Mitel SX-200 DIGITAL Pabx Information Manual

System Test Procedures 
CHART 5-3 
CALL HOLD AND RETRIEVE 
Step Action Verify 
1 Station “A” lifts handset. Dial Tone returned. 
2 Station “A” dials Attendant See Chart 5-l. 
Access Code. 
3 Attendant presses HOLD 1 Station “A” receives Music On Hold, if provided, or silence. 
key. The SRC area of the Attendant Console LCD is blanked. 
HOLD 1 LED is on. ANSWER LED is off. 
4 Wait the time-out period. HOLD 1 LED flashes. Warbler sounds with Attendant 
Console Recall Tone (one burst of tone for HOLD slot...

System Test Procedures 
CHART 5-4 
RECALL 
Step I Action Verify 
1 
4 Perform Steps 1 through 3 
of Answering Calls - Part 1 
(Internal). See Chart 5-1. 
Attendant dials station “B” 
directory nurnber, then 
presses RELEASE. 
Allow station “B” to ring 
until recall timer causes 
recall. 
Press ANSWER key or 
RECALL softkey. Station “8” rings. Station “A” receives Ringback Tone. 
Attendant Console returns to idle condition. 
Attendant Console rings. ANSWER LED flashes. Station “B” 
stops ringing. RECALL...

System Test Procedures 
Step 
Step Action 
Station “A” lifts handset, 
accesses an outgoing 
trunk, then accesses an 
incoming trunk. Incoming trunk call appears at Attendant Console (see 
Chart 5-l). SERIAL CALL softkey is displayed. 
Press SERIAL CALL softkey. SRC display shows incoming trunk data and SER status 
flag. 
Attendant dials station “B” 
directory number, then 
presses RELEASE. 
Station “B” lifts handset. Station “B” rings. Station “A” receives Ringback Tone. 
Attendant Console returns to...

System Test Procedures 
CHART 5-7 
ABBREVIATED DIAL 
Part 1 - Programming Abbreviated Dial Numbers 
1 Press the FUNCTION key. Softkey prompts change. SRC and DST displays blank. 
2 Press ATT FUNCTION Softkey prompts change. 
softkey (F2). 
3 Press ABBR DIAL softkey LCD responds by displaying the message: Enter Index 
w3). Number:- 
4 Enter Abbreviated Dial Digits are displayed as they are entered from telephony 
Entry Number (000-999). keypad. The - key can be used to back up to and clear 
incorrect...

System Test Procedures 
CHART 5-8 
DO NOT DISTURB 
Step Action Verify 
1 Attendant dials station “A” See Chart 5-2. 
directory number. 
2 Station “A” lifts handset. Station “A” and Attendant Console are connected. DST 
display shows station “A” data. NO DTSTB softkey is 
displayed. 
3 Attendant presses F6 (NO DND status flag appears in DST display. (Do Not Disturb is 
DTSTB softkey). enabled.) 
4 Attendant presses F6 (NO DND status flag removed in DST display. (Do Not Disturb 
DTSTB softkey). is...

System Test Procedures 
CHART 5-9 
OVERRIDE 
Step Action Verify 
1 Enable Do Not Disturb on See Chart 5-8. 
station “A”. 
2 Attendant dials station “A” Reorder Tone returned. DST display shows DND status 
directory number. flag for station eK. 
3 Press OVERRIDE softkey. Ringback Tone returned. Station “A” rings. 
4 
Station “A” lifts handset. Station “A” and Attendant Console are connected. 
5 Press RELEASE. Station “A” and Attendant Console are disconnected. 
Attendant Console display returns to idle...

System Test Procedures 
CHART 5-10 
FLEXIBLE NIGHT SERVICE 
Step Action Verify 
1 Press FUNCTION key. Function softkeys are displayed. 
2 Press ATT FUNCTION Softkey prompts change. 
softkey. 
3 Press MORE... softkey. Softkey prompts change. 
4 Press FLEX NIGHT softkey. LCD responds by displaying the message: 
Enter Trunk Number:- 
5 Enter digits of trunk Digits are displayed as they are entered from the 
number. telephony keypad. 
6 Press either the NIGHT 1 LCD responds by displaying trunk data, and the...

CHART 5-11 
TRUNK BUSY OUT OPERATION 
Step Action Verify 
1 Press the FUNCTION key. Function softkeys displayed. 
2 Press ATT FUNCTION Softkey prompts change. 
softkey. 
3 Press TRUNKS softkey. LCD responds by displaying the message: Enter Trunk 
Number:- 
4 Enter trunk number digits. Softkey prompts change. Digits appear as they are entered 
from telephony keypad. 
5 Press BUSY OUT softkey. Trunk data is displayed on LCD. IDLE status flag appears, 
and SET softkey appears. 
6 Press SET softkey. Display...

System Test Procedures 
CHART 5-12 
MESSAGE WAITING 
Step Action Verify 
1 Attendant dials station “A” Station “A” rings. Attendant Console receives ringback 
directory number. tone. DST display shows station “A” data. MSG WAITING 
softkey is displayed. 
2 Press MSG WAITING MSW status flag appears against station “A” data. 
softkey. 
3 Press RELEASE. Attendant Console returns to idle condition. After a delay 
station “A” receives three bursts of ringing, indicating 
there is a message waiting. 
4 Station...

System Test Procedures 
CHART 5-13 
ATTENDANT CALL FORWARDING 
Step I Action Verify 
8 
9 
10 
11 Press FUNCTION key. 
Press ATT FUNCTION 
softkey. 
Press STATIONS softkey. Function softkeys are displayed. 
Softkey prompts change. 
LCD display responds by displaying the message: Enter 
Extension Number:- 
Enter station “A” directory Digits appear on LCD as they are entered from telephony 
number. keypad. CALL FWD softkey is displayed. 
Press CALL FWD softkey. Softkey prompts change. LCD displays...