Minolta magicolor 2200 User Manual

Introduction 101
Installing an Optional 5-bin Mailbox
Read this section if you purchased a 5-bin mailbox for your magicolor 2200.
Kit Contents
„Mailbox unit
„5 bins
„2 thumbscrews
„Accessory screen cover
„Power cord
Installation 
1Remove the mailbox unit from 
its shipping box. 
2Remove any tape and packing material.
Downloaded From ManualsPrinter.com Manuals 

Introduction 102
3Open the mailbox unit cover and remove any pack-
ing material from the rear of the mailbox unit.
4Close the mailbox unit cover.
5Remove any packing material from the front of the 
mailbox unit.
6Remove the two screen covers from the top of the 
printer.
Pry the covers off with your fingers. Retain these cov-
ers in case you ever want to remove the 5-bin mailbox.
7Locate the two holes, the pin, and the positioning 
guide for the mailbox.
Downloaded From ManualsPrinter.com Manuals 

Introduction 103
8Slowly lower the mailbox unit so that the two pins at 
the bottom fit into the two holes in the printer and the 
pin on the printer fits into the hole at the bottom of the 
mailbox.
5The mailbox bins will face the left side of the printer.
9Push the mailbox toward the right-hand side of the 
printer until it stops.
Downloaded From ManualsPrinter.com Manuals 

Introduction 104
10Secure the mailbox tightly with the two 
thumbscrews supplied in the kit. 
11Place the slot on the right side of the accessory screen 
cover from the kit onto the tab on the mailbox then 
press on the left side of the accessory screen cover so 
the tab on that side fits into the slot on the mailbox.
12Remove the five plastic bins from their packaging. 
13Hold a bin and insert the right side into the 
bottom level of the mailbox unit, then insert 
the left side. 
14Install the other...

Introduction 105
15Plug the mailbox power cord from the kit into the mail-
box unit (lower connection).
16Plug the other end of the power cord into the printer.
17Make sure the printer is turned off.
18Make sure the 5-bin mailbox is turned off.
Attention
Always turn off the printer before
 turning off the mailbox.
Downloaded From ManualsPrinter.com Manuals 

BuzzBox 106
19Plug the printer power cord into the mailbox unit (upper con-
nection) and into the dedicated, grounded, surge-protected 
electrical outlet.
20Turn the mailbox unit on.
21Turn the printer on.
BuzzBox 
BuzzBox is a printer accessory that warns you with a buzzer and/or a blinking light any 
time the printer goes off line. This means you’re alerted to print job interruptions, such as 
empty media trays or other consumable issues.
Whats in the Kit?
The BuzzBox kit contains the following items:...

BuzzBox 107
Installing BuzzBox
3Use the included RJ-11 cable to connect BuzzBox to the interface box.
1If you have a cable attached to the printer’s parallel port, unplug it from 
the printer.
2Attach one end of the parallel cable on the interface box to the printer’s 
parallel port.
5The BuzzBox’s ribbon cable is designed to be directly attached to the printer’s 
parallel port, not to an adapter or an additional cable. 
BuzzBox
Adapter Interface 
Box
Ribbon Cable
Downloaded From ManualsPrinter.com Manuals 

BuzzBox 108
4Choose a good location on the printer to mount the interface box. Make sure that the 
unit does not 
zinterfere with paper exiting the printer.
zcover any vents, doors, connectors, or labels. 
zcause the BuzzBox ribbon cable to stretch or twist.
5Use the adhesive-backed clips provided to mount the BuzzBox where the printer 
operator can see and/or hear it.
A 14-foot (4.2 m) cable is provided, but you can use up to a 500-foot cable (RJ-11 
4-pin or 6-pin).
6Connect the interface box to an...

Antistatic Protection 109
Antistatic Protection 
Attention
It’s very important to protect the printer controller board and any associated 
daughterboard or module from electrostatic damage while performing any task 
involving the controller board.
If an antistatic wrist strap is provided in your printer option kit, attach one end of it 
to your wrist and the other end to any convenient electrical ground (for example, the 
bare metal chassis of equipment, as on the back of a computer, that is plugged in...

Dual In-Line Memory Modules 110
Additional memory allows you to download more fonts and increase the printers buffer 
(area where data sent from the computer is stored while waiting to be printed).
5You may also need additional memory to print on some media sizes at resolutions above 
600x600 dpi.
How Much Memory Do You Need? 
The amount of RAM installed in your printer governs which resolutions can be used with 
each media size. 
If a certain resolution is chosen and the minimum amount of memory is not...