Lexmark X 850 Owners Manual
Have a look at the manual Lexmark X 850 Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 166 Lexmark manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Repair information4-73 7500-XXX Transfer roll assembly removal 1.Open the printer left door assembly. 2.Release the two plastic hooks on the transfer roll assembly (A). 3.Remove the transfer roll assembly (A) by lifting it upward. Note: When removing the transfer roll assembly (A), do not touch the roll surface. Note: Before reinstalling the transfer roll assembly (A), do not touch the roll surface. HookA LeftHook
4-74MFP Service Manual 7500-XXX Printer left door support strap removal 1.Remove the MPF rear cover. See “MPF rear cover removal” on page 4-58. 2.Open the printer left door assembly (A). 3.Remove the screw securing the printer left door support strap (B) to the printer left door (A). 4.Remove the e-clip securing the shaft (C) to the printer. 5.Remove the shaft (C). 6.Remove the printer left door support strap (B). A B C
Repair information4-75 7500-XXX Printer left door assembly removal Note: First, remove the duplex unit assembly if equipped. 1.Open the printer left door assembly. 2.Remove the screw securing the left door support strap (A) to the printer left door assembly (B). 3.Remove the printer left door assembly (B) by lowering it then lifting upward. A B Front
4-76MFP Service Manual 7500-XXX Switch (printer left door interlock) removal 1.Remove the rear motor cover. See “Rear motor cover removal” on page 4-11. 2.Open the printer left door assembly. 3.Remove the one screw securing the bracket (A) to the printer. 4.Remove the bracket (A). 5.Disconnect the connector from the switch (printer left door interlock) (B). 6.Release the hooks securing the switch (printer left door interlock) (B) to the bracket (A). 7.Remove the switch (printer left door interlock) (B). A RearB Connector
Repair information4-77 7500-XXX Transfer roll guide assembly removal 1.Open the printer left door assembly. 2.Remove the printer left door assembly. See “Printer left door assembly removal” on page 4-75. 3.Remove the transfer roll assembly. See “Transfer roll assembly removal” on page 4-73. 4.Release the two hooks securing the transfer roll guide assembly (A) to the printer left door assembly (B). 5.Remove the transfer roll guide assembly (A).
4-78MFP Service Manual 7500-XXX Printer left door assembly handle removal 1.Open the printer left door assembly. 2.Remove the printer left door assembly. See “Printer left door assembly removal” on page 4-75. 3.Remove the transfer roll guide assembly. See “Transfer roll guide assembly removal” on page 4-77. 4.Remove five screws securing the metal frame (A) to the plastic cover (B). 5.Remove the metal frame (A) by lifting it upward and sliding outward. 6.Remove the three screws securing the handle cover (C). 7.Remove the handle cover (C). 8.Remove the printer left door assembly handle (D). 9.Remove the spring (E). BE DA C
Repair information4-79 7500-XXX Registration roll assembly removal 1.Remove the MPF rear cover. See “MPF rear cover removal” on page 4-58. 2.Remove the MPF feed unit assembly. See “MPF feed unit assembly removal” on page 4-54. 3.Remove the printer left door assembly. See “Printer left door assembly removal” on page 4-75. 4.Remove the bosses on both ends of the vertical turn mylar guide (A). 5.Remove the vertical turn mylar guide (A). Warning: The vertical turn mylar guide (A) requires moderate force to remove. Be careful not to damage it. 6.Remove the two screws securing the registration mylar guide assembly (B) to the registration roll assembly (C). 7.Remove the registration mylar guide assembly (B). 8.Remove the two screws securing registration roll assembly (C). 9.Remove the registration roll assembly (C) by lifting it upward and outward in the direction of the arrow. Note: When removing the registration roll assembly (C), use care not to damage the two harnesses located on the backside of the assembly. 10.Release the harness from the clamp. 11.Disconnect the two connectors from the registration roll assembly (C). Note: •Before reinstalling the registration roll assembly (C), fit the bosses on the rear center of the assembly into the holes. •Before reinstalling the two harness connectors, ensure they are plugged in properly. B C Boss A BossFront Clamp Connector Connector C Left view
4-80MFP Service Manual 7500-XXX Registration clutch assembly removal 1.Remove the MPF rear cover. See “MPF rear cover removal” on page 4-58. 2.Remove the MPF feed unit assembly. See “MPF feed unit assembly removal” on page 4-54. 3.Remove the printer left door assembly. See “Printer left door assembly removal” on page 4-75. 4.Remove the registration roll assembly. See “Registration roll assembly removal” on page 4-79. 5.Remove the e-ring with a prying tool securing the registration clutch assembly (A) to the registration roll assembly (B). 6.Remove the registration clutch assembly (A) along with the harness. Note: •Before reinstalling, the harness for the clutch must be placed through the hole on the registration roll assembly (B). •Before reinstalling, the notch on the registration clutch assembly (A) must be placed over the boss of the registration roll assembly (B). A E-ring Boss Notch B
Repair information4-81 7500-XXX Sensor (registration) removal 1.Remove the MPF rear cover. See “MPF rear cover removal” on page 4-58. 2.Remove the MPF feed unit assembly. See “MPF feed unit assembly removal” on page 4-54. 3.Remove the printer left door assembly. See “Printer left door assembly removal” on page 4-75. 4.Remove the registration roll assembly. See “Registration roll assembly removal” on page 4-79. 5.Release the hooks securing the sensor (registration) (A) to the registration roll assembly (B). 6.Remove the sensor (registration) (A). 7.Disconnect the connector from the sensor (registration). Hook A B Front Hooks Front A
4-82MFP Service Manual 7500-XXX MPF/transport drive motor assembly removal 1.Remove the rear motor cover. See “Rear motor cover removal” on page 4-11. 2.Remove the rear lower cover. See “Rear lower cover removal” on page 4-12. 3.Open the printer left door assembly. 4.Remove the e-clip with needle nose pliers. Note: This e-clip is located inside the machine behind the printer left door. 5.Release the hook and disconnect the connector from the MPF/transport drive motor assembly (A). 6.Remove the three screws securing the MPF/transport drive motor assembly (A) to the machine. 7.Remove the MPF/transport drive motor assembly (A). A Connector Rear E-clip Front view