Lucent Technologies PassageWay Service Provider For PARTNER Communications System Getting Started

Introduction
1-4
  NOTE:
To determine whether you are using the proper issue of the Getting
Started Guide for the PassageWay Service Provider installed on your
PC, perform the following steps:
 a.  Start the PassageWay Configurator.
¾ If you have Windows 95 or Windows NT 4.0 or later, select
PassageWay Configurator from the application folder that
contains the PassageWay Service Provider. (The default
application folder is 
PassageWay for PARTNER.)
¾ If you have Windows 3.1 or later or Windows for...

Introduction
1-5
User Responsibilities
Before using the PassageWay Service Provider, you should be familiar with
basic Windows functions and procedures. If not, consult your 
Microsoft
Windows Users Guide
.
You also may need to contact your PC vendor for information on configuring
your PC to meet the PassageWay Service Provider requirements.
Conventions Used in This Guide
The following conventions are used in this guide:
„Throughout this guide, telephones are grouped into two different
categories: system...

Introduction
1-6
„Only active windows are displayed.
„The terms option buttons and radio buttons refer to the same object.
„Throughout this guide, the term PARTNER refers to all versions of the
following systems:
 ¾ PARTNER Advanced Communications System (ACS)
 ¾ PARTNER Endeavor
 ¾ PARTNER II
 ¾ PARTNER Plus
 ¾ PARTNER
Getting Help
If you have questions about or problems with the PassageWay Service
Provider that this guide does not resolve, call the Lucent Technologies
National Customer Care Center at 1...

Installing and Configuring
the PassageWay Service
Provider
2
2-1
Overview
This chapter provides the procedures for installing and configuring the
PassageWay Service Provider.
  NOTE:
The appearance of dialog boxes and message boxes in this chapter
may differ from the dialog boxes and message boxes that appear on
your system, depending on the operating system you are using (that is,
Windows NT 4.0 or later, Windows 95, or Windows 3.1 or later). 

Installing and Configuring the PassageWay
Service Provider
2-2
New PassageWay Service Provider
Users
This section applies to new PassageWay Service Provider users. If you have
an existing version of the PassageWay Service Provider or PassageWay
Solution, proceed to the next section, “Upgrading the PassageWay Service
Provider or PassageWay Solution.”
If you are a new PassageWay Service Provider user, perform the following
steps:
  1.  Read the section “PassageWay Service Provider Components” to
make sure...

Installing and Configuring the PassageWay
Service Provider
2-3
Upgrading the PassageWay Service
Provider or PassageWay Solution
This section applies to users who have an earlier version of the PassageWay
Service Provider or PassageWay Solution installed. If you do not have an
existing version of the PassageWay Service Provider or PassageWay Solution
installed, refer to the previous section, “New PassageWay Service Provider
Users.”
If you have an earlier version of the PassageWay Service Provider software...

Installing and Configuring the PassageWay
Service Provider
2-4
PassageWay Service Provider
Components
The PassageWay Service Provider consists of the following components:
„software
„the PassageWay adapter
The PassageWay adapter provides an interface between your
telephone and an available serial (COM) port on your PC by
connecting to the following objects:
 ¾ the Line jack on your telephone
 ¾ the wall jack in your office
 ¾ the serial port on your PC
Figure 2-1 shows the components of the PassageWay...

Installing and Configuring the PassageWay
Service Provider
2-5
DB-25
Connector
PhoneLine
Modular
Jacks
LED
Figure 2-1.  Components of the PassageWay Adapter 

Installing and Configuring the PassageWay
Service Provider
2-6
PassageWay Service Provider
Requirements
The PassageWay Service Provider requires the hardware and software listed
below. Install the required hardware and software before installing the
PassageWay Service Provider software. Note that system performance may
be adversely affected by lower system speeds and lower memory capacities.
„an IBM-PC compatible or PS/2®-compatible PC with the following
hardware:
 ¾ an 80386 or higher processor
 ¾ an...

Installing and Configuring the PassageWay
Service Provider
2-7
„any of the following operating systems:
  NOTE:
Only English (United States) is supported.
 ¾ Microsoft Windows 3.1 or later
 ¾ Microsoft Windows for Workgroups 3.11 or later
  NOTE:
Throughout this document, the phrase 
Windows 3.1 or later is
used to refer to Windows 3.1 or later and Windows for
Workgroups 3.11 or later.
 ¾ Microsoft Windows 95
 ¾ Microsoft Windows NT Server 4.0 or later or Microsoft Windows NT
Workstation 4.0 or later
„a...