Minolta magicolor 2200 User Manual

Interfaces and Daughterboards 121
„Single- and multipart forms
„Labels
„Logos and watermarks
5QFORM doesn’t support color features.
Refer to the documentation that comes in the QFORM kit for installation and usage 
instructions.
PlanetPress
PlanetPress is an electronic forms package that allows the creation and modification of 
business forms, MICR checks, bar codes, and other preprinted forms. 
Refer to the documentation that comes in the PlanetPress kit for installation and usage 
instructions....

Interfaces and Daughterboards 122
What’s in the Kit? 
An optional interface kit includes the following:
„An interface card
„Interface documentation (in hardcopy and/or on CD-ROM)
The kit may also include additional parts not required for network interface installation on 
this printer.
Installation 
Attention
It’s very important to protect the printer controller board and any associated circuit 
boards from electrostatic damage. Before performing this procedure, review the 
antistatic caution on page...

Interfaces and Daughterboards 123
aAttach the interface card 
to the controller board. 
bPosition the interface 
card so that its I/O con-
nector slides into its 
opening in the interface 
panel and that its 80-pin 
connector aligns with 
the 80-pin connector on 
the controller board.
cGently press the inter-
face card down until its connector 
is fully seated and the card is secured 
by the plastic support post(s).
Attention
Make sure that the connectors on the interface card and controller board are...

SCSI Interface 124
Using a Network Interface 
Once a network interface is installed, refer to “Connecting the Printer to the Host 
Computer,”  in the Installation Guide
 and the CrownBook 
for information on connecting 
to the network, installing the software, and configuring the interface and the network. 
SCSI Interface 
The optional SCSI interface allows you to connect up to three optional SCSI devices, 
including a hard disk, and Jaz and Zip drives. These devices provide storage for fonts,...

SCSI Interface 125
1Turn off the printer, and then disconnect the power cord 
and all interface cables from the printer.
2Loosen five screws and, using the tab on the lower side 
of the panel, pull the controller board from the printer.
3Remove the two screws holding the metal plate over the 
SCSI interface opening.
You can dispose of the metal plate and screws according 
to local regulations.
4Attach the SCSI interface card to the controller board. 
aPosition the SCSI interface card so that its ribbon...

Internal IDE Hard Disk Drive 126
Using a SCSI Interface
5Installing a SCSI interface allows the attachment of external SCSI storage devices, such 
as hard drives, JAZ, and ZIP drives. Installing the SCSI interface kit will not allow you to 
print via SCSI.
Internal IDE Hard Disk Drive
WARNING!
Make sure that the printer and all accessories are turned off before installing accessories 
involving the controller board. 
One internal IDE hard disk is supported—standard on the EN and DP models, and optional...

Internal IDE Hard Disk Drive 127
1Ensure that the printer is turned off and the power cord and all interface cables are 
disconnected.
2Loosen five screws from the controller board and, using 
the tab on the lower side of the panel, pull the controller 
board from the printer.
3Position the controller board on a flat surface so the 
controller board lies flat and the interface panel is 
facing you.
4Attach the IDE hard disk to the hard disk bracket.
Attach the IDE hard disk to the 
bracket with the...

Media Trays 128
Attention
Make sure that the ribbon cable connector and the controller board connector 
pins are properly aligned. Damage to the controller board could result if the 
pins are misaligned.
7Press down gently but firmly on the cable connector until it is fully seated. 
Attention
Do not push or pull with the ribbon cable. Use the cable connector.
8Align the support posts with the holes on the controller board, and then press down 
to secure the hard disk to the controller board. 
So that you...

Printer Stand/Cabinet 129
Printer Stand/Cabinet 
A tabletop- or floor-model printer stand or a cabinet is available.  Follow the assembly 
instructions included with it. 
SC-210 Convenience Copier
You can expand your magicolor 2200’s functionality by connecting an SC-210 digital 
color convenience copier option to the standard parallel port on the printer (interface set to 
“non-interactive”). The SC-210 supports up to legal-size paper. An optional 25-sheet 
Automatic Document Feeder (ADF) is available....

Time-of-Day Clock (Standard on Models EN and DP) 130
1Turn off the printer, and then disconnect the power cord and all interface cables from 
the printer.
2Loosen five screws and, using the tab on the lower side of 
the panel, pull the controller board from the printer.
WARNING!
Because the time-of-day clock includes an internal battery, there is a danger of explosion if 
the clock is incorrectly installed or replaced. Replace it only with a supported 
MINOLTA-QMS time-of-day clock. Dispose of any used...