Minolta magicolor 2200 User Manual

Status, Error, and Service Messages 91
MEDIA JAM OPTIONAL TRAY
Tray jams occur between the 
standard upper or optional tray 
and the print engine. A misfeed 
jam may be as simple as a 
sheet of media not being picked, 
or it may be that the media was 
picked but not fed properly.Locate and remove the 
jam.
The lower feeder unit (optional 
on all models except the DP) 
door is open.Close the door.
MEDIA JAM TRANSFER
Transfer jams occur in the trans-
fer roller area. This type of jam 
means that the media...

Status, Error, and Service Messages 92
PAPER MISMATCH
The media detected in the tray 
doesn’t match the media size 
setting.Change the media in the 
tray or change the 
media size setting. 
PRINTING STATUS
A status page is printing Wait until after the status 
page prints, and the 
message clears.
PUT <
X> IN INPUT 
The 
 specified media is not 
in the input tray <
Y>
.Refill the tray with the 
specified type media. 
PUT <
SIZE> PAPER IN  The Operator Control/Chain 
Inputbins is set to Off and the...

Status, Error, and Service Messages 93
WAITING ON INPUT
END JOB?The compiler is waiting on 
incoming data for the first job in 
the queue. The job may not 
have an end-of-job indicator and 
therefore cannot end. The mes-
sage clears if more input arrives 
from the port or if you press the 
Cancel key. No other jobs can 
be printed until this job has 
ended.Wait until the job is fin-
ished and the printer 
goes idle to access the 
configuration menu.
WARMING UP
The printer is warming up.  Wait. No other...

Status, Error, and Service Messages 94
Service Messages
This service message... Means...
SERVICE CALL 04 MAIN UNIT
An error has been detected with the 
item indicated in the service mes-
sage. Correction of these errors is 
performed by a MINOLTA-QMS-
authorized service provider only. Con-
tact your local vendor.
A service message sometimes 
occurs as a result of an unusual com-
bination of events, not because of an 
actual problem. When the printer 
stops and a service message dis-
plays in the message...

Status, Error, and Service Messages 95
SERVICE CALL 1F FUS LOW THERMAn error has been detected with the 
item indicated in the service mes-
sage. Correction of these errors is 
performed by a MINOLTA-QMS-
authorized service provider only. Con-
tact your local vendor.
A service message sometimes 
occurs as a result of an unusual com-
bination of events, not because of an 
actual problem. When the printer 
stops and a service message dis-
plays in the message window, turn 
the printer off and then back on....

Status, Error, and Service Messages 96
HP-GL Error Codes and PCL Error Codes
The following tables list error codes that could appear on the printer message window 
when running the HP-GL, PCL or HPXL emulation. 
HP-GL PCL
Error 
CodeDescription Error 
CodeDescription
0 Not enough memory for job. 0 Not enough memory for job.
1 Too many transformations. 1 State lost.
2 Math error. 2 Math error.
3 Job aborted. 3 Job aborted.
4 Instruction not recognized. 4 Out of memory for macros.
5 Wrong number of...

Additional Assistance 97
PostScript Errors
If your printer is having trouble printing when using PostScript emulation, you should turn 
on the Error Handler in the control panel menu. Error Handler is a diagnostic tool that 
identifies PostScript errors encountered during a print job.
Additional Assistance
If you’ve followed all of the instructions in this guide and still have problems you can’t 
solve, refer to the Service & Support Guide
 or visit our web site at www.minolta-qms.com 
for current...

Downloaded From ManualsPrinter.com Manuals 

5
Installing Other
Accessories
Downloaded From ManualsPrinter.com Manuals 

Introduction 100
Introduction
The optional lower feeder unit and duplex unit were discussed in the Installation Guide
. 
This chapter provides information about the following accessories. Contact your local 
vendor for purchase information.
5-bin Mailbox
Three models: For 100-, 120-, or 220-volt printers
BuzzBox
Via parallel connection for 100, 120, and 220 volts
Dual In-Line 
Memory Modules 
(DIMMs)Additional memory must be 32, 64, or 128 MB, PC-100 Compliant 
SDRAM DIMMs, up to a printer maximum of 384...