Lucent Technologies TransTalk9000 Digital Wireless System MDW 9031/9031DCP Wireless Pocket Phone Installation And Use Manual

Installing a Single Carrier 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
34
8  Insert the free end of the telephone line cord into the appropriate extension jack or 
terminal/station connector on your communications system switch/control unit 
(refer to your communications system manual for the proper location).
9  Insert the carrier’s AC adapter cord into the left side of the carrier.
MODULE206
PFT
PFTE...

Installing a Single Carrier 
35
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
10  Place the carrier on its feet towards the back of the shelf or desk, making sure it is 
in a stable position. Be sure the telephone line cords come out the rear exit slots in 
the back of the unit. Arrange the power cord and telephone line cords beneath the 
shelf or desk, so no one can step on them or trip over them.
11...

Installing a Single Carrier 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
36
Installing a Single Carrier on a Wall
•Install the unit high on a wall, leaving 6 to 12 inches (15.2 to 30.5 cm) between 
the top of the antenna and the ceiling.
•Never install or remove a radio module from a carrier that is plugged into a wall 
outlet (hot insertion).
•See “Key Components” earlier in this chapter for additional...

Installing a Single Carrier 
37
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
4  Remove the plastic cap covering each radio module’s card edge before inserting 
the radio modules into the carrier.
5  Starting from the leftmost slot (#1), insert each radio module into the carrier by 
hooking it onto the radio module mounting rod. Slowly swing the radio modules 
card edge into the card edge connector on the...

Installing a Single Carrier 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
38
7  Insert a telephone line cord into the bottom of each radio module.
8  Slide the telephone line cords through the cable manager slot on the left front of 
the carrier.
9  Insert the free end of each telephone line cord into the appropriate extension jack 
or terminal/station connector on your communications system switch/control...

Installing a Single Carrier 
39
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
10  Plug the carrier’s AC adapter cord into the left side of the carrier.
11  Insert the carrier’s power cord into the AC adapter, then plug the power cord into 
a properly grounded, 3-prong wall outlet that is not controlled by an on/off 
switch.
If appropriate, you can wall-mount the AC adapter using its attached wall-
mounting...

Installing a Single Carrier 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
40
Single Carrier Installation Self-Test
To perform a single carrier self-test:
1  A single carrier must always function as a control carrier. Wait a few seconds, 
then check the LED(s) on the right side of the carrier:
~Model 117A4: 
Compare the OUT OF SYNC and CONTROL/EXPANSION LEDs against 
the top three lines on the “SYNC and...

Installing Multiple Carriers 
41
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
3  If you are using a Model 117A4 carrier, verify that the carrier’s 
CONTROL/EXPANSION LED is lit and that its color is green. This is correct 
for a single-carrier installation.
4  Verify that the POWER and PA S S LEDs on each radio module are lit. If a radio 
module’s PA S S LED does not light, power down the carrier and the...

Installing Multiple Carriers 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
42
Multiple-carrier installation involves several stages:
•Mounting the carriers on the wall and cabling them.
•Installing a single radio module in each carrier.
•Installing the remaining radio modules.
The most efficient method for installing carriers and their radio modules is to perform self-tests after each stage 
of the...

Installing Multiple Carriers 
43
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
4  Place the carrier assembly over the screws, then slide it downward to lock it into 
place. Be sure that the leftmost carrier is the control carrier. Tighten the screws. 
Repeat for each carrier.
5  Connect an expansion cable to the OUT jack of the control carrier.
6  Insert the free end of the expansion cable into the IN jack...