Lucent Technologies TransTalk9000 Digital Wireless System MDW 9031/9031DCP Wireless Pocket Phone Installation And Use Manual

Installing Multiple Carriers 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
44
8  Plug an AC adapter cord into the left side of each carrier.
9  Insert each carrier’s power cord into its AC adapter.
If appropriate, you can wall-mount each AC adapter using its attached wall-
mounting bracket.
12345 

Installing Multiple Carriers 
45
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
10  Plug each carrier’s power cord into one of the following power sources that is not 
controlled by an on/off switch:
~Surge-suppressor strip.
~Properly grounded, 3-prong wall outlets. (See “wall outlets” in the following 
chart for the order in which to power up the carriers.)
11  Power the carriers as follows:
!CAUTION:...

Installing Multiple Carriers 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
46
Multiple Carrier Mounting and Cabling Self-Test
To perform a multiple carrier mounting and cabling self-test:
1  Wait a few seconds after powering up the carriers, then verify that the red OUT 
OF SYNC LEDs on all carriers are lit. This is normal when no radio modules 
have yet been installed. The CONTROL/EXPANSION LEDs (Model...

Installing Multiple Carriers 
47
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
3  At this stage of your installation, verify the LEDs displayed match the third of the 
SYNC and CONTROL/EXP LED Codes label, depending on whether the carrier 
is the control or an expansion carrier.
4  If the LEDs on your installation do not reflect this pattern, there is probably a 
mistake in the cabling. Power down the...

Installing Multiple Carriers 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
48
Installing a Single Radio Module in Each Carrier
To install a single radio module in each carrier:
1  Power down the carriers.
2  Remove the plastic cap covering each radio module’s card edge before inserting 
the radio modules into the carriers.
3  Working from left to right, insert a radio module into the first slot (Slot 1) of...

Installing Multiple Carriers 
49
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
4  When the card edge is fully seated, a snap lock on the bottom of the radio module 
will engage.
5  Insert a telephone line cord into the bottom of each radio module.
6  Slide the telephone line cords through the cable manager slot on the left front of 
each carrier.
   

Installing Multiple Carriers 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
50
7  Insert the free end of each telephone line cord into the appropriate extension jack 
or terminal/station connector on your communications system switch/control unit 
(refer to your communications system manual for the proper location).
8  Power the carriers as follows:
!CAUTION:
Never connect or disconnect expansion cables or...

Installing Multiple Carriers 
51
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
Installation Self-Test with a Single Radio Module in Each Carrier
To perform an installation self-test with a single radio module in each carrier:
1  Wait a few seconds after powering up the carriers, then verify that the carriers’ 
OUT OF SYNC LEDs are not lit.
2  The following illustration shows the correct LED lights for a...

Installing Multiple Carriers 2  Installing the MDW 9031/9031DCP
Pocket Phone
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
 503-801-166 — Issue 3 — October 1999
52
3  At this stage of your installation, verify that the LEDs displayed match the first or 
fourth lines of the SYNC and CONTROL/EXP LED Codes label.
4  If an OUT OF SYNC LED is lit, power down, wait at least 15 seconds, and then 
repower the carriers in order from left to right, as described in Step 8 in 
“Installing a Single...

Installing Multiple Carriers 
53
MDW 9031/9031DCP Wireless Pocket Phone Installation and Use
503-801-166— Issue 3 — October 1999  
2  Installing the MDW 9031/9031DCP
Pocket Phone
5  The PA S S and POWER LEDs on all radio modules should be lit and green. If a 
radio module’s PA S S LED is not lit:
 a  Power down the carriers.
 b  From the wall outlet, unplug the power cord/AC adapter of the radio module 
that did not light.
 c  Wait 15 seconds.
 d  Plug in the radio module’s power cord again.
 e  Repower...