Lucent Technologies TransTalk9000 Digital Wireless System MDW 9031/9031DCP Wireless Pocket Phone Installation And Use Manual

							Battery Charger 3  Using the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
94 
						

							95MDW 9031/9031DCP Wireless Pocket Phone Installation and Use503-801-166 — Issue 3 — October 1999   
4 Maintaining the MDW 9031/9031DCP
Pocket Phone
Important Safety Instructions
Please see “Important Safety Instructions” at the beginning of Chapter 2.
Removing Radio Module from Carrier
•Slot 6 of a Model 117A3 control carrier must always contain a radio module to 
pass the synchronization signal to the next carrier.
•See “Key Components” in Chapter 2 for additional picture detail.
To remove a radio module from the carrier:
1  Unplug the carrier(s) power cord/AC adapter from the wall outlet.
Note:When power is disconnected from the radio module or carrier, the 
receiver and alerter volumes are reset to the factory default settings. 
						

							Removing Radio Module from Carrier 4  Maintaining the MDW
9031/9031DCP Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
96
2  Unplug the telephone line cord from the bottom of the radio module.
3  Press up and hold the snap lock on the bottom rear of the radio module.
4  Slowly swing the radio module’s card edge out of the card edge connector on the 
back of the carrier, releasing the snap lock when clear. Unhook the radio module 
from the radio module mounting rod by gently lifting upward. 
						

							Removing Radio Module from Carrier 
97
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
4  Maintaining the MDW
9031/9031DCP Pocket Phone
5  If you removed a radio module from Slot 6 of an 117A3 control carrier, you must 
insert another radio module into this slot. Failure to do so will cause the carriers 
to be unsynchronized.
6  Repower the carrier. If you have multiple carriers, repower them in order from 
left to right, as shown below:
7  Wait a few seconds, then verify that the carrier’s OUT OF SYNC LED is not lit. 
If the LED is lit, power down, wait at least 15 seconds, and then repower the 
carrier. If the LED is still lit, follow the suggestions in the “Installation Problems” 
section of Chapter 5, “Troubleshooting.” If the LED is still lit, call Customer 
Support as described in the Copyright and Legal Notices at the beginning of this 
book.
8  For any Model 117A4 carriers, verify that the CONTROL/EXPANSION LED is 
lit. For the control carrier, this LED is green. For an expansion carrier, this LED is 
amber.
9  Reset the receiver and alerter volumes that reverted to the default settings when 
the system was powered down (see “Changing the Handset Settings” in 
Chapter 3).
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
Control
Carrier
1
Expansion
Carrier #1Expansion
Carrier #2
23
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
Expansion
Carrier #3
4
MNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLOMNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLOMNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLOMNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLO
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
Expansion
Carrier #4
5
MNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLO
12346
4TRANSTALK
2 1O   N2 1O   N
5
CAUTIONUSE 
ONLY
AT&T 
CABLE
P⁄
N 
847667896I
N
O
U
T
O
U
T
 
O
F
 
S
Y
NC
M
N
N
O
E
A
P
T
R
H
A
N
H
A
P
T
E
R
G
R
R
E
P
R
A
C
I
T
E
-
O
KL
O
R
E
M
I
P
S
U
MR
E
P
R
A
C
I
T
E
-
O
KR
E
P
R
A
C
I
T
E
-
O
KX
E
R
T
F
A
M
R
U
K
L
A
R
I
E
N
L
OR
E
P
R
A
C
I
T
E
-
O
KL
O
R
E
M
I
P
S
U
MX
E
R
T
F
A
M
R
U
K
L
A
R
I
E
N
L
O
OUT OF SYNC
CONTROL/
EXPANSION 
						

							Swapping Extensions 4  Maintaining the MDW
9031/9031DCP Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
98
Swapping Extensions
If you want to change your phone’s extension number assignment, make sure the radio module or carrier(s) is 
unplugged before you unplug the telephone line cord from the communications system switch/control unit. 
Power down and then repower the carrier(s) after all extension changes are made.
To swap extensions:
1  Unplug the carrier(s) power cord/AC adapter from the wall outlet.
Note:When power is disconnected from the radio module or carrier, the 
receiver and alerter volumes are reset to the factory default settings.
2  Unplug the telephone line cords from the communications system switch/control 
unit for the extensions that you want to change.
3  Insert the telephone line cords for the extensions that you want to change into the 
desired extension jack or terminal/station connector on your communications 
system switch/control unit.
MODULE206
PFT
PFTE
X
T
E
N
S
I
O
N
SL
I
N
E
SMODULE206
PFT
PFTE
X
T
E
N
S
I
O
N
SL
I
N
E
S
PFTL
I
N
E
S
MODULE400
PFTL
I
N
E
S
MODULE400
PFTL
I
N
E
SPROCESSOR
MODULEMUSIC
ON
HOLDVOL
PAGE
E
X
T
E
N
S
I
O
N
SE
X
T
E
N
S
I
O
N
S
SMDR
MUSIC
ON
HOLD
N
S
I
O
N
SX
T
E
N
S
I
O
N
S 
						

							Swapping Extensions 
99
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
4  Maintaining the MDW
9031/9031DCP Pocket Phone
4  Repower the carrier. If you have multiple carriers, repower them in order from 
left to right, as shown below:
5  Wait a few seconds, then verify that the carrier’s OUT OF SYNC LED is not lit. 
If the LED is lit, power down, wait at least 15 seconds, and then repower the 
carrier. If the LED is still lit, follow the suggestions in the “Installation Problems” 
section of Chapter 5, “Troubleshooting.” If the LED is still lit, call Customer 
Support as described in the Copyright and Legal Notices at the beginning of this 
book.
6  For any Model 117A4 carriers, verify that the CONTROL/EXPANSION LED is 
lit. For the control carrier, this LED is green. For an expansion carrier, this LED is 
amber.
7  Reset the receiver and alerter volumes that reverted to the default settings when 
the system was powered down (see “Changing the Handset Settings” in 
Chapter 3).
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
Control
Carrier
1
Expansion
Carrier #1Expansion
Carrier #2
23
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
Expansion
Carrier #3
4
MNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLOMNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLOMNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLOMNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLO
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
Expansion
Carrier #4
5
MNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLO
12346
4TRANSTALK
2 1O   N2 1O   N
5
CAUTIONUSE ONLY
AT&T CABLE
P⁄
N 847667896IN
O
U
T
O
U
T OF 
SY
NC
MNNOEAPT
RHAN
HAPT
ERGR
REPRACI
T E-
OKL OREMI
PSUMREPRACI
T E-
OKREPRACI
T E-
OKXERT
F AMRU
KL
ARI
ENL
OREPRACI
T E-
OKL OREMI
PSUMXERT
F AMRU
KL
ARI
ENL
O
OUT OF SYNC
CONTROL/
EXPANSION 
						

							Replacing Antenna 4  Maintaining the MDW
9031/9031DCP Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
100
Replacing Antenna
If the antenna on your MDW 9031/9031DCP Pocket Phone handset becomes damaged, you can order a 
replacement antenna (see “Ordering Replacement and Optional Parts” later in this chapter), and replace it 
yourself.
To replace the antenna: 
1  Fully retract the antenna.
2  Grasping the base of the antenna, unscrew it by turning it counterclockwise.
3  Grasping the base of the new antenna, screw it into the handset in a clockwise 
direction.
Ordering Replacement and Optional Parts
To order replacement parts or optional equipment in the continental U.S., call the Lucent Direct or National Parts 
Sales Center toll free. When ordering, please use the part numbers shown in the following table.
Note:The pocket phone accessories listed in this table can be used with the MDW9031, 
MDW 9031DCP, and MDW 9031 Dual Zone Pocket Phones.
ItemLucent Direct
 1-800-451-2100National Parts
Sales Center 
1-800-222-PART
MDW 9031 Pocket Phone (stand-alone); 
includes Radio Module and Kit of Parts3204-07B 108046525 (for Pocket 
Phones) 107586828 (for 
Kit of Parts)
MDW 9031 Pocket Phone System (requires 
carrier); includes Radio Module, but not Kit 
of Parts3204-W7B 108046525
Retractable Flex Antenna for MDW 9031 
Pocket Phone HeadsetNA 847713450
Standard Battery Pack; 
includes Carrying Clip32045A 107733107
MDW 9031DCP Pocket Phone (standalone) 3229-01D 108401514
MDW 9031DCP Pocket Phone System 
(requires carrier)3229-WID 108401514
Standard Battery Metal Carrying Clip 32046 847773140
Standard Battery Plastic Carrying Clip  3204-BCS 848172847
Extended Battery Pack; 
includes Carrying Clip32049A 107733115
Extended Battery Metal Carrying Clip 3204-CLP 847773157
Extended Battery Plastic Carrying Clip 3204-BCX 848441390 
						

							Ordering Replacement and Optional Parts 
101
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
4  Maintaining the MDW
9031/9031DCP Pocket Phone
Outside the continental U.S., contact your Lucent Technologies Representative or local Authorized Dealer.Lanyard NA 407183417
MDW 9031 Pocket Phone 
Leather Carrying Case32043A 847877487
MDW 9031 Pocket Phone 
Leather Carrying Case 
customized for headset use32090A 848026092
Battery Charger; includes Power Cord/AC 
Adapter3279-3BC 108386921
Power Cord/AC Adapter for Battery 
Charger [11 foot (3.4 m)]NA 408082204
Carrier; includes:
Power Cord and AC Adapter for Carrier
[25 foot (7.6 m)]
Expansion Cable for Multiple-Carrier 
Installation [6 foot (1.8 m)]3204-CR3A 107907289 
(for 117A3)
107955122
(for 117A4)
Power Cord and AC Adapter for Carrier
[25 foot (7.6 m)]NA 847224227
Expansion Cable for Multiple-Carrier 
Installation [6 foot (1.8 m)]32035A 847667870
Telephone Line Cord [8 foot (2.4 m)] NA 103786794
Supra Binaural Headset (no Adapter) 3275-SU2 409094746
Supra 9031 Headset with 
Quick Disconnect Adapter3275-042/A 407713718
(for Headset)
848047965
(for Adapter)
MDW 9031 Adapter for 
Supra Binaural and Supra 9030/9031 
Headsets3204-ADP 848047965
Radium (Over-the-Ear) Headset 
with Adapter3275-042/A 407720739
(for Headset)
848047965
(for Adapter)
Kit of Parts (for stand-alone installations); 
includes Power Cord/AC Adapter for Radio 
Module [11 foot (3.4 m)]D-182866 107586828 ItemLucent Direct
 1-800-451-2100National Parts
Sales Center 
1-800-222-PART 
						

							Ordering Replacement and Optional Parts 4  Maintaining the MDW
9031/9031DCP Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
102 
						

							103MDW 9031/9031DCP Wireless Pocket Phone Installation and Use503-801-166 — Issue 3 — October 1999   
5 Troubleshooting
Procedures
If you have a problem with your MDW 9031/9031DCP Pocket Phone, you may be able to solve it by following 
the procedures included in this chapter. If you cannot resolve the problem, call Customer Support as described in 
the Copyright and Legal Notices at the beginning of this book.
The problems in this chapter are organized as follows:
•Installation
•Handset
•Battery
•Voice Quality
•Range
•Battery Charger