Mitel SX-200 DIGITAL Pabx Engineering Information Manual
Here you can view all the pages of manual Mitel SX-200 DIGITAL Pabx Engineering Information Manual. The Mitel manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 211
Troubleshooting 16. If the destination is idle, the MCC connects the DSP to the originator and ringback tone is supplied. 17. The MCC sends a cadence message to the PCC of the origina- tor to provide interruption of the ringback tone. 18. 19. The MCC sends a message to the PCC to ring the destination. When the destination answers, the Scanner detects the off- hook. 20. 21. The Scanner sends an IRQ to the PCC. The PC6 stops ringing and sends a message to the MCC in- dicating that the...
Page 212
MITEL STANDARD PRACTICE SECTION MITL9108-093-351 -NA Issue 2, September 1986 SX-208” DlGlTAL PRIVATE AUTOMATIC BRANCH EXCHANGE (PABX) RS-232 MAINTENANCE TERMINAL Copyright of MITEL Corporation 1986 TM - Trademark of MITEL Corporation @Registered Trademark of MITEL Corporation
Page 213
K-232 Maintenance Terminal P CONTENTS PAGE l-GENERAL ....................................... . l-l Introduction ..................................... l-l Reason for Reissue ............................... l-l How to Use this Section ........................... l-l 2. SETTING UP ...................................... 2-l -- Terminal Type .................................... 2-l Connection to the System (Terminal) .................. 2-l Connection to the System (Printer)...
Page 214
RS-232 Maintenance Terminal CONTENTS (CONT’D) PAGE 5. REPORTS LEVEL FUNCTIONS . . . . . . . . . . ‘. . . . . . . . . . e s a . . 5-1 introduction . . . . . . . . . . . e . . . . . . . . . . . . . a . . n . . r n . m . . 5-l EQUIPMENT CONFIGURATION REPORT . . . . . . e . . 0 0 . . . . . . 5-l Entire System . . . e . . . . . . = . m . . . . . . . . . . . . . . . . . . . = . e 5-l Specific Card Slot . 0 . . . v . 0 0 . . s e e . . s . m 0 . s D e s . . D m 0 D 5-l SpecificExtension . . . . . . . . ....
Page 215
RS-232 Maintenance Terminal CONTENTS (CONT’D) PAGE DISABLING POWER-UP DIAGNOSTICS . . . . . . . . . . . . . . . . . 7-4 For an Entire Bay . . . . . . l). . m . . . . . . . . . . e . . . . . . . . . . . 7-4 For an Entire Peripheral Card . . . . . . . . . . . . . . . . . . . . . . . 7-4 For a Specific Circuit . . . . D , 0 . s . . D a n . . . . D . . . 0 . . . . . . 7-4 For a Specific Extension *. r . . -. 0 0 . . n . . . . . . . m . . . . . . 7-5 For a Specific Device Type e . . a . . . D . m D m ....
Page 216
RS-232 Maintenance Terminal FIGURE TITLE PAGE 2-1 SX-200@ DIGITAL Control Maintenance Panel 2-2 2-3 3-l 4-1 4-2 4-3 5-l 5-2 5-3 5-4 5-5 6-l 7-l (Universal Cabinet) . . . . . . m . . m . . . . 0 D . n . . . . . m . . 2-4 SX-200@ DIGITAL Control Maintenance Panel (Standard Cabinet) . . r -. s D . 0 . s 0 q m m s s . D . m m D s . D 2-5 SX-200@ Bay 2 Backplane . . 0 . . . . . . . . 0 . m D . 0 s . . m D 2-6 Top Level Maintenance Terminal Screen Layout . . . D 3-4 Terminal/Printer Port...
Page 217
RS-232 Maintenance Terminal 1. GENERAL Introduction 1.01 This Section is intended to assist maintenance personnel in obtaining the maximum benefit from the extensive built-in maintenance features of the SX-200@ DIGITAL PABX with Generic 1000 and Generic 1001 software. It provides information on the setting up and. use of the RS-232 Maintenance Terminal, which is the prime maintenance tool on the SX-200@ DIGITAL system. The maintenance terminal is also used for Customer Data Entry (CDE) and...
Page 218
RS-232 Maintenance Terminal 2. SETTING UP Terminal Type 2.01 The SX-200@ DIGITAL PABX maintenance subsystem is de- signed to interface with virtually any 80-column terminal hav- ing an RS-232 type interface. The terminal may be either a video display terminal or a hard copy teleprinter. For ease of operation, a video display terminal capable of using the ANSI X3.64-1977 special character set for special graphics (i.e., VT-100 compatible) is preferred. The system prompts the user to specify the...
Page 219
RS-232 Maintenance Terminal a 8 data bits a 1 start bit a 1 stop bit a no parity a 1200 baud. Note that the baud rate of the printer port may be changed via a command from the maintenance terminal. Login Procedures 2.04 With the terminal powered-up, or reset, the system is ready for the user to log in. Pressing the RETURN key twice within 1 second causes the system to automatically determine the terminal’s baud rate, and to query the user for the terminal type as follows: l- VT-1 00...
Page 220
RS-232 Maintenance Terminal 0 MAlNTl l MAINT2 . SUPERVISOR 0 ATTENDANT. Respond to the username prompt by entering one of these usernames. The system will then query the user for a password: ENTER PASSWORD : The SX-200@ DIGITAL system database contains one default password for all of the usernames. Passwords may be changed as required (see paragraph 4.06). The default password for all users is “1000”. Note that, for security reasons, the system does not echo the password back to the terminal....