Minolta magicolor 2200 User Manual

Maintaining the Printer 51
„Never use sharp or rough implements, such as wire or plastic cleaning pads.
„Always close the printer covers gently. Never expose the printer to vibrations.
„Do not put a cover on the printer immediately after using it. Turn it off and wait until it 
cools down. 
„Do not leave the printer’s covers open for any length of time, especially in well-lit 
places; light may damage the OPC drum cartridge.
„Do not open the printer during printing.
„Do not tap paper stacks on the...

Cleaning 52
Cleaning 
You should perform a thorough cleaning every 30,000 single-sided pages or 12 months, 
whichever comes earlier.
Always test any cleaning solution (such as a mild detergent) on a small area of your printer 
to check the solution’s performance. 
Use Avoid
A soft dry
 cloth to clean the 
control panelSharp or rough implements (such as wire or plastic 
cleaning pads)
Any liquid
A soft damp
 cloth to clean the printer Sharp or rough implements (such as wire or plastic 
cleaning pads)
Mild...

 
4
Troubleshooting
Downloaded From ManualsPrinter.com Manuals 

Introduction 54
Introduction
This chapter provides information to aid you in resolving printer problems you may 
encounter, or at least guide you to the proper sources for help. 
Printing a Status Page
Print a status page to verify the printer is printing correctly. 
Preventing Media Jams 
Press Key (Until) Display Reads
OnlineIDLE 
(and online LED is off)
MenuOPERATOR CONTROL
Next (  )ADMINISTRATION
SelectADMINISTRATION–SPECIAL PAGES
SelectPRINT STATUS
SelectYES
OnlineIDLE 
(and online LED is on)
 Make...

Automatic Jam Recovery 55
Automatic Jam Recovery
The magicolor 2200 provides automatic jam recovery (when enabled through the 
Administration/Engine/Page Recovery menu). After you remove any jammed media, 
printing automatically resumes from the page the printer stopped at when the jam 
occurred.
5For automatic jam recovery to work, it is necessary to leave the printer turned on when 
you remove the jammed media. 
You always adjust the media width regula-
tion guides in the multipurpose tray 
after...

Understanding the Media Path 56
Understanding the Media Path
Understanding the printer’s media path will help you locate media jams. 
c
cc cMedia exit unit
d
dd d
Output tray
e
ee e
Fuser
f
ff f
Transfer belt
g
gg g
OPC drum cartridge
h
hh h
Duplex unit (standard on DP model)
i
ii i
Multipurpose tray
j
jj j
Upper media tray
k
kk k
Lower feeder unit and optional tray (standard on DP model)
l
ll l
5-bin mailbox
 
Simplex
Duplex
c
cc c
d
dd d
DP Model
DP Model with
5-bin Mailbox
e
ee e
f
ff f
g
gg gh
hh h...

Clearing Media Jams 57
Media Tray (Upper Tray Standard on All Models and Optional Tray 
Standard on DP Model)
The media tray(s) is (are) located at the bottom front of the printer. The media is picked 
from the tray, passed under the OPC drum cartridge and the transfer belt, passed through 
the fuser, and delivered via the paper exit unit to the output tray on top of the printer.
Multipurpose Tray (Standard on All Models)
The multipurpose tray is located at the right of the printer. The media is picked...

Clearing Media Jams 58
Attention
The image is not fixed on the media before the fusing process. If you touch the 
printed surface, the toner may stick to your hands, so be careful not to touch the 
print face when removing the jammed media. Make sure not to spill any toner inside 
the printer. Unfused toner can dirty your hands, clothes, or anything else it gets on. If 
you accidentally get toner on your hands, wash them in cool water. If you 
accidentally get toner on your clothes, lightly dust them off...

Clearing Media Jams 59
Clearing Misfeed (Upper or Optional Tray) Jams  
1Remove the media tray(s).
2Carefully remove the jammed media.
3Shuffle the media currently in the tray and 
even up the front edges.
4Reinsert the media printing face up.
Make sure the media is lying flat, is under the media sepa-
rating tabs, and doesn’t exceed the media limit mark. 
Check to see if the media width guides are correct.
5Slide the tray(s) back into the printer.
6Open the front cover, then close it.
The media jam...

Clearing Media Jams 60
Clearing Misfeed (Multipurpose Tray) Jams
1Remove the media from in the multipurpose tray.
2Carefully remove the jammed media.
3Shuffle the media that was removed in step 1 and 
even up the front edges.
4Reinsert the media printing face down.
Make sure the media is lying flat and doesn’t exceed the 
media limit mark. Check to see if the media width guides 
are correct.
5Open the front cover, then close it.
The media jam display is cancelled.
Clearing Inner Jams, Outer Jams, and...