Lexmark X 850 Owners Manual
Have a look at the manual Lexmark X 850 Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 166 Lexmark manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Repair information4-243 7500-XXX 2000-sheet dual input (TTM)–media feed unit assembly removal (tray 3) 1.Pull out the tray 3 assembly. 2.Pull out the tray 4 assembly. 3.Open the 2TM/TTM left door assembly. 4.Remove one screw securing the 2TM/TTM left door support strap (A). 5.Release the bosses on both sides securing the vertical turn guide (B). 6.Remove the vertical turn guide (B). 7.Release the bosses on both sides securing the upper vertical turn guide (C). 8.Remove the upper vertical turn guide (C). Front C Boss A BBoss BossBoss
4-244MFP Service Manual 7500-XXX 9.Release the harness from the clamp. 10.Disconnect the connector from the machine. Front Connector Clamps
Repair information4-245 7500-XXX 11.Remove three screws securing the media feed unit assembly (D). 12.Remove the media feed unit assembly (D) by pulling outward. 13.Remove two screws securing the rear bracket (E) to the media feed unit assembly (D). 14.Remove the rear bracket (E). Front Connector Clamps E Connector D
4-246MFP Service Manual 7500-XXX 2000-sheet dual input (TTM)–2TM/TTM media transport roll assembly removal 1.Open the left door assembly. 2.Remove two screws securing the bracket (A). 3.Disconnect the connector to the sensor (tray 3 feed-out) (B). 4.Remove the bracket (A). 5.Remove the large e-clip on the left securing the 2TM/TTM media transport roll assembly (C). 6.Slide the bushing (D) to the right. 7.Move the 2TM/TTM media transport roll assembly (C) leftward and outward in the direction of the arrow to remove. 8.Remove the 2TM/TTM media transport roll assembly (C). Note: One of the bushings may become detached. Note: When removing the 2TM/TTM media transport roll assembly (C), do not touch the rubber surface. Note: Before re-installing the 2TM/TTM media transport roll assembly (C), do not touch the rubber surface. D Projection Notch E-ringConnectorB A C E-ring D
Repair information4-247 7500-XXX 2000-sheet dual input (TTM)–sensor (tray 3 feed-out) removal 1.Open the left door assembly. 2.Remove two screws securing the bracket (A). 3.Disconnect the connector to the sensor (tray 3 feed-out) (B). 4.Remove the bracket (A). 5.Release the hooks securing the sensor (tray 3 feed-out) (B) to the bracket (A). 6.Remove the sensor (tray 3 feed-out) (B). AConnector Hook B Actuator
4-248MFP Service Manual 7500-XXX 2000-sheet dual input (TTM)–media feed lift motor removal 1.Remove the media feed unit assembly. See “2000-sheet dual input (TTM)–media feed unit assembly removal (tray 3)” on page 4-243 or “2000-sheet dual input (TTM)–media feed unit assembly removal (tray 4)” on page 4-239. 2.Disconnect the harness from the media feed lift motor (A). 3.Remove the two screws securing the media feed lift motor to the media feed unit assembly (B). 4.Remove the media feed lift motor (B). AB Connector Rear
Repair information4-249 7500-XXX 2000-sheet dual input (TTM)–lift coupling assembly removal 1.Remove the media feed unit assembly. See “2000-sheet dual input (TTM)–media feed unit assembly removal (tray 3)” on page 4-243 or “2000-sheet dual input (TTM)–media feed unit assembly removal (tray 4)” on page 4-239. 2.Remove the harness from bracket (A). 3.Remove three screws securing bracket (A) to the media feed unit assembly. 4.Remove bracket (A). Note: The gears may become detached from bracket (A). 5.Remove the e-ring with a prying tool securing the tray lift coupling (B) to bracket (A). 6.Remove the tray lift coupling gear 31 tooth (C). 7.Remove the spring (D). Note: Before re-installing, ensure all gears and washers attached to bracket (A) are securely installed. Clamp A RearE-ring Washer DCB
4-250MFP Service Manual 7500-XXX 2000-sheet dual input (TTM)–one-way clutch / gear assembly removal 1.Remove the media feed unit assembly. See “2000-sheet dual input (TTM)–media feed unit assembly removal (tray 3)” on page 4-243 or “2000-sheet dual input (TTM)–media feed unit assembly removal (tray 4)” on page 4-239. 2.Remove the harness from the bracket (A). 3.Remove the three screws securing the bracket (A) to the media feed unit assembly. 4.Remove the bracket (A). Note: The gears may become detached from the bracket (A). 5.Remove the tray lift one-way clutch (B). Harness Washer Clamp A RearB
Repair information4-251 7500-XXX 6.Remove the tray lift one-way gear 24 tooth (C). Note: Before re-installing, ensure all gears and washers are securely attached to the bracket (A). Harness A RearC Washer
4-252MFP Service Manual 7500-XXX 2000-sheet dual input (TTM)–media feed unit drive gear 13 tooth removal 1.Remove the media feed unit assembly. See “2000-sheet dual input (TTM)–media feed unit assembly removal (tray 3)” on page 4-243 or “2000-sheet dual input (TTM)–media feed unit assembly removal (tray 4)” on page 4-239. 2.Remove the harness from the bracket (A). 3.Remove the three screws securing the bracket (A) to the media feed unit assembly. 4.Remove the bracket (A). Note: Gears may become detached from the bracket (A). 5.Remove the tray lift one-way clutch. See “2000-sheet dual input (TTM)–feed roll one-way clutch removal” on page 4-260. 6.Remove the tray lift one-way gear 24 tooth. See “2000-sheet dual input (TTM)–one-way 22 tooth removal” on page 4-261. 7.Remove the media feed unit drive gear - 13 tooth (B). Note: Before re-installing, ensure all gears and washers are securely attached to the bracket (A). Harness Clamp A RearWasher Washer B