Lucent Technologies TransTalk9000 Digital Wireless System MDW 9031/9031DCP Wireless Pocket Phone Installation And Use Manual

							Installing Multiple Carriers 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
54
Installing the Remaining Radio Modules
To install the remaining radio modules:
1  Power down the carriers.
2  Remove the plastic cap covering each radio module’s card edge before inserting 
the radio modules into the carriers.
3  Beginning with the first empty slot and working from left to right, insert a radio 
module into each slot of the control carrier. Hook each radio module onto a 
mounting rod. Slowly swing the radio module’s card edge into the card edge 
connector on the back of the carrier.
Note:Slot 6 of a Model 117A3 control carrier must always contain a radio 
module to pass the synchronization signal to the next carrier.
A Model 117A4 carrier does not require Slot 6 to be filled. 
						

							Installing Multiple Carriers 
55
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
4  When the card edge is fully seated, a snap lock on the bottom of the radio module 
will engage.
5  Repeat Steps 3 and 4 for each expansion carrier, until each radio module is 
inserted into a carrier.
Note:Fill all six slots of the current carrier before inserting radio modules into 
the next carrier.
6  Insert a telephone line cord into the bottom of each radio module. 
						

							2  Installing the MDW 9031/9031DCP Pocket Phone  Installing Multiple Carriers
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use 503-801-166 56 Issue 3 October 1999
7  Slide the telephone line cords through the cable manager slot on the left front of 
the carrier.
8  Insert the free end of each telephone line cord into the appropriate extension jack 
or terminal/station connector on your communications system switch/control unit 
(refer to your communications system manual for the proper location).
MODULE206
PFT
PFTE
X
T
E
N
S
I
O
N
SL
I
N
E
SMODULE206
PFT
PFTE
X
T
E
N
S
I
O
N
SL
I
N
E
S
PFTL
I
N
E
S
MODULE400
PFTL
I
N
E
S
MODULE400
PFTL
I
N
E
SPROCESSOR
MODULEMUSIC
ON
HOLDVOL
PAGE
E
X
T
E
N
S
I
O
N
SE
X
T
E
N
S
I
O
N
S
SMDR
MUSIC
ON
HOLD
N
S
I
O
N
SX
T
E
N
S
I
O
N
S 
						

							Installing Multiple Carriers 
57
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
9  Power the carriers as follows:
!CAUTION:
Never connect or disconnect expansion cables or telephone line cords, or 
insert or remove radio modules, while the carrier is plugged into the wall 
outlet.
10  Go to “Installation Self-Test for Remaining Radio Modules” (page 58).
If the carriers are plugged 
into...
Then...
one surge suppressor strip Power the strip.
Result: All the carriers will turn on simultaneously.
wall outletsPlug in the power for the carriers in this order:
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
Control
Carrier
1
Expansion
Carrier #1Expansion
Carrier #2
23
12346
TRANSTALK
2 1O   N2 1O   N
5
CAU
TIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
Expansion
Carrier #3
4
MNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLOMNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLOMNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLOMNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLO
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUT
IONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
Expansion
Carrier #4
5
MNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLO 
						

							Installing Multiple Carriers 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
58
Installation Self-Test for Remaining Radio Modules
To perform an installation self-test for the remaining radio modules:
1  Wait a few seconds after powering up the carriers, then verify that the carriers’
OUT OF SYNC LEDs are not lit.
2  At this stage of your installation, again verify that the LEDs displayed match the 
first or fourth lines of the SYNC and CONTROL/EXP LED Codes label, 
depending on whether the carrier is the control or an expansion carrier. (Keep in 
mind that a Model 117A3 carrier does not have a CONTROL/EXPANSION 
LED.)
12346
4TRANSTALK
2 1O   N2 1O   N
5
CAUTIONUSE 
ONLY
AT&T 
CABLE
P⁄N 
847667896I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
M
N
N
O
E
A
P
T
R
H
A
N
H
A
P
T
E
R
G
R
R
E
P
R
A
C
I
T
E
-
O
KL
O
R
E
M
I
P
S
U
MR
E
P
R
A
C
I
T
E
-
O
KR
E
P
R
A
C
I
T
E
-
O
KX
E
R
T
F
A
M
R
U
K
L
A
R
I
E
N
L
OR
E
P
R
A
C
I
T
E
-
O
KL
O
R
E
M
I
P
S
U
MX
E
R
T
F
A
M
R
U
K
L
A
R
I
E
N
L
O
OUT OF SYNC
CONTROL/
EXPANSION 
						

							Installing Multiple Carriers 
59
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
3  If an OUT OF SYNC LED is lit, power down, wait at least 15 seconds, and then 
repower the carriers in order from left to right, as described in Step 9 in 
“Installing the Remaining Radio Modules.” If the LED is still lit, follow the 
suggestions in the “Installation Problems” section of Chapter 5, 
“Troubleshooting.” If the LED is still lit, call Customer Support as described in 
the Copyright and Legal Notices at the beginning of this book.
4  The PA S S and POWER LEDs on all radio modules should be lit and green, 
indicating that all of the radio modules are functional. If a radio module’s PA S S 
LED is not lit:
 a  Power down the carriers.
 b  From the wall outlet, unplug the power cord/AC adapter of the radio module 
that did not light.
 c  Wait 15 seconds.
 d  Plug in the radio module’s power cord again.
 e  Repower the carriers, following the proper left-to-right order.
If the PA S S LED is still not lit, follow the suggestions in the “Installation 
Problems” section of Chapter 5, “Troubleshooting.” If the LED is still not lit, 
call Customer Support as described in the Copyright and Legal Notices at the 
beginning of this book.
5  Go to “Handset” (page 60).
12346
4TRANSTALK
2 1O   N2 1O   N
5
CAUTIONUSE 
ONLY
AT&T 
CABLE
P⁄N 
847667896I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
M
N
N
O
E
A
P
T
R
H
A
N
H
A
P
T
E
R
G
R
R
E
P
R
A
C
I
T
E
-
O
KL
O
R
E
M
I
P
S
U
MR
E
P
R
A
C
I
T
E
-
O
KR
E
P
R
A
C
I
T
E
-
O
KX
E
R
T
F
A
M
R
U
K
L
A
R
I
E
N
L
OR
E
P
R
A
C
I
T
E
-
O
KL
O
R
E
M
I
P
S
U
MX
E
R
T
F
A
M
R
U
K
L
A
R
I
E
N
L
O
OUT OF SYNC
CONTROL/
EXPANSION
P
O
W
E
RR
A
D
IOPASS
Radio 
Module
POWER
RADIO
PASS 
						

							Handset 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
60
Handset
This section explains how to install the handset battery pack, change the communications system setting, and fill 
out the handset label.
Inserting and Removing the Handset’s Battery Pack
To insert and remove the battery pack:
1  To insert the battery pack into the handset, insert the two small rectangular tabs 
located along the bottom back edge of the handset into the two rectangular holes 
along the bottom front edge of the battery pack.
2  Press the battery pack downward until it clicks into place.
The battery pack must be charged prior to using the handset. See “Battery 
Charger” later in this chapter for instructions.
Rectangular tabs
Spring latch 
						

							Handset 
61
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
3  To remove the battery pack, slide the spring latch upward (away from the battery 
pack). While holding the latch up, grasp both sides of the battery pack, then 
gently pull the battery pack upward and out.
Changing the Communications System Setting
The communications system you use determines what information the MDW 9031/9031DCP Pocket Phone can 
display and how the phone lines and programmable/intercom/drop buttons are identified. (For the MDW 9031, 
see the appropriate “Button Mapping” topics in the “MDW 9031 Compatibility” section in Chapter 6. For the 
MDW 9031DCP, see the “Button Mapping” topic in the “MDW 9031DCP Compatibility” section in Chapter 6.)
The MDW 9031 is factory-set to work with the PARTNER communications system. If you are using 
PARTNER as your communications system, skip this section; if you are using a different communications 
system, you will need to change the setting.
The MDW 9031DCP is factory-set to work with the DEFINITY communications system.
To change the communications system setting, use the following procedure to enter Local Mode and then Button 
Mapping Mode:
1  Make sure the handset is turned off.
2  Press and hold the Select button (  ) for three seconds.
3  While still holding , press O.
The handset beeps twice, and the top line of the display shows LCL:P (unless you 
have already changed it from the default setting). 
						

							Handset 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
62
4  Press and hold “M” (6) for three seconds to enter Button Mapping Mode.
The handset display shows one of the following:
5  Press   repeatedly to cycle through the settings until the display appropriate 
for your communications system is shown.
6  Press O when the correct setting is displayed.
The top line of the display shows information appropriate to the communications 
system you are using.
7  To verify your setting, repeat Steps 1–3. The top line of the display should appear 
as follows, depending upon your communications system:
For a description of the button mapping between the MDW 9031/9031DCP Pocket 
Phone and the wired telephones for your communications system, or to program 
features on buttons, see the appropriate “Button Mapping” topics in Chapter 6.MAP:PPARTNER Systems
MAP:DDEFINITY Systems, System 25, System 75, and 
System 85
Note:The MDW 9031DCP should only be set 
to MAP:D for DEFINITY.
MAP:M1All MERLIN Systems (except MERLIN 410 
and MERLIN 820), including MERLIN LEGEND
MAP:M2MERLIN 410 and MERLIN 820
PARTNER SystemsLCL:P
DEFINITY Systems, System 25, System 75, and 
System 85LCL:D
All MERLIN Systems (except MERLIN 410 and 
MERLIN 820), including MERLIN LEGENDLCL:M1
MERLIN 410 and MERLIN 820LCL:M2 
						

							Handset 
63
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
Filling Out the Handset Label
MDW 9031/9031DCP Pocket Phone display shows the status of up to 12 lines or programmable/intercom/drop 
buttons. Since the MDW 9031/9031DCP is compatible with several different communications systems, diagrams 
of the button mappings for these systems are provided in Chapter 6.
MDW 9031/9031DCP has a label on the back of the handset near the top where you can record:
•Your extension number.
•The mapping of your MDW 9031/9031DCP line buttons to those on a wired 
phone for your communications system.
Note:Use a pencil or ballpoint pen on the label, in case you want to erase the 
information later. Do not use felt-tip or other types of non-erasable 
markers. Also, do not remove the label.
To fill out the handset label:
1  Write your extension number on the label.
2  Locate the section in Chapter 6 that describes the button mapping for your 
communications system; then copy the mapping to the label for ease of reference.
3  Go to “Battery Charger” (page 64). Note:The MDW 9031DCP is compatible only with DEFINITY.
E
X
T
.ABCD1
23
4
5
6
7
8
EXT.AB
C
D123
4
5
6
7
8