Lucent Technologies TransTalk9000 Digital Wireless System MDW 9031/9031DCP Wireless Pocket Phone Installation And Use Manual

							Installing Multiple Carriers 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
44
8  Plug an AC adapter cord into the left side of each carrier.
9  Insert each carrier’s power cord into its AC adapter.
If appropriate, you can wall-mount each AC adapter using its attached wall-
mounting bracket.
12345 
						

							Installing Multiple Carriers 
45
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
10  Plug each carrier’s power cord into one of the following power sources that is not 
controlled by an on/off switch:
~Surge-suppressor strip.
~Properly grounded, 3-prong wall outlets. (See “wall outlets” in the following 
chart for the order in which to power up the carriers.)
11  Power the carriers as follows:
!CAUTION:
Never connect or disconnect expansion cables or telephone line cords, or 
insert or remove radio modules, while the carrier is plugged into the wall 
outlet.
12  Go to “Multiple Carrier Mounting and Cabling Self-Test” (page 46).
If the carriers are plugged 
into...
Then...
one surge suppressor strip Power the strip.
Result: All the carriers will turn on simultaneously.
wall outletsPlug in the power for the carriers in this order:
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
Control
Carrier
1
Expansion
Carrier #1Expansion
Carrier #2
23
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
Expansion
Carrier #3
4
MNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLOMNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLOMNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLOMNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLO
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
Expansion
Carrier #4
5
MNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLO 
						

							Installing Multiple Carriers 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
46
Multiple Carrier Mounting and Cabling Self-Test
To perform a multiple carrier mounting and cabling self-test:
1  Wait a few seconds after powering up the carriers, then verify that the red OUT 
OF SYNC LEDs on all carriers are lit. This is normal when no radio modules 
have yet been installed. The CONTROL/EXPANSION LEDs (Model 117A4 
only) should also be lit and blinking:
~Model 117A4 control carrier = green blinking
~Model 117A4 expansion carrier(s) = green blinking
A Model 117A3 carrier has no CONTROL/EXPANSION LED, but the DIP 
switch in Slot 4 of the carrier must be set correctly to either Control or Expansion.
2  The following illustration shows the correct LED status for a five-carrier 
installation with no radio modules installed. This sample installation has four 
117A4 carriers—one acting as the control carrier and the other three acting as 
expansion carriers—and one 117A3 carrier acting as an expansion carrier.
12346
4TRANSTALK
2 1O   N2 1O   N
512346
4TRANSTALK
2 1O   N2 1O   N
512346
4TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 
O
N
L
Y
A
T
&
T
 
C
A
B
L
E
P
⁄
N
 
8
4
7
6
6
7
8
9
6IN
O
U
T
O
U
T O
F S
Y
N
C
Control
Carrier
Model
117A4Model
117A4Model
117A3Model
117A4 Expansion
Carrier #1Expansion
Carrier #2
12346
4TRANSTALK
2 1O   N2 1O   N
5
Expansion
Carrier #3
MNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OK
XERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLOMNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OK
XERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLOMNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OK
XERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLO
C
A
U
T
I
O
NUSE 
ONLY
AT&T 
CABLE
P⁄
N 
847667896IN
OUT
OUT OF SYNC
CONTROL/
EXPANSIONC
A
U
T
I
O
NUSE 
ONLY
AT&T 
CABLE
P⁄
N 
847667896IN
OUT
OUT OF SYNC
CONTROL/
EXPANSIONC
A
U
T
I
O
NUSE 
ONLY
AT&T 
CABLE
P⁄
N 
847667896IN
OUT
OUT OF SYNC
CONTROL/
EXPANSION
(DIP switch
 in Slot 4 set to 
Expansion) OUT OF SYNC (red)CONTROL/
EXPANSION OUT OF SYNC (red)
(green)CONTROL/
EXPANSION OUT OF SYNC (red)
(green)CONTROL/
EXPANSION OUT OF SYNC (red)
(green)
123
4
2 1O   N
Model
117A4
46
TRANSTALK
2 1O   N
5
Expansion
Carrier #4
MNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OK
XERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLO
C
A
U
T
I
O
NUSE 
ONLY
AT&T 
CABLE
P⁄
N 
847667896IN
OUT
OUT OF SYNC
CONTROL/
EXPANSION
CONTROL/
EXPANSION OUT OF SYNC (red)
(green) 
						

							Installing Multiple Carriers 
47
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
3  At this stage of your installation, verify the LEDs displayed match the third of the 
SYNC and CONTROL/EXP LED Codes label, depending on whether the carrier 
is the control or an expansion carrier.
4  If the LEDs on your installation do not reflect this pattern, there is probably a 
mistake in the cabling. Power down the carriers and check that you have correctly 
followed Steps 6 through 8 in “Mounting and Cabling Multiple Carriers.” If you 
are still having problems, see Chapter 5, “Troubleshooting.”
5  If your LEDs match the pattern in the illustration, you can feel confident that your 
carriers are cabled correctly.
6  Go to “Installing a Single Radio Module in Each Carrier” (page 48). 
						

							Installing Multiple Carriers 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
48
Installing a Single Radio Module in Each Carrier
To install a single radio module in each carrier:
1  Power down the carriers.
2  Remove the plastic cap covering each radio module’s card edge before inserting 
the radio modules into the carriers.
3  Working from left to right, insert a radio module into the first slot (Slot 1) of each 
carrier; hook each radio module onto the mounting rod. Slowly swing the radio 
module
’s card edge into the card edge connector on the back of the carrier. 
(Exception: use Slot 6 instead of Slot 1 for a Model 117A3 control carrier.)
Note:Slot 6 of a Model 117A3 control carrier must always contain a radio 
module to pass the synchronization signal to the next carrier.
A Model 117A4 carrier does not require Slot 6 to be filled. 
						

							Installing Multiple Carriers 
49
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
4  When the card edge is fully seated, a snap lock on the bottom of the radio module 
will engage.
5  Insert a telephone line cord into the bottom of each radio module.
6  Slide the telephone line cords through the cable manager slot on the left front of 
each carrier.
   
						

							Installing Multiple Carriers 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
50
7  Insert the free end of each telephone line cord into the appropriate extension jack 
or terminal/station connector on your communications system switch/control unit 
(refer to your communications system manual for the proper location).
8  Power the carriers as follows:
!CAUTION:
Never connect or disconnect expansion cables or telephone line cords, or 
insert or remove radio modules, while the carrier is plugged into the wall 
outlet.
Keep in mind that a Model 117A3 control carrier must have a module in Slot 6 in 
order to synchronize correctly with the remaining carrier(s).
9  Go to “Installation Self-Test with a Single Radio Module in Each Carrier” (page 
51).
MODULE206
PFT
PFTE
X
T
E
N
S
I
O
N
SL
I
N
E
SMODULE206
PFT
PFTE
X
T
E
N
S
I
O
N
SL
I
N
E
S
PFTL
I
N
E
S
MODULE400
PFTL
I
N
E
S
MODULE400
PFTL
I
N
E
SPROCESSOR
MODULEMUSIC
ON
HOLDVOL
PAGE
E
X
T
E
N
S
I
O
N
SE
X
T
E
N
S
I
O
N
S
SMDR
MUSIC
ON
HOLD
N
S
I
O
N
SX
T
E
N
S
I
O
N
S
If the carriers are plugged 
into...
Then...
one surge suppressor strip Power the strip.
Result: All the carriers will turn on simultaneously.
wall outletsPlug in the power for the carriers in this order:
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
Control
Carrier
1
Expansion
Carrier #1Expansion
Carrier #2
23
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
Expansion
Carrier #3
4
MNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLOMNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLOMNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLOMNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLO
12346
TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
Expansion
Carrier #4
5
MNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OKXERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLO 
						

							Installing Multiple Carriers 
51
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
Installation Self-Test with a Single Radio Module in Each Carrier
To perform an installation self-test with a single radio module in each carrier:
1  Wait a few seconds after powering up the carriers, then verify that the carriers’ 
OUT OF SYNC LEDs are not lit.
2  The following illustration shows the correct LED lights for a five-carrier 
installation with one radio module installed in each carrier. This sample 
installation has four 117A4 carriers—one acting as the control carrier and the 
other three acting as expansion carriers—and one 117A3 carrier acting as an 
expansion carrier.
When correct installation procedures are followed and one radio module is 
present in each carrier, the red OUT OF SYNC LEDs will not be lit on any 
carrier, no matter which model. The other LEDs will be lit as follows:
~Model 117A4 control carrier CONTROL/EXPANSION LED = green
~Three Model 117A4 expansion carriers CONTROL/EXPANSION LED = 
amber
~The radio modules’ PA S S and POWER LEDs = green
The Model 117A3 expansion carrier has no CONTROL/EXPANSION LED, but 
the DIP switch in Slot 4 of the carrier is set to Expansion.
12346
TRANSTALK
2 1O   N2 1O   N
512346
TRANSTALK
2 1O   N2 1O   N
512346
TRANSTALK
2 1O   N2 1O   N
5
Control
Carrier
Model
117A4Model
117A4Model
117A3Model
117A4 Expansion
Carrier #1Expansion
Carrier #2
12346
TRANSTALK
2 1O   N2 1O   N
5
Expansion
Carrier #3
U
S
E
 
O
N
L
Y
A
T
&
T
 
C
A
B
L
E
P
⁄
N
 
8
4
7
6
6
7
8
9
6
MNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OK
XERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLOMNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OK
XERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLOMNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OK
XERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLO
C
A
U
TIO
NUSE 
ONLY
AT&T 
CABLE
P⁄
N 
847667896I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
C
O
N
T
R
O
L
/
E
X
P
A
N
S
I
O
NC
A
U
T
IO
NUSE 
ONLY
AT&T 
CABLE
P⁄
N 
847667896I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
C
O
N
T
R
O
L
/
E
X
P
A
N
S
I
O
NC
A
U
TIO
NUSE 
ONLY
AT&T 
CABLE
P⁄
N 
847667896I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
C
O
N
T
R
O
L
/
E
X
P
A
N
S
I
O
N
POWERRADIOPASS
C
A
U
T
IO
NO
U
T I
N
O
U
T
 
O
F
 
S
Y
N
C
POWERRADIOPASS
POWERR
A
D
IOPA S
S
POWERRADIOPASSPOWERRADIOPASS
CONTROL/
EXPANSION OUT OF SYNC
(green)CONTROL/
EXPANSION OUT OF SYNC
(amber)(DIP switch
 in Slot 4 set to 
Expansion) OUT OF SYNC(amber)
CONTROL/
EXPANSION OUT OF SYNC
Model
117A4
12346
TRANSTALK
2 1O   N2 1O   N
5
Expansion
Carrier #4
MNNOEAPTRHAN
HAPTERGR
REPRACITE-OKLOREMIPSUMREPRACITE-OKREPRACITE-OK
XERTFAMRU
KLARIENLOREPRACITE-OKLOREMIPSUMXERTFAMRU
KLARIENLO
C
A
U
TIO
NUSE 
ONLY
AT&T 
CABLE
P⁄
N 
847667896I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
C
O
N
T
R
O
L
/
E
X
P
A
N
S
I
O
N
POWERRADIOPASS
(amber)
CONTROL/
EXPANSION OUT OF SYNC 
						

							Installing Multiple Carriers 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
52
3  At this stage of your installation, verify that the LEDs displayed match the first or 
fourth lines of the SYNC and CONTROL/EXP LED Codes label.
4  If an OUT OF SYNC LED is lit, power down, wait at least 15 seconds, and then 
repower the carriers in order from left to right, as described in Step 8 in 
“Installing a Single Radio Module in Each Carrier.” If the LED is still lit, follow 
the suggestions in the “Installation Problems” section of Chapter 5, 
“Troubleshooting.” If the LED is still lit, call Customer Support as described in 
the Copyright and Legal Notices at the beginning of this book.
12346
4TRANSTALK
2 1O   N2 1O   N
5
CAUTIONUSE 
ONLY
AT&T 
CABLE
P⁄N 
847667896I
N
O
U
T
O
U
T
 
O
F
 
S
Y
N
C
M
N
N
O
E
A
P
T
R
H
A
N
H
A
P
T
E
R
G
R
R
E
P
R
A
C
I
T
E
-
O
KL
O
R
E
M
I
P
S
U
MR
E
P
R
A
C
I
T
E
-
O
KR
E
P
R
A
C
I
T
E
-
O
KX
E
R
T
F
A
M
R
U
K
L
A
R
I
E
N
L
OR
E
P
R
A
C
I
T
E
-
O
KL
O
R
E
M
I
P
S
U
MX
E
R
T
F
A
M
R
U
K
L
A
R
I
E
N
L
O
OUT OF SYNC
CONTROL/
EXPANSION 
						

							Installing Multiple Carriers 
53
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
5  The PA S S and POWER LEDs on all radio modules should be lit and green. If a 
radio module’s PA S S LED is not lit:
 a  Power down the carriers.
 b  From the wall outlet, unplug the power cord/AC adapter of the radio module 
that did not light.
 c  Wait 15 seconds.
 d  Plug in the radio module’s power cord again.
 e  Repower the carriers, following the proper left-to-right order.
If the PA S S LED is still not lit, follow the suggestions in the “Installation 
Problems” section of Chapter 5, “Troubleshooting.” If the LED is still not lit, 
call Customer Support as described in the Copyright and Legal Notices at the 
beginning of this book.
6  Verify that LEDs match the pattern in the illustration in Step 2; if so, you can feel 
confident that the carriers are cabled correctly and that the installed radio modules 
are all functional.
7  Go to “Installing the Remaining Radio Modules” (page 54).
PO
W
E
RR
AD
IOPASS
Radio 
Module
POWER
RADIO
PASS