Lucent Technologies TransTalk9000 Digital Wireless System MDW 9031/9031DCP Wireless Pocket Phone Installation And Use Manual

Handset 3  Using the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
74
Line Status IndicatorsThere are 12 status indicators; each one corresponds to a specific outside line or 
programmable/intercom/drop button. (The function of these status indicators varies, 
depending on the communications system you are using—see the Button Mapping 
topic for the appropriate communications system switch in Chapter 6, “MDW 
9031/9031DCP...

Handset 
75
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
3  Using the MDW 9031/9031DCP
Pocket Phone
Low Battery IndicatorThe standard battery pack has approximately three hours of continuous talk time after 
being fully charged. The optional extended battery pack has approximately eight 
hours of continuous talk time after being fully charged.
When the handset is On and the battery power is low, the handset will emit two beeps 
and the Battery icon in...

Handset 3  Using the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
76
Attaching the Metal 
Carrying ClipsTo attach the metal carrying clip to the battery pack, do the following:
1  Remove the battery pack from the handset, as described in “Inserting and 
Removing the Handsets Battery Pack” in Chapter 2.
2  Place the two metal tabs on the clip into the slots on the battery pack, with the 
“hooks” toward the bottom of the...

Handset 
77
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
3  Using the MDW 9031/9031DCP
Pocket Phone
4  Latch the right edge of the clip into the corresponding groove on the inner side of 
the battery pack.
5  Push the left edge of the belt clip and snap it into the corresponding groove on the 
inner side of the battery pack.
6  Reinsert the battery pack in the handset, as described in “Inserting and Removing 
the Handset’s Battery Pack” in Chapter 2....

Handset 3  Using the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
78
•Line Preselection
•Backlighting
•Alerter
Local Mode also gives you access to Local Test Mode (which enables you to test the alerter, vibrator, and 
display) and Wireless Test Mode (which enables you to test sound clarity, signal strength, and voice quality). 
While in Local Mode, the MDW 9031/9031DCP can still receive notification of incoming calls.
To...

Handset 
79
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
3  Using the MDW 9031/9031DCP
Pocket Phone
3  While still holding , press O.
The handset beeps twice, and the display shows the handset settings, indicating 
that you are now in Local Mode. (While in Local Mode, the MDW 
9031/9031DCP can still receive notification of incoming calls.)
If the vibrator is enabled, the VIBR icon appears in the display. For example:
If the vibrator is disabled, no...

Handset 3  Using the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
80
3  While still holding , press O.
The handset beeps twice, and the display shows the handset settings, indicating 
you are in Local Mode. (While in Local Mode, the MDW 9031/9031DCP can still 
receive notification of incoming calls.)
If Line Preselection is enabled, PSEL appears on the top line of the display. For 
example:
If Line Preselection is...

Handset 
81
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
3  Using the MDW 9031/9031DCP
Pocket Phone
Enabling or Disabling 
the AlerterThe alerter is an audible signal to notify you of an incoming call. If a call comes in 
while the phone is idle, the handset rings. If you are already on a call, the handset 
chirps softly. You can adjust the volume of the alerter by pressing the “+” button or 
the “-” button on the side of the handset when the phone is...

Handset 3  Using the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
82
Test Modes
You can use Local Test Mode and Wireless Test Mode to verify that your handset is working properly and that 
the MDW 9031/9031DCP System is performing optimally.
Using Local Test Mode
You can use Local Test Mode to activate the audio warning signal, the vibrator, and all visual indicators on the 
handset display, enabling you to test the...

Handset 
83
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
3  Using the MDW 9031/9031DCP
Pocket Phone
Using Wireless Test Mode
You can determine sound clarity, signal strength, and voice quality using Wireless Test Mode.
You should use Wireless Test Mode to help you locate the best place to install the radio module(s) to optimize the 
performance of your MDW 9031/9031DCP Pocket Phone. Repeat the tests several times, with the radio module 
positioned in a...