMAND MODE> 
Press the terminal space bar. 
The system responds with: 
Refer to Appendix A., 
PERIPHERAL SWITCH HARDWARE Table A2-3, for an example of a 
CONFIGURATION IN PROGRESS peripheral and DSU 
configuration report. 
Page 1 of 2 
9125-060-204-NA Issue 1 Revision 0 204 5-11  
						

							Commissioning 
Chart 5-5 Load and Test Plane B and Control Mate Links 
(continued) 
Step Action Comments 
6. Enable long-form printing of messages by issuing the See Appendix A., Table A2-8, for 
EPRINTL command at Maintenance Terminal when the 
 prompt appears. an example of the EPRINTL 
command output. 
7. Test Plane B Control Cards by issuing the following 
commands: 
STEST 
ETEST 1-25 
TEST Suppress all previous testing. 
Enable testing of slots 1 - 25. 
Test cards in enabled slots. 
a. If errors occur during testing of any slot, remove and 
reinsert the card and retest. Replace any cards which 
fail the second test. 
9. Test the main control mate links by issuing the following To run the main control mate link 
commands on both planes simultaneously: test, Commissioning must be 
running and a maintenance 
MATE ON terminal must be connected to 
TEST 8 both planes at once. 
To disable the test, issue the command: 
MATE OFF 
10. Test the Peripheral Mate Links in the first cabinet by It is not necessary to have both 
issuing the following commands: main control planes since both 
peripheral processors are 
SHELF 1,3 controlled by the active main 
PERMATE ON processor. 
TEST 29 
11. If one or more peripheral cabinets is provided, then 
repeat step 10 for each shelf pair in each peripheral 
cabinet. 
12. After all peripheral cabinets have been tested, disable 
the peripheral mate link test by issuing the command: 
PERMATE OFF 
13. Type “SHELF” to obtain “” prompt. 
14. Go to Chart 5-6. 
Page 2 of 2 
204 5-12 
Revision 0 9125-060-204-NA Issue 1  
						

							SX-2000 SG ICS Commissioning 
Maintenance Unit Commissioning 
5.6 Commissioning of the maintenance unit is performed on the SX-2000 SG system as 
described in the following chart, 
Note: In the following procedure, the terms ‘unit’ and ‘panel’ are interchangeable. 
Chart 5-6 SX-2000 SG Maintenance Unit Commissioning 
Connector panel on the Control Cabinet. Enzire that 
the printer is on-line and ready to print. should be set for: 
- 8 data biis 
Maintenance Unit commissioning software is loaded 
from the commissioning diskette. Once loaded, the 
-the printer prints 20 lines of data. 
-the MINOR ALARM LED turns ON, then OFF 
-the MAJOR ALARM LED turns ON, then OFF. 
-the REMOTE ALARM LED turns ON, then OFF. 
-the following test message is scrolled across the 
Maintenance Unit display: 
-the Power Fail Transfer relays are operated. 
-the fan speed is set to low, then high for each An audible click is heard as each 
-when the tests are complete, the following 
message appears on the Maintenance Terminal: 
TEST COMPLETE, NO ERRORS ON SLOT 
NUMBER (SLOT “), (SHELF *), (CAB 01)) 
(TEST 00), (PASS 0001) If an error is detected, make note 
of the error and refer to Practice 
9125-060-35O-NA, 
Troubleshooting. 
Page 1 of 2 
912!5-060-204-NA Issue 1 Revision 0 204 5-13  
						

							Commissioning 
Chart 5-6 SX-ZUOU SG Maintenance Unit Commissioning 
(continued) 
Step 
Action Comments 
4. Enter the following command: Refer to Appendix A., Table A2-6, 
for an example of the SHOW 
SHOW PANEL PANEL display. 
Check that the Maintenance Terminal displays the 
status of the Maintenance Unit. 
5. 
Enter the following command: 
SHOW PANEL N (Where N is the desired 
maintenance unit number) 
Check that the Maintenance Terminal displays the 
status of the Maintenance Unit specified. 
6. Switch activity to Plane A, connect the Maintenance Refer to Appendix A., Table A2-6 
Terminal to the TERMINAL A port on the Maintenance for an example of the SHOW 
Connector panel of the Control Cabinet, and repeat PANEL N display. 
steps 2 through 5. 
7. Remove the commissioning diskette from the Floppy 
Disk Unit. 
8. Hardware commissioning is now complete. Refer to 
Practice 9120-060-200, Installation, for software 
installation. 
Page 2 of 2 
204 5-14 
Revision 0 9125-060-204-NA Issue 1  
						

							6 
’ SX-2000FD ICS 
COMMISSIONING 
Install Circuit Cards 
Non-Redundant Control Node 
6.1 
Ensure that the Main Control cards and Fiber Interface Modules are installed in the 
correct card slots before loading the commissioning software. Chart 6-1 describes 
the card installation procedure for the Non-redundant Control Node of the SX-2ooo FD 
system. The procedure for a Redundant Control Node is shown in the next chart, 
Chart 6-2. 
Chart 6-l Install Circuit Cards in the SX-2UOU FD ICS Non-Redundant Control Node 
l Main Controller II Card: Shelf 1, Slot 1 
* Control Resource Card: Shelf 1, Slot 2 
l Fiber Interface Modules: Shelf 2, Slots l-4, as 
card does not begin self-test, or if 
errors are indicated on the numeric 
display, reinsert the card. Reset 
the MC II card by pressing PANEL 
ENABLE and RESET A on the 
Maintenance Panel. If the card 
fails self-test a second time, 
912!5-060-204-NA Issue 1 Revision 0 204 6-l  
						

							Commissioning 
Redundant Control Node 
Ensure that the Main Control cards and Fiber interface Modules are installed in the 
correct card slots before loading the commissioning software. 
Chart 6-2 describes the 
card installation procedure for the Redundant Control Node. 
Chart 6-2 Install Circuit Cards in the SX-2000 FD ICS Redundant Control Node 
Step Action Comments 
1. Ensure the following cards are installed in the Control Refer to Figure 6-l. 
Node: 
l Plane A Main Controller II Card: Shelf 1, Slot 2 
l Plane A Control RAM II Card: Shelf 1, Slot 3 
l Plane A Circuit Switch Matrix II Card: Shelf I, Slot 4 
l Plane B Circuit Switch Matrix II Card: Shelf 1, Slot 5 
l Plane B Control RAM II Card: Shelf 1, Slot 6 
l Plane B Main Controller II Card: Shelf 1, Slot 7 
l Control Resource Card: Shelf 1, Slot 8 
l Fiber Interface Modules: Shelf 3, Slots I-II, 
as required 
2. Apply power to the Control Node by setting the two 
PSU power switches on the node backplate to ON. 
3. Check that the Main Controller II (MC II) cards and If an MC II or Control Resource 
the Control Resource card begin power-up self tests. card does not begin self-test, or if 
errors are indicated on the numeric 
display, reinsert the card. Reset 
the MC II card by pressing PANEL 
ENABLE and RESET A (or RESET 
B for the Plane B MC II card) on 
the Maintenance Panel. If the card 
fails self-test a second time, 
replace it. 
Power-up self tests are only 
performed when power is first 
applied to installed cards. 
4. Proceed to Chart 6-3 for installation of cards in the 
Peripheral Node(s). 
204 6-2 Revision 0 9125-060-204-NA Issue 1  
						

							r 
m IA 
SX-2000 FD ICS Commissioning 
Peripheral Nodes 
Ensure that the Peripheral Control cards, Peripheral Interface cards, and one Fiber 
Interface Module are installed in the correct card slots in each Peripheral Node before 
loading the commissioning software. Chart S--S describes the card installation 
procedure for the Peripheral Node. 
Chart 63 Install Circuit Cards in the SX-2000 FD ICS Peripheral Nodes 
. Fiber Interface Module: Shelf 1, Slot 17 
l Peripheral Resource Card: Shelf 2, Slot 17 
ower switches on th 
indicated on the numeric display, 
reinsert the card. If the card fails 
self-test a second time, replace it. 
9125-060-204-NA Issue 1 Revision 0 204 6-3  
						

							Commissioning 
DSU Nodes 
Ensure that the Peripheral Resource cards, Digital Service Unit (DSU) cards, and Fiber 
Interface Module(s) are installed in the correct card slots in each DSU Node before 
loading the commissioning software. Chart 6-4 describes the card installation 
procedure for the DSU Nodes, 
Chart &4 Install Circuit Cards in the SX-2000 FD ICS Peripheral Nodes 
Step Action Comments 
1. Ensure that the following cards are installed in the first Refer to Figure 6-2. 
DSU Node: 
Leave all other cards (except filler 
l Fiber Interface Module: Shelf 1, Slot 1 plates) uninstalled. 
l Peripheral Resource Cards: Shelf 2, Slot 1 and 6 
l Fiber Interface Module: Shelf 1, Slot 6 (optional) 
2. Apply power to the DSU Node by setting the PSU 
power switch on the node backplate to ON. 
3. Check that the Peripheral Resource cards in each 
node begin power-up self tests. If the Peripheral Resource card 
does not begin self-test, or if errors 
are indicated on the numeric 
display, reinsert the card. If the 
card fails self-test a second time, 
replace it. 
Power-up self tests are only 
performed when power is first 
applied to installed cards. 
4. 
Install DSUs in slots 2 to 5 (Shelf 1) of the DSU Node. 
5. Repeat Steps 1 to 4 for each additional DSU Node. 
6. 
After circuit cards have been installed in all DSU 
Nodes, the card installation process is completed. Go 
to Chart 6-5 for instructions on loading 
commissioning software onto Plane A of the SX-2000 
FD system. 
204 6-4 
Revision 0 912!%060-204-NA issue 1  
						

							m IA 
SX-2000 FD ICS Commissioning 
SLOT 
SLOT 
SLOT 
SLOT SHELF 1 
I r-------. NON-REDUNDANT CONTROL NODE 
SHELF2 
1 
2 3 4 
-----________ SLOT 
SHELF3 
SHELF2 SHELF 1 
,-_____-_________ 
_I , - - - - - - - _I ,_ _ _ _ _ 
I 
1 I 
’ I 
ooco 
1 
2 3 4 
oo[ll 
5 6 7 6 
mlFl REWNDANT CONTROL NODE 
Figure 6-l SX-2000 FD Control Node Circuit Card Locations 
9125-060-204-NA 
Issue 1 Revision 0 204 6-5  
						

							Commissioning 
SHELF2 SHELF 1 SHELF2 
I 1 
Bm.37 
I I 
SHELF1 
____-____---______--____________________--------------, 
Figure G2 SX-2000 FD Peripheral and DSU Node Circuit Card Locations 
204 6-6 
Revision 0 9125-060-204-NA issue 1