Minolta magicolor 2200 User Manual

Dual In-Line Memory Modules 111
You may also need additional memory (DIMMs) for the following:
„To print complex graphics or complex PostScript documents
„For increased collation performance
„For increased spooling performance
The magicolor 2200 has 3 DIMM slots available. The maximum memory that can be 
installed is 384 MB (3 x 128 MB DIMMs). 
„Check the startup page to make sure the printer has enough RAM installed. 
„If you have enough RAM installed, and you have configured the printer from the con-...

Dual In-Line Memory Modules 112
Installation 
Attention
It’s very important to protect the printer controller board and any associated 
circuit boards from electrostatic damage. Before performing this procedure, 
review the antistatic caution on page 112. In addition, always handle circuit 
boards by the edges only.
1If you are not to the point when you are able to print an advanced status page yet, 
skip to step 2.
If you have previously installed your printer and have confirmed that it is printing,...

Dual In-Line Memory Modules 113
5If you need to remove a DIMM before 
installing one, remove it as follows; 
otherwise skip to step 6.
5If all the DIMM connectors are filled 
and you want to install more memory, 
you have to exchange one or more 
DIMMs for DIMMs with a greater 
memory capacity. 
aUsing both thumbs, pull the latches 
(one on each side of the DIMM con-
nector) outward.
bLift the DIMM straight out of the 
DIMM connector.
6Insert the new DIMM straight down into the DIMM connector until the...

Emulations, Fonts, and Other Software 114
Emulations, Fonts, and Other Software
Emulations 
Optional emulations, such as ImageServer, LN03, and CGM are available as PostScript 
files. This section describes how to download an emulation to the printer’s hard disk.
5You must have at least one hard disk, internal or external, attached to the printer in 
order to use an optional emulation. If more than one hard disk is available, the 
emulation automatically installs itself on the disk with the most free...

Emulations, Fonts, and Other Software 115
Downloading an Emulation via an Ethernet Interface
5Before you begin this procedure, your printer and PC (or UNIX workstation) must be 
connected to an Ethernet network running TCP/IP and have valid IP addresses.
1Turn on the printer, and wait for IDLE
 to display in the message window.
2If your PC is running Windows, change to DOS.
3Insert the emulation CD-ROM or disk in your PC, and change to that drive (for 
example, if you’re using the D drive, type d:
¿
)....

Emulations, Fonts, and Other Software 116
9When the Disk light stops flashing and the printer’s message window reads Idle 
for at least 30 seconds, turn the printer off and then on again.
10When downloading is complete, reboot the printer.
The emulation should be listed in the Options section of the printer’s startup page, in 
the Administration/Emulation printer’s configuration menu, and on the advanced 
status page.
5You may want to erase any installation files left on your computer (and/or...

Emulations, Fonts, and Other Software 117
Downloading Disk Fonts via CrownAdmin
We recommend that you use CrownAdmin to download PostScript fonts. Refer to the 
CrownAdmin online help for instructions.
Downloading Disk Fonts via a Parallel Interface
1Turn on the printer, and wait for IDLE
 to display in the message window.
2Insert the font disk or CD-ROM in your PC, and change to that drive (for example, if 
you’re using the A drive, type a:
¿
).
3Send the fonts to the printer’s hard disk. Type
copy...

Kanji Font Internal IDE Hard Disk 118
7At the ftp>
 prompt, change to binary mode by typing
bin
¿
8At the ftp>
 prompt, send the fonts file to the printer’s hard disk by 
typing
put filename¿
where filename is the name of the installation file.
The printer’s message window reads 
1 Active Job to indicate that the fonts are 
being downloaded to the hard disk. The 
ftp> prompt returns when the fonts have 
finished loading.
9At the ftp>
 prompt, end the ftp session by typing
quit
¿
10When the Disk light...

Kanji Font Internal IDE Hard Disk 119
zFutoMinA101-Bold
zJun101-Light
zMidashiGo-MB31
zMidashiMin-MA 31
„IDE hard disk with ribbon cable attached
„IDE hard disk bracket
„4 screws
Hardware Requirements
„A Macintosh, IBM PC, or compatible computer 
Software Requirements
„An application (such as a word processing or desktop publishing package) that sup-
ports the PostScript printing. If you’re using a Macintosh, the following Macintosh 
system software:
zKanjiTalk, version J1-6.0.7 or later
zSystem File,...

QFORM 120
Installing a Kanji Font Internal IDE Hard Disk
Attention
The Kanji fonts are factory installed on a formatted hard disk drive. DO NOT 
reformat or initialize the Kanji internal hard disk. Reformatting erases all data, 
fonts, and files on the disk. Your warranty does not cover this error.
The Kanji font internal IDE hard disk is installed on the controller board in the same way 
any internal hard disk is installed. See “Internal IDE Hard Disk Drive” on page 126 for 
detailed steps on installing...