Lexmark W820n User Manual

119
9Grasp both handles and firmly pull the fuser out.
10Dispose of the old fuser.
Installing a new fuser
1Remove the packaging from the new fuser.
2Pull the labels off of each side of the fuser.
3Use a flat blade screwdriver or a coin to turn each screw until they are loose.
Downloaded From ManualsPrinter.com Manuals 

120
4Pull the screws straight out, and then discard them.
5Grasp the right handle through its ring and pull it to the front. It slides up and locks into the
open position.
6Grasp the left handle through its ring and rotate it out toward you. It does not lock into position.
7Align the fuser with the opening in the printer, and then slide it into place.
Note:Push firmly on each side of the fuser near the handles until it is in place.
8Push both handles back to their original positions.
Downloaded From...

121
9Carefully tighten the green thumbscrews.
WARNING:Over tightening the screws can strip the threads.
10Close the printer front door (Door F).
11Close the printer side door (Door A).
12If the duplex unit is attached to the printer, close the duplex unit door (Door E).
13Reinstall the envelope feeder if it was removed. SeeReinstalling the envelope feeder.
14If you have already replaced all the items listed in the following note, you may turn the printer
on.
Note:Make sure you also follow the...

122
33
Replacing the transfer roller
The transfer roller is one of the items in the maintenance kit. Replace it when the printer displays the
80 Scheduled Maintenancemessage.
Removing the old transfer roller
1Turn the printer off.
2If the envelope feeder is attached to the printer, remove it. SeeRemoving the optional
envelope feeder.
3If the duplex unit is attached to the printer, open the duplex unit door (Door E).
aPush up on the latch to release the door.
bGently lower the door to the open position....

123
5Grasp the green tabs on each end of the transfer roller, and then pull forward to release them.
6Rotate the tabs toward the printer.
7While holding the tabs, pull straight up to remove the transfer roller.
8Dispose of the old transfer roller.
Downloaded From ManualsPrinter.com Manuals 

124
Installing the new transfer roller
1Remove the packaging from the new transfer roller.
2Hold the transfer roller, and rotate the tabs in the direction as shown.
Note:To help in the orientation of the transfer roller, notice that the tabs are not the same
shape or size.
3Align the steel bars on the transfer roller with the grooves in the printer.
4Push firmly on each end of the transfer roller until the barssnapinto the grooves.
5Grasp the tabs and rotate them as shown.
Steel bar
Groove
Downloaded...

125
6Push down on the tabs until theysnapinto place.
7Close the printer side door (Door A).
8Close the duplex unit door (Door E).
9Reinstall the envelope feeder, if necessary. SeeReinstalling the envelope feeder.
10If you have already replaced all the items listed in the following note, you may turn the printer
on.
Note:Make sure you also follow the instructions inReplacing the fuser,Replacing pick
rollers,Cleaning the wiper blade, andResetting the maintenance page
counter.
Downloaded From...

126
34
Replacing pick rollers
The pick rollers come in a package of 15 in the maintenance kit. Replace three in each tray when the
printer issues the80 Scheduled Maintenancemessage. If you don’t have a high capacity feeder,
you will have nine pick rollers left over from the package.
A pick roller transports the paper from an input tray to the paper path.
Removing old pick rollers
1Remove trays 1 and 2 from the printer, and trays 3 and 4 from the optional high capacity input
feeder if it is installed. See...

127
6Push the tab away from the metal bar.
7Pull the pick roller straight out.
8Locate the spring-loaded metal plate in front of the two top pick rollers.
9Pull the metal plate down and to the right. Hold it in place.
10Remove the other two pick rollers. Top pick rollers rotate either way to locate the tab.
aPush the tab away from the metal bar.
Downloaded From ManualsPrinter.com Manuals 

128
bPull the pick roller straight out.
11Dispose of the pick rollers.
CAUTION:To prevent a falling hazard, dispose of the pick rollers immediately and in a proper
manner.
12Completestep 5 on page 126tostep 11 on page 128fortray2,andtray3ifyouhavethe
optional high capacity feeder installed.
13For tray 4, open Door C for better access. Then, completestep 5 on page 126tostep 11 on
page 128.
14For tray 5, pull the metal plate in front of the pick rollers forward.
15Remove the three pick rollers in tray 5 as...