Lucent Technologies TransTalk9000 Digital Wireless System MDW 9031/9031DCP Wireless Pocket Phone Installation And Use Manual

Installing Multiple Carriers 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
54
Installing the Remaining Radio Modules
To install the remaining radio modules:
1  Power down the carriers.
2  Remove the plastic cap covering each radio module’s card edge before inserting 
the radio modules into the carriers.
3  Beginning with the first empty slot and working from left to right, insert a radio 
module into each...

Installing Multiple Carriers 
55
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
4  When the card edge is fully seated, a snap lock on the bottom of the radio module 
will engage.
5  Repeat Steps 3 and 4 for each expansion carrier, until each radio module is 
inserted into a carrier.
Note:Fill all six slots of the current carrier before inserting radio modules into 
the next carrier.
6  Insert a telephone...

2  Installing the MDW 9031/9031DCP Pocket Phone  Installing Multiple Carriers
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use 503-801-166 56 Issue 3 October 1999
7  Slide the telephone line cords through the cable manager slot on the left front of 
the carrier.
8  Insert the free end of each telephone line cord into the appropriate extension jack 
or terminal/station connector on your communications system switch/control unit 
(refer to your communications system manual for the proper...

Installing Multiple Carriers 
57
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
9  Power the carriers as follows:
!CAUTION:
Never connect or disconnect expansion cables or telephone line cords, or 
insert or remove radio modules, while the carrier is plugged into the wall 
outlet.
10  Go to “Installation Self-Test for Remaining Radio Modules” (page 58).
If the carriers are plugged 
into...
Then...
one surge...

Installing Multiple Carriers 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
58
Installation Self-Test for Remaining Radio Modules
To perform an installation self-test for the remaining radio modules:
1  Wait a few seconds after powering up the carriers, then verify that the carriers’
OUT OF SYNC LEDs are not lit.
2  At this stage of your installation, again verify that the LEDs displayed match the 
first or...

Installing Multiple Carriers 
59
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
3  If an OUT OF SYNC LED is lit, power down, wait at least 15 seconds, and then 
repower the carriers in order from left to right, as described in Step 9 in 
“Installing the Remaining Radio Modules.” If the LED is still lit, follow the 
suggestions in the “Installation Problems” section of Chapter 5, 
“Troubleshooting.” If the...

Handset 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
60
Handset
This section explains how to install the handset battery pack, change the communications system setting, and fill 
out the handset label.
Inserting and Removing the Handset’s Battery Pack
To insert and remove the battery pack:
1  To insert the battery pack into the handset, insert the two small rectangular tabs 
located along the bottom back...

Handset 
61
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
3  To remove the battery pack, slide the spring latch upward (away from the battery 
pack). While holding the latch up, grasp both sides of the battery pack, then 
gently pull the battery pack upward and out.
Changing the Communications System Setting
The communications system you use determines what information the MDW 9031/9031DCP Pocket Phone can...

Handset 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
62
4  Press and hold “M” (6) for three seconds to enter Button Mapping Mode.
The handset display shows one of the following:
5  Press   repeatedly to cycle through the settings until the display appropriate 
for your communications system is shown.
6  Press O when the correct setting is displayed.
The top line of the display shows information...

Handset 
63
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
Filling Out the Handset Label
MDW 9031/9031DCP Pocket Phone display shows the status of up to 12 lines or programmable/intercom/drop 
buttons. Since the MDW 9031/9031DCP is compatible with several different communications systems, diagrams 
of the button mappings for these systems are provided in Chapter 6.
MDW 9031/9031DCP has a label on the back...