Lucent Technologies PassageWay Service Provider For PARTNER Communications System Getting Started

Installing and Configuring the PassageWay
Service Provider
2-8
The PassageWay Service Provider operates with all versions of the
following PARTNER systems:
 ¾ PARTNER ACS
 ¾ PARTNER Endeavor
 ¾ PARTNER II
 ¾ PARTNER Plus
 ¾ PARTNER
  NOTE:
Throughout this document, the term 
PARTNER is used to refer to
all of the systems listed above.
For caller ID capabilities, you must have:
 ¾ a PARTNER ACS, a PARTNER Endeavor, or a PARTNER II Release
3.0 or later system. A PARTNER ACS will provide caller ID (if...

Installing and Configuring the PassageWay
Service Provider
2-9
Before You Begin
Before installing the PassageWay Service Provider, you also must know the
following information:
„the version and release of the PARTNER system your company has (for
example, PARTNER ACS R2.0)
„the type of telephone you have
„the extension number of your telephone
„the location and telephone number of each outside line button on your
telephone
„the location of feature buttons on your telephone
„the number of the COM port (for...

Installing and Configuring the PassageWay
Service Provider
2-10
Installing the PassageWay Adapter
This section describes how to connect the PassageWay adapter to your
telephone, your PC, and the line jack. The PassageWay adapter provides an
interface between the serial port on your PC and the Line jack on your
telephone, enabling you to access the PARTNER system from your PC. The
PassageWay adapter has a DB-25 connector for 25-pin serial ports. If you
have a 9-pin serial port on your PC, use the 9-pin to...

Installing and Configuring the PassageWay
Service Provider
2-11
P
h
o
n
eL
in
e
Line Cord
Figure 2-2.  Connecting the Line Cord to the PassageWay Adapter
  4.  Determine the type of serial port (9 pin or 25 pin) you have on your
PC. If you have a 9-pin serial port, you will use the 9-pin to 25-pin
adapter.
  5.  Connect the DB-25 connector on the PassageWay adapter to the
serial (COM) port on your PC. If your PC has a 9-pin serial (COM)
port, connect the 9-pin to 25-pin adapter to the 9-pin serial (COM)...

Installing and Configuring the PassageWay
Service Provider
2-12
    NOTE:
   You can use an RS-232 cable to connect the adapter to the PC
if you do not want to connect the adapter directly to the PC.
  6.  Connect one end of the 7-foot, 2-pair, modular phone cord (D4BU) to
the jack labeled “Phone” on the PassageWay adapter (Figure 2-3).
Ph
on
eL
in
e
Modular Phone 
Cord (D4BU)
Figure 2-3.  Connecting the Modular Phone Cord to the PassageWay
Adapter 

Installing and Configuring the PassageWay
Service Provider
2-13
  7.  Connect the other end of the 7-foot, 2-pair, modular phone cord
(D4BU) to the Line jack on your telephone.
  8.  Check the LED on the PassageWay adapter. The LED is located next
to the Phone and Line jacks on the PassageWay adapter.
   If the red LED is “on,” proceed to Step 9.
   If the red LED is “off,” proceed to the section “PassageWay Adapter
LEDs” in Chapter 4.
  9.  Turn on your PC.
Now, proceed to “Installing the Software.” 

Installing and Configuring the PassageWay
Service Provider
2-14
Installing the Software
This section describes how to install and configure the PassageWay Service
Provider. You can modify the PassageWay Service Provider configuration
information later by running the PassageWay Configurator.
  NOTE:
If you have an earlier version of PassageWay Solution, you must exit
Connect or AT&TConnect (if it is running) before installing the new
PassageWay Service Provider.
To install the PassageWay Service...

Installing and Configuring the PassageWay
Service Provider
2-15
  4.  If you are installing from diskette, insert diskette #1 of the
PassageWay Service Provider software into the diskette drive of your
PC.
   If you are installing from CD-ROM, insert the CD-ROM of the
PassageWay Service Provider into the CD-ROM drive of your PC.
   If you are installing from a shared directory on a network server,
proceed to Step 5.
  5.  Perform one of the following steps:
 ¾ If you have Windows 95 or Windows NT 4.0 or...

Installing and Configuring the PassageWay
Service Provider
2-16
  7.  Choose the Next button.
   The Select Destination Directory dialog box appears. This dialog box
displays the name of the directory where the PassageWay Service
Provider software will be installed by default.
  8.  If the default directory is unacceptable, choose the Browse button
and specify an alternative directory. Otherwise, proceed to Step 9.
  9.  Choose the Next button.
   If you are using Windows 95 or Windows NT 4.0 or later,...

Installing and Configuring the PassageWay
Service Provider
2-17
   If you are using Windows 95 or Windows NT 4.0 or later, the Creating
Application Folder & Short Cuts message box appears.
   If you are using Windows 3.1 or later, the Creating Program Group &
Icons message box appears.
  13.  Choose the OK button.
   The Installation Completed message box appears.
  14.  Choose the Finish button.
   If you are using Windows 95 or Windows 4.0 or later, the PassageWay
Configurator is launched, and it...