Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

SECTION MITL9109-094-320-NA dCHART 5-5
SERIAL CALL
StepActionVerify
1Station “A” lifts handset,Incoming trunk call appears at Attendant Console (see
accesses an outgoingChart 5-l). SERIAL CALL 
softkey is displayed.
trunk, then 
accejses an
incoming trunk.
2Press SERIAL CALL sof-tkey. SRC display shows incoming trunk data and SER status
flag.
3Attendant dials station “B”Station “B” rings. Station “A” receives Ringback Tone.
directory number, thenAttendant Console returns to idle condition.
presses...

System Test Procedures
CHART 5-7
ABBREVIATED DIAL
Part 1 -Programming Abbreviated Dial Numbers
1Press the FUNCTION key.Softkey prompts change. SRC and DST displays blank.
2Press ATT FUNCTIONSoftkey prompts change.
softkey (F2).
3Press ABBR DIAL softkeyLCD responds by displaying the message: Enter Index
m-Number:-
4Enter Abbreviated DialDigits are displayed as they are entered from telephony
Entry Number (000-999).keypad. The 
-key can be used to back up to and clear
incorrect entries. ENTER 
softkey is...

SECTION MITL9109-094-320-NACHART 5-8
DO NOT DISTURB
StepActionVerify
1Attendant dials station “A” See Chart 5-2.
directory number.
2Station “A” lifts handset.Station “A” and Attendant Console are connected. DST
display shows station “A” data. NO DTSTB 
softkey is
displayed.
3Attendant presses F6 (NODND status flag appears in DST display. (Do Not Disturb is
DTSTB softkey).
enabled.)
4Attendant presses F6 (NODND status flag removed in DST display. (Do Not Disturb
DTSTB softkey).is disabled.)
5Press...

System Test Procedures
CHART 5-9OVERRIDE
StepActionVerify
1Enable Do Not Disturb onSee Chart 5-8.
station “A”.
2Attendant dials station “A”Reorder Tone returned. DST display shows DND status
directory number.flag for station “A”.
3Press OVERRIDE softkey.Ringback Tone returned. Station “A” rings.
4Station “A” lifts handset.Station “A“ and Attendant Console are connected.
5Press RELEASE.Station “A” and Attendant Console are disconnected.
Attendant Console display returns to idle condition.
6Set handsets...

SECTION MITL9109-094-320-NACHART 5-10
FLEXIBLE NIGHT SERVICE
StepActionVerify
1Press FUNCTION key.Function softkeys are displayed.
2Press ATT FUNCTIONSoftkey prompts change.
softkey.
3Press MORE... sof-tkey.Softkey prompts change.
4Press FLEX NIGHT softkey.LCD responds by displaying the message:
Enter Trunk Number:-
5Enter digits of trunkDigits are displayed as they are entered from the
number.telephony keypad.
6Press either the NIGHT 1
LCD responds by displaying trunk data, and the message:
or NIGHT 2...

System Test ProceduresteD IActionCHART 5-11
TRUNK BUSY OUT OPERATIONIVerify
1Press the FUNCTION key.Function softkeys displayed.
2Pre::s ATT FUNCTIONSoftkey prompts change.
softkey.
3Press TRUNKS softkey.LCD responds by displaying the message: Enter Trunk
Number:-
4Enter trunk number digits.Softkey prompts change. Digits appear as they are entered
from telephony keypad.
5Press BUSY OUT softkey.Trunk data is displayed on LCD. IDLE status flag appears,
and SET 
softkey appears.
6Press SET softkey.Display...

SECTION MITLSI 09-094-320-NACHART 5-12
MESSAGE WAITING
StepActionVerify
1Attendant dials station “A”Station “A” rings. Attendant Console receives ringbackdirectory number.tone. DST display shows station “A” data. MSG WAITING
softkey is displayed.
2Press MSG WAITINGMSW status flag appears against station “A” data.
softkey.
3Press RELEASE.Attendant Console returns to idle condition. After a delay
station “A” receives three bursts of ringing, indicating
there is a message waiting.
4Station “A” dials...

System Test Procedures
CHART 5-13
ATTENDANT CALL FORWARDINGStepActionVerify
1Press FUNCTION key.Function softkeys are displayed.
2Press ATT FUNCTIONSoftkey prompts change.
softkey.
3Press STATIONS softkey.LCD display responds by displaying the message: Enter
Extension Number:-
4Enter station “A” directoryDigits appear on LCD as they are entered from telephony
number.keypad. CALL FWD 
softkey is displayed.
5Press CALL FWD softkey.Softkey prompts change. LCD displays
message:
1Currently not set Forward...

SECTION MITL9109-094-320-NACHART 5-13 (CONT’D)
ATTENDANT CALL FORWARDING
StepActionVerify
12Press CANCEL softkey.LCD display returns to idle condition. (Call Forwarding is
canceled at station “A”.)
13Repeat Step 9.Station “A” rings. Attendant Console receives RingbackTone. Station “A” appears as DST.
14Press RELEASE.Station “A” stops ringing. Ringback Tone removed from
Attendant Console. Attendant Console display returns to
idle condition.
15Repeat Steps 1 through 5.Call Forwarding is enabled for station...

System Test Procedures
CHART 5-14
ATTENDANT STATION BUSY-OUTStepAction
Verify
1Press the FUNCTION key.Function softkeys are displayed.
2Press ATT FUNCTIONSoftkey prompts change.
softkey.
3Press STATIONS softkey.Attendant Console LCD displays the message:
Enter Extension Number:-
4Enter station “A” directoryDigits are displayed on LCD display as they are entered
number.from telephony keypad. BUSY OUT 
softkey is displayed.
5Press BUSY OUT softkey.SET softkey is displayed.
6Press SET softkey.Attendant...