Mitel Sx 200 Ml Pabx Lightware 16 Instructions Guide

Appendix A - Programming Error Messages 
Table A-l Programming Error Messages (continued) 
Error Message 
Unprogram all non-T1 ISDN Cards from 
bay X before adding 2nd Tl ISDN Card Meaning 
This message appears if you try to program a second 
Tl Card while any card, other than a Tl Trunk Card, is 
programmed in a 96-port bay. 
User currently programming feature keys Cannot EXPAND SET while set user is accessing 
Try again later Program Feature Key feature. 
Valid COS range must be entered before Before a...

Customer Data Entry 
Table A-1 Programming Error Messages (continued) 
Error Message 
Value XX is outside valid range for 
SUBCIRCUIT (X - X) Meaning 
Subcircuits 1 to 4 refer to the DTMF Receivers; they 
cannot be accessed. The only subcircuits that can be 
accessed are the relays on the Receiver/Relay Module. 
These are subcircuits 5 and 6. 
ValueXXisoutsidevalid rangeforTENANT The selected tenant group number is invalid; the range 
(1 -25) is 1 to 25. Tenant group numbers are used in the 
following...

Appendix B 
Blank CDE Forms 
This appendix contains blank CDE forms that you can use to plan system programming. 
Forms that cannot be edited are not shown in this appendix. 
You begin planning the programming by defining the location of all peripheral cards 
and modules in the system. 
For information on the actual CDE forms, refer to the main body of this document. 
Further information on individual features is contained in the FeaW-es DescQMon 
Practice. 
March 1997 Issue 1 Revision 0 B-l  

Customer Data Entry 
FORM 01 - SYSTEM CONFIGURATION 
B-2 6 
Issue 1 Revision 0 March 1997  

Appendix B - Blank CDE Forms 
FORM 02 - FEATURE ACCESS CODES 
Feature Numbers 
01 
02 
03 
04 
05 
06 
07 
08 
09 
10 
11 
12 
13 
14 
15 
16 
17 
18 
19 
20 
21 
22 
23 
24 
25 
26 
27 
28 
29 
30 
31 Maintenance Functions (Test Line) 
Direct Inward System Access 
Callback Busy  
Call Hold 
Call Hold Retrieve (Local) 
Call Hold Retrieve (Remote) 
Abbreviated Dial Access 
Clear All Features 
SUPERSET Telephone Loopback Test 
Tone Demonstration 
ADL Call Setup 
ADL Disconnect 
Last Number Redial...

Customer Data Entry 
40 
41 SUPERSETTeL Maid in Room Status Display 
Send Message 
42 Call Message Sender of Oldest Message 
B-4 Issue 1 Revision 0 March 1997  

Appendix B - Blank CDE Forms 
FORM 03 - CLASS OFSERVICE DEFINE 
C;;N&n Class Of Service Option Name Enter COS ## (01 to 50) 
and COS Name 
100 I 
Attendant Bell Off 
204 Call Block Applies (Room To Room) 
Page I of 6 
March 1997 Issue 1 Revision 0 B-5  

Customer Data Entry 
B-6 Issue 1 Revision 0 March 1997  

Appendix B - Blank CDE Forms 
COS Option 
Numbers Class Of Service Option Name Enter COS ## (01 to 50) 
and COS Name 
239 Priority Dial 0 
240 Line Privacy 
241 Receive Only 
242 
Repeated Camp-On Beep 
243 Non-Busy Extension 
244 Room Status Applies 
245 Abbreviated Dialing Access 
246 SMDR - Extended Record 
247 
SMDR - Record Meter Pulses 
I 24% TAFAS Any Access I I I I I I 
255 Repeated Camp-On Beeps Timer 5 - 15 Seconds 
256 UCD Music On Hold Timer 0 - 50 Minutes 
257 Flash Over Trunk 
258 Display...

Customer Data Entry 
Class Of Service Option Name Enter COS # (01 to 50) 
and COS Name 
604 PBX SUPERSETTel. - Automatic Outgoing Line 
605 SUPERSETTelephone - Message Program 
606 SUPERSETTeL - Enhanced Answering Position 
607 SUPERSETTelephone - Associated Modem Line 
Page4of6 1 
Issue 1 Revision 0 March 1997