Lexmark W850dn User Manual

10Press the up or down arrow button until  appears next to the job you want to print, and then press .
11Press the up or down arrow button until  appears next to the number of copies you want to print, and then press
.
Note: Use the keypad to enter a number if necessary.
For Macintosh users
1
With a document open, choose File > Print.
If necessary, click the disclosure triangle to see more options.
2From the print options or Copies & Pages pop‑up menu, choose Job Routing.
3Select your job type...

Printing from a flash drive
A USB port is located on the printer control panel. Insert a flash drive to print supported file types. Supported file types
include: .pdf, .gif, .jpeg, .jpg, .bmp, .png, .tiff, .tif, .pcx, .xps, and .dcx.
Lexmark has tested and approved the following USB flash memory devices:
Lexar FireFly 512 MB
Lexar FireFly 1 GB
SanDisk Cruizer Micro 512 MB
SanDisk Cruizer Micro 1 GB
Sony 512 MB
Sony 1 GB
Notes:
High‑speed flash drives must support the full‑speed USB standard. Flash drives...

3Press the up or down arrow button until  appears next to the document you want to print, and then press .
Note: Folders found on the flash drive appear as folders. File names are appended by the extension type (for
example, .jpg).
4Press  to print one copy, or enter the number of copies using the keypad, and then press  to initiate the
print job.
Note: Do not remove the flash drive from the printer until the document has finished printing.
If you leave the flash drive in the printer after leaving the...

Printing the print quality test pages
Print the print quality test pages to isolate print quality problems.
1Turn the printer off.
2Hold down  and the right arrow button while turning the printer on.
3Release the buttons when the clock appears, and wait for CONFIG MENU to appear.
4Press the up or down arrow button until Prt Quality Pgs appears, and then press .
The print quality test pages print.
5Press the up or down arrow button until Exit Config Menu appears, and then press .
Resetting the Printer...

3Select the print job you want to cancel.
4Click Delete.
For Macintosh users
1From the Apple menu, navigate to either of the following:
System Preferences > Print & Scan > select your printer > Open Print Queue
System Preferences > Print & Fax > select your printer > Open Print Queue
2From the printer window, select the print job you want to cancel, and then delete it.
Supported finishing features
12
3
1Standard bin
2Finisher Bin 1
3Finisher Bin 2
Standard bin
The paper capacity is 300 sheets.
Finishing...

Finisher Bin 1
The paper capacity is 500 sheets of A4/Letter and 300 sheets of A3/Ledger.
Envelopes, A5, A6, and Statement are not supported in this bin.
Finishing options are not supported in this bin.
Finisher Bin 2
The paper capacity is 3,000 sheets when the standard finisher is installed.
Finisher Bin 2 finishing features
SizeTwo‑hole punch*Three‑ or
Four‑hole punchOffsetSingle stapleDual staple
A3
A4
Note: Supported
only if feeding
orientation is long
edge.Note: Supported
only if feeding
orientation...

SizeTwo‑hole punch*Three‑ or
Four‑hole punchOffsetSingle stapleDual staple
Oficio
X
* For the Universal paper size, the finishing edge must be at least 9 in. (229 mm) for a 3‑hole punch and 10 in. (254 mm) for
a 4‑hole punch.
Punch—Two‑, three‑, or four‑hole punch settings
Single staple—One staple
Dual staple—Two staples
Adjusting toner darkness
1Type the printer IP address into the address field of your Web browser.
Note: If you do not know the IP address of the printer, then print a network setup page...

Understanding printer menus
Menus list
Paper Menu Reports Network/Ports
Default Source
Paper Size/Type
Configure MP
Substitute Size
Paper Texture
Paper Loading
Custom Types
Universal Setup
Bin SetupMenu Settings Page
Device Statistics
Network Setup Page
1
Profiles List
NetWare Setup Page
Print Fonts
Print Directory
2
Asset Report
Print DemoActive NIC
Standard Network
3
Standard USB
Parallel 
SMTP Setup
Security Settings Help
Miscellaneous Security Settings
Confidential Print
Disk Wiping
4
Security Audit...

Paper menu
Default Source menu
Menu itemDescription
Default Source
Tray 
MP Feeder
Manual Paper
Manual EnvSets a default paper source for all print jobs
Notes:
Tray 1 (standard tray) is the factory default setting.
Only an installed paper source will appear as a menu setting.
A paper source selected by a print job will override the Default Source
setting for the duration of the print job.
If the same size and type of paper are in two trays and the Paper Size and
Paper Type settings match, then the trays...

Menu itemDescription
Tray  Type
Plain Paper
Card Stock
Transparency
Recycled
Labels
Bond
Letterhead
Preprinted
Colored Paper
Light Paper
Heavy Paper
Rough/Cotton Paper
Custom Type Specifies the type of paper loaded in each tray
Notes:
Plain Paper is the factory default setting for Tray 1. Custom Type  is
the factory default setting for all other trays.
If available, a user‑defined name appears instead of Custom Type .
Use this menu item to configure automatic tray linking. If the same size
and type of...