Lucent Technologies Intuity CONVERSANT System Version 7.0 Guide

3  
Voice System Administration  System Control
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 127
Diagnose
The Diagnose menu allows you to perform diagnostics on system equipment 
and voice port loop around test.
Diagnose 
Equipment
!
CAUTION:
Run diagnostics on a TDM bus master circuit card during off–hours. The 
diagnostic procedure has a negative impact on call processing. See Modify the Display Voice Equipment Window Parameters
 on page 144
 for more...

3  
Voice System Administration  System Control
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 128
The system displays the Diagnose Equipment window (Figure 83 on page 128
).
Figure 83. Diagnose Equipment Window  
Table 10 on page 128
 describes the fields in this window.
Table 10. Field Descriptions for Diagnose Equipment Window
Field DescriptionEquipment to 
diagnose:
Specifies whether the type of equipment to be diagnosed is either a circuit 
card, channel, or...

3  
Voice System Administration  System Control
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 129
2  
Enter the information as described in Table 10 on page 128
.
3  
Press 
F3
 (Save). 
The system displays a report showing the status of the specified 
equipment.
4  
Press 
F6
 (Cancel) repeatedly until you return to the System Control 
menu.
Immediate 
diagnosis?:
Specifies whether or not there should be immediate diagnosis on the selected 
circuit card or bus....

3  
Voice System Administration  System Control
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 130
Voice Port Loop 
Around Test
The voice port loop around test allows you to initiate loop around test for a 
given channel. Use the following procedure to run the voice port loop around 
test:1  
Start at the System Control menu (Figure 82 on page 126
) and select
 
The system displays the Voice Port Loop Around Test window (Figure 83 on page 128
).
Figure 84. Voice...

3  
Voice System Administration  System Control
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 131
Table 11. Field Descriptions for Voice Port Loop Around Test Window
Field DescriptionDialing 
Channel
Enter the channel number to use to diagnose the target channel, or AUTO to 
have the system select a channel.
Target 
Channel
Enter the channel you want to diagnose.
Test Type
Enter the test type, press 
F2
 (Choices) to select a test type, or all to perform 
all...

3  
Voice System Administration  System Control
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 132
2  
Enter the information as described in Table 11 on page 131
.
3  
Press 
F3
 (Save). 
The system displays a report showing the status of the specified channel.
4  
Press 
F6
 (Cancel) repeatedly until you return to the System Control 
menu.
Immediate 
diagnosis?:
Specifies whether or not there should be immediate diagnosis on the selected 
channel. Type y for...

3  
Voice System Administration  System Control
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 133
Renumber Voice Channels
The Renumber Voice Channels option removes all nonexistent (NONEX) 
circuit cards from the voice equipment table, then reorders all existing 
equipment with E1/T1 circuit cards first, followed by Tip/Ring circuit cards, 
then SSP circuit cards. This reordering changes the channel numbers of 
some circuit cards. However, user–defined...

3  
Voice System Administration  System Control
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 134
The system displays the Renumber Voice Channels window (Figure 85 on page 134
).
Figure 85. Renumber Voice Channels Window  2  
Press 
F3
 (Renumber) to continue.
The system renumbers voice channels. 

3  
Voice System Administration  System Control
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 135
Report Voice System Status
Use the following procedure to see whether the voice system is running or 
stopped, and to view the current voice system run level. 1  
Start at the System Control menu (Figure 82 on page 126
) and select:
 
The system displays the Status of Voice System window (Figure 86 on page 135
).
Figure 86. Status of Voice System Window  2  
Press...

3  
Voice System Administration  System Control
Intuity™ CONVERSANT® System Version 7.0 Administration 
585-313-501 Issue 3 January 2000 136
Stop the Voice System
This procedure stops the voice system by taking all system channels out of 
service with the option to wait for in-progress calls to end.  Stopping the 
system is usually done when you are performing some type of routine service 
such as backup and restore.   When the system is stopped, the CPU does the 
following:•
Places the entire system in...