Minolta magicolor 2200 User Manual

Replacing Toner Cartridges 11
Toner Cartridge Handling
Attention
Do not hold a toner cartridge vertically. Do not touch the 
toner roller surface 
c or the protective shutter d. This 
could lower image quality.
Keep toner cartridges:
„In their packaging until you’re ready to install them.
„In a cool, dry location away from sunlight (due to heat). 
The maximum storage temperature is 95
° F (35
° C) and the maximum storage humid-
ity is 80% without condensation.
„Level during storage. 
Do not stand or...

Replacing Toner Cartridges 12
3Press  the toner cartridge carrousel button 
cand release the button dbefore turning 
the carrousel dial 
ecounterclockwise until 
it stops.
The carrousel rotates 90° and stops.
The toner cartridge carrousel may start to 
turn automatically from the weight of the 
inserted toner cartridge. Make sure you 
have fully turned to the next slot before try-
ing to insert another toner cartridge.
4Continue step 3 until the color to be 
replaced is visible.
5Pull the release lever...

Replacing the OPC Drum, Laser Lens Cover, and Waste Toner Pack 13
7Distribute the toner inside the cartridge. 
Holding a cartridge with both hands, gently shake it 
five or six times.
5Each toner cartridge has a colored end that 
corresponds to a colored label inside the cartridge slots. Always install the toner 
cartridge in the slot with a label of the same color.
8Place the front end of the toner cartridge 
installation guides into the cartridge installa-
tion rails on the cartridge carrousel.
9Gently...

Replacing the OPC Drum, Laser Lens Cover, and Waste Toner Pack 14
When the OPC drum is worn out, the message REPLACE DRUM
 appears. The printer will 
not print until the drum kit is replaced. 
When you replace the OPC drum cartridge after a DRUM LOW 
or REPLACE DRUM 
message displays in the message window, the printer automatically recovers. However, the 
replaced waste toner pack consumables monitoring system must be reset.
The three items below are included in the OPC drum kit. If one needs replacing,...

Replacing the OPC Drum, Laser Lens Cover, and Waste Toner Pack 15
3Carefully remove the waste toner pack using 
the handle.
Keep the waste toner pack upright so the 
toner does not spill.
4Turn the two caps labeled “A” counterclock-
wise and remove them.
5Twist the two “A” caps c onto the two “A” 
holes 
d. 
Turn the caps clockwise to secure them.
1
1
2
2
11
2
2
Downloaded From ManualsPrinter.com Manuals 

Replacing the OPC Drum, Laser Lens Cover, and Waste Toner Pack 16
6Remove waste toner pack cap labeled “B” and insert 
it into hole “B.”
7Dispose of the used waste toner pack.
5Dispose of it properly according to your local 
regulations (do not dispose of it by burning).
8Continue with replacing the OPC drum 
cartridge.
Reinstall the new waste toner pack after replacing 
the OPC drum.
Removing the Used OPC Drum Cartridge 
1With the front cover open, rotate the trans-
fer belt unit left release lever...

Replacing the OPC Drum, Laser Lens Cover, and Waste Toner Pack 17
3Support the bottom of the drum with your 
hand, then carefully pull the cartridge toward 
you and remove it.
5Dispose of it properly according to 
your local regulations.
Replacing the Laser Lens Cover 
1Press on the laser lens cover lock release lever and 
gently pull the laser lens cover toward you.
5Dispose of it properly according to your local 
regulations.
2Remove the new laser lens cover from the OPC 
drum kit box.
Attention
Do not...

Replacing the OPC Drum, Laser Lens Cover, and Waste Toner Pack 18
Installing the New OPC Drum Cartridge 
1Remove the new OPC drum cartridge from 
its shipping box.
Attention
Keep the protective sheet on the cartridge. Do not touch the protective sheet on 
the photosensitive (green) surface or scratch the surface. This could lower 
image quality.
Make sure the transfer belt left release lever is still set to its top position
(12 o’clock).
2Hold the OPC drum cartridge level, place 
the front end of the OPC...

Replacing the OPC Drum, Laser Lens Cover, and Waste Toner Pack 19
4Press on the front handle of the OPC drum car-
tridge with one hand and hold the front handle of 
the OPC protective cover with the other hand. 
5Peel the protective cover off (straight toward 
you).
5Dispose of it properly according to your local 
regulations.
6Turn the left release lever of the transfer belt 
clockwise to its correct position (2 o’clock).
This lowers the transfer belt.
Also make sure the transfer belt right release...

Replacing the Fuser Unit and Transfer Roller Kit 20
2Insert the bottom of the waste toner pack c 
into its installation position in the printer.
3Insert the top of the waste toner pack d
into its installation position in the printer 
until it is firmly seated.
4Close the printer’s front cover.
If the waste toner pack is not correctly 
installed or the transfer belt right release 
lever is at its top position (12 o’clock), the 
front cover cannot be closed. Turn on the 
printer.
5In the Operator...