Lexmark W850dn User Manual

Menu itemDescription
Job Buffering
Off
On
AutoTemporarily stores jobs on the printer hard disk before printing. This menu appears
only if a formatted disk is installed.
Notes:
Off is the factory default setting.
The On value buffers jobs on the printer hard disk. This menu selection
appears only when a formatted disk is installed and is not defective.
The Auto setting buffers print jobs only if the printer is busy processing data
from another input port.
Changing this setting from the printer control...

Menu itemDescription
Print Setup Page
Print NetWare Setup
PagePrints a report containing information about the current network setup
Notes:
The Setup Page contains information about the network printer settings, such as the
TCP/IP address.
The NetWare Setup Page menu item appears only on models that support NetWare and
shows information about NetWare settings.
Network Card menu
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network  > Std Network Setup or Net...

Menu itemDescription
Activate
On
OffActivates TCP/IP
Note: On is the factory default setting.
View HostnameLets you view the current TCP/IP hostname
Note: This can be changed only from the Embedded Web Server.
IP AddressLets you view or change the current TCP/IP Address
Note: Manually setting the IP address sets the Enable DHCP and Enable Auto IP
settings to Off. It also sets Enable BOOTP and Enable RARP to Off on systems that
support BOOTP and RARP.
NetmaskLets you view or change the current TCP/IP...

Menu itemDescription
Enable IPv6
On
OffEnables IPv6 in the printer
Note: On is the factory default setting.
Auto Configuration
On
OffSpecifies whether the network adapter accepts the automatic IPv6
address configuration entries provided by a router
Note: On is the factory default setting.
View Hostname
View Address
View Router AddressLets you view the current setting
Note: These settings can be changed only from the Embedded Web
Server.
Enable DHCPv6
On
OffEnables DHCPv6 in the printer
Note: On is the...

AppleTalk menu
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network  > Std Network Setup or Net  Setup > AppleTalk
Menu itemDescription
Activate
Yes
NoActivates AppleTalk support
Note: Yes is the factory default setting.
View NameShows the assigned AppleTalk name
Note: The name can be changed only from the Embedded Web Server.
View AddressShows the assigned AppleTalk address
Note: The address can be changed only from the Embedded Web Server.
Set Zone
Provides a...

Menu itemDescription
NSQ/GSQ Mode
Yes
NoSpecifies the NSQ/GSQ Mode setting
Note: Yes is the factory default setting.
LexLink menu
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network  > Std Network Setup or Net  Setup > LexLink menu
Menu itemDescription
Activate
On
OffActivates LexLink support
Note: Off is the factory default setting.
View NicknameLets you view the assigned LexLink nickname
Note: The LexLink nickname can be changed only from the Embedded Web...

Menu itemDescription
NPA Mode
Auto
OffSets the printer to perform the special processing required for bidirectional
communication following the conventions defined by the NPA protocol
Notes:
Auto is the factory default setting.
Changing this setting from the printer control panel and then exiting the
menus causes the printer to restart. The menu selection is updated.
USB Buffer
Auto
Disabled
3K to Sets the size of the USB input buffer
Notes:
Auto is the factory default setting.
The Disabled setting turns...

Menu itemDescription
Primary SMTP Gateway
Primary SMTP Gateway Port
Secondary SMTP Gateway
Secondary SMTP Gateway PortSpecifies SMTP server port information
Note: 25 is the default SMTP gateway port. Range is 1‑65536.
SMTP Timeout
5–30Specifies the amount of time in seconds before the server stops trying to
send the e‑mail
Note: 30 seconds is the factory default setting.
Reply AddressSpecifies a reply address of up to 128 characters in e-mail sent by the
printer
Use SSL
Disabled
Negotiate
RequiredSets...

Security menu
Miscellaneous menu
Menu itemDescription
Login Restriction
Login failures
1-10 (3 attempts)
Failure time frame
1-60 (5 minutes)
Lockout time
1-60 (5 minutes)
Panel Login Timeout
1-900 (3 seconds)
Remote Login Timeout
1-120 (10 minutes)Limits the number and time frames of failed login attempts from the printer control
panel before all users are locked out
Notes:
“Login failures” specifies the number of failed login attempts before users are
locked out. 3 attempts is the factory default...

Disk Wiping menu
Menu itemDescription
Automatic Wiping
Single pass
Multiple passDisk Wiping erases only print job data that is not currently in use by the file system
from the printer hard disk. All permanent data on the printer hard disk is preserved,
such as downloaded fonts, macros, and held jobs.
Automatic Wiping marks all disk space used by a previous job and does not permit
the file system to reuse this space until it has been sanitized.
Only Automatic Wiping enables users to activate disk wiping...