Lexmark X342n User Manual

Error messages troubleshooting
91
Error messages troubleshooting
ProblemSolution
Change MediaPress 1 to change the size and/or type of media, or press 2 to ignore the 
error message.
Note:To continue the job, press Start. To cancel the job, press Stop.
Close Front DoorClose the front cover until it locks.
Load ManualLoad print media into the manual feeder. For more information, see 
Loading paper in the manual feeder on page 32.
Load MediaLoad paper in the paper tray. For more information, see Loading...

Error messages troubleshooting
92
34 Short paperMake sure the correct media type and size have been selected for the 
existing print job. For more information, see Setting the paper type 
and size on page 35.
Press Start to resume printing
Note:Pressing Start may truncate the print job.
or
Press Stop to cancel the job.
Note:You cannot cancel an incoming fax.
37 Insufficient Collation 
Area
38 Memory FullThe MFP does not have enough memory to process the job.
Press Start to resume printing
or
Press...

Error messages troubleshooting
93
241.xx Paper JamSee 241/242 Paper Jam on page 81.
 
242.xx Paper Jam
251.xx Paper JamSee 251 Paper Jam on page 82.
290 Scanner Jam See 290/291/292 Scanner Jam on page 83.
291 Scanner Jam
292 Scanner Jam
9**.xx Service1Turn the power off for one minute.
2Turn the power on.
If the error message reappears, call a Lexmark service representative. 
For authorized service representatives in your area, visit 
www.lexmark.com.
ProblemSolution
Downloaded From ManualsPrinter.com...

Notices
94
Notices
Electronic emission notices
Federal Communications Commission (FCC) compliance information statement
Part 15
The Lexmark X340 (7003-100), X340n (7003-x050), and X342n (7003-110) have been tested and found to 
comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to 
the following two conditions: (1) this device may not cause harmful interference, and (2) this device must 
accept any interference received, including interference...

Notices
95
Notices
 
modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is 
also compliant. 
The Ringer Equivalence Number (REN) is used to determine the number of devices that may be connected to 
a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an 
incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the 
number of devices that may be...

Notices
96
Notices
 
European Community (EC) directives conformity
Declaration of Conformity with Regard to the EU Directive 1999/5/EC (R&TTE Directive) in languages of the 
European Community.
English Hereby, Lexmark International Inc., declares that this product is in compliance with the 
essential requirements and other relevant provisions of Directive 1999/5/EC.
Suomi Valmistaja Lexmark International Inc. vakuuttaa täten, että tämän tuotteen tyyppinen 
laite on direktiivin 1999/5/EY oleellisten...

Notices
97
Notices
 This product is in conformity with the protection requirements of EC Council directives 89/336/EEC, 73/23/
EEC, and 1999/5/EC on the approximation and harmonization of the laws of the Member States relating to 
electromagnetic compatibilityand safety of electrical equipment designed for use within certain voltage limits 
and on radio equipment andtelecommunications terminal equipment. The Official Declaration of Conformity 
may be viewed at www.lexmark.com/rtte.
Compliance is...

Notices
98
Notices
 
Korean MIC statement
If this symbol appears on your product, the accompanying statement is applicable.
Mercury statement
This product contains mercury in the lamp (

Notices
99
Notices
 
The equipment shall be set to ensure that automatic calls to different numbers are spaced such that there 
is not less than 5 seconds between the end of one call attempt and the beginning of another.
South Africa telecommunications notice
This modem must be used in conjunction with an approved surge protection device when connected to the 
PSTN.
Using this product in Germany
This product requires a German billing tone filter (Lexmark part number 14B5123) to be installed on any line...

Notices
100
Notices
 
Noise emission levels
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 
9296.
Printer energy consumption
The following table documents the power consumption characteristics of the printer.
The power consumption levels listed in the previous table represent time–averaged measurements. 
Instantaneous power draws may be substantially higher than the average.
Power Saver
This printer is designed with an energy–saving mode called Power...