Lexmark E462DTN User Manual

							Menu itemDescription
Recycled
Paper
Card Stock
Transparency
Labels
Envelope
CottonSpecifies a paper type when the Recycled setting is selected in other menus
Notes:
Paper is the factory default setting.
The Recycled type must be supported by the selected tray or feeder in
order for you to print from that source.
Universal Setup menu
These menu items are used to specify the height, width, and feed direction of the Universal Paper Size. The Universal
Paper Size is a user‑defined paper size. It is listed with the other paper size settings and includes similar options, such
as support for duplex printing and printing multiple pages on one sheet.
Menu itemDescription
Units of Measure
Inches
MillimetersIdentifies the units of measure
Notes:
Inches is the US factory default setting.
Millimeters is the international factory default setting.
Portrait Width
3–14.17 inches
76–360 mmSets the portrait width
Notes:
If the width exceeds the maximum, then the printer uses the
maximum width allowed.
8.5 inches is the US factory default setting. Inches can be increased
in 0.01‑inch increments.
216 mm is the international factory default setting. Millimeters can
be increased in 1‑mm increments.
Portrait Height
3–14.17 inches
76–360 mmSets the portrait height
Notes:
If the height exceeds the maximum, then the printer uses the
maximum height allowed.
14 inches is the US factory default setting. Inches can be increased in
0.01‑inch increments.
356 mm is the international factory default setting. Millimeters can
be increased in 1‑mm increments.
Feed Direction
Short Edge
Long EdgeSpecifies the feed direction
Notes:
Short Edge is the factory default setting.
Long Edge appears only if the longest edge is shorter than the
maximum length supported in the tray.
Understanding printer menus81
Downloaded From ManualsPrinter.com Manuals 
						

							Reports menu
Reports menu
To print a report, use the arrow buttons to navigate to the type of report you want, and then press .
Menu itemDescription
Menu Settings PagePrints a report containing information about paper loaded into trays, installed
memory, the total page count, alarms, timeouts, the printer control panel
language, the TCP/IP address, the status of supplies, the status of the network
connection, and other information
Device StatisticsPrints a report containing printer statistics such as supply information and details
about printed pages
Network Setup PagePrints a report containing information about the network printer settings, such
as the TCP/IP address information
Note: This menu item appears only for network printers or printers connected
to print servers.
Network  Setup PagePrints a report containing information about the network printer settings, such
as the TCP/IP address information
Notes:
This menu item is available when more than one network option is
installed.
This menu item appears only for network printers or printers connected to
print servers.
Wireless Setup PagePrints a report containing information about the wireless network printer
settings, such as the TCP/IP address information
Notes:
This menu item is available on the wireless printer model.
This menu item appears only for network printers or printers connected to
print servers.
Profiles ListPrints a list of profiles stored in the printer
NetWare Setup PagePrints a report containing NetWare‑specific information about the network
settings
Note: This menu item appears only for printers with an internal print server
installed.
Print Fonts
PCL Fonts
PostScript FontsPrints a report in English of all the fonts available for the printer language currently
set in the printer
Note: A separate list is available for PCL and PostScript emulations. Each
emulation report contains print samples and information about the available
fonts for each language.
Understanding printer menus82
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
Print DirectoryPrints a list of all the resources stored on an optional flash memory card
Notes:
Job Buffer Size must be set to 100%.
The optional flash memory must be installed correctly and working
properly.
Asset ReportPrints a report containing asset information including the printer serial number
and model name. The report contains text and UPC barcodes that can be scanned
into an asset database.
Network/Ports menu
Active NIC menu
Menu itemDescription
Active NIC
Auto
Notes:
Auto is the factory default setting.
This menu item appears only if an optional network card is installed.
Standard Network or Network  menus
Menu itemDescription
PCL SmartSwitch
On
OffSets the printer to automatically switch to PCL emulation when a print job requires
it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PostScript emulation if PS
SmartSwitch is set to On. It uses the default printer language specified in the
Setup menu if PS SmartSwitch is set to Off.
PS SmartSwitch
On
OffSets the printer to automatically switch to PS emulation when a print job requires
it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PCL emulation if PCL
SmartSwitch is set to On. It uses the default printer language specified in the
Setup menu if PCL SmartSwitch is set to Off.
Understanding printer menus83
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
NPA Mode
Off
AutoSets the printer to perform the special processing required for bidirectional
communication following the conventions defined by the NPA protocol
Notes:
Auto is the factory default setting.
Changing this setting from the printer control panel and then exiting the
menus causes the printer to restart. The menu selection is updated.
Network Buffer
Auto
3K to Sets the size of the network input buffer
Notes:
Auto is the factory default setting.
The value can be changed in 1K increments.
The maximum size allowed depends on the amount of memory in the printer,
the size of the other link buffers, and whether Resource Save is set to On or
Off.
To increase the maximum size range for the Network Buffer, disable or
reduce the size of the parallel and USB buffers.
Changing this setting from the printer control panel and then exiting the
menus causes the printer to restart. The menu selection is updated.
Mac Binary PS
On
Off
AutoSets the printer to process Macintosh binary PostScript print jobs
Notes:
Auto is the factory default setting.
The Off setting filters print jobs using the standard protocol.
The On setting processes raw binary PostScript print jobs.
Std Network Setup
Reports
Network Card
TCP/IP
IPv6
Wireless
AppleTalk
NetWare
LexLink
Net  Setup
Reports
Network Card
TCP/IP
IPv6
Wireless
Apple Talk
NetWare
LexLinkFor descriptions and settings of the network setup menus, see the following:
“Reports menu (under the Network/Ports menu)” on page 85
“Network Card menu” on page 85
“TCP/IP menu” on page 85
“IPv6 menu” on page 86
“Wireless menu” on page 87
“AppleTalk menu” on page 88
“NetWare menu” on page 88
“LexLink menu” on page 89
Note: The Wireless menu appears only when the printer is connected to a
wireless network.
Understanding printer menus84
Downloaded From ManualsPrinter.com Manuals 
						

							Reports menu (under the Network/Ports menu)
The Reports menu item is available from the Network/Ports menu:
Network/Ports > Standard Network or Network  > Std Network Setup or Net  Setup > Reports
Menu itemDescription
Print Setup Page
Print NetWare Setup
PagePrints a report containing information about the current network setup
Notes:
The Setup Page contains information about the network printer settings, such as the
TCP/IP address.
The NetWare Setup Page menu item appears only on models that support NetWare and
shows information about NetWare settings.
Network Card menu
This menu is available from the Network/Ports menu:
Network/Ports > Network Menu > Network Setup > Network Card
Menu itemDescription
View Card Status
Connected
DisconnectedLets you determine whether the Network Card is connected
View Card SpeedReflects the speed of a currently active network card
Network Address
UAA
LAALets you view the network addresses
Job Timeout
0‑225 secondsSets the amount of time in seconds that a network print job can take before it
is canceled
Notes:
90 seconds is the factory default setting.
A setting value of 0 disables the timeout.
If a value of 1–9 is selected, the setting is saved as 10.
Banner Page
On
OffAllows the printer to print a banner page
Note: Off is the factory default setting.
TCP/IP menu
Note: This menu is available only for network models or printers attached to print servers.
This menu is available from the Network/Ports menu: Understanding printer menus85
Downloaded From ManualsPrinter.com Manuals 
						

							Network/Ports > Network Menu > Network Setup > TCP/IP
Menu itemDescription
Activate
On
OffActivates TCP/IP
Note: On is the factory default setting.
View HostnameLets you view the current TCP/IP hostname
Note: This can be changed only from the Embedded Web Server.
IP AddressLets you view or change the current TCP/IP Address information
Note: Manually setting the IP address sets the Enable DHCP and Enable Auto IP
settings to Off. It also sets Enable BOOTP and Enable RARP to Off on systems that
support BOOTP and RARP.
NetmaskLets you view or change the current TCP/IP Netmask information
GatewayLets you view or change the current TCP/IP Gateway information
Enable DHCP
On
OffSpecifies the DHCP address and parameter assignment setting
Note: On is the factory default setting.
Enable RARP
On
OffSpecifies the RARP address assignment setting
Note: On is the factory default setting.
Enable BOOTP
On
OffSpecifies the BOOTP address assignment setting
Note: On is the factory default setting.
Enable Auto IP
Yes
NoSpecifies the Zero Configuration Networking setting
Note: Yes is the factory default setting.
Enable FTP/TFTP
Yes
NoEnables the built-in FTP server, which allows files to be transferred to the printer
Note: Yes is the factory default setting.
Enable HTTP Server
Yes
NoEnables the built-in Web server (Embedded Web Server). When enabled, the printer
can be monitored and managed remotely using a Web browser.
Note: Yes is the factory default setting.
WINS Server AddressLets you view or change the current WINS Server Address
DNS Server AddressLets you view or change the current DNS Server Address
Enable HTTPS
Yes
NoLets you view or change the current HTTPS setting
Note: Yes is the factory default setting.
IPv6 menu
Use the following menu items to view or set the Internet Protocol version 6 (IPv6) information.
Note: This menu is available only for network models or printers attached to print servers. Understanding printer menus86
Downloaded From ManualsPrinter.com Manuals 
						

							This menu is available from the Network/Ports menu:
Network/Ports > Network Menu  > Network Setup  > IPv6
Menu itemDescription
Enable IPv6
On
OffEnables IPv6 in the printer
Note: On is the factory default setting.
Auto Configuration
On
OffSpecifies whether the network adapter accepts the automatic IPv6
address configuration entries provided by a router
Note: On is the factory default setting.
View Hostname
View Address
View Router AddressLets you view the current setting
Note: These settings can be changed only from the Embedded Web
Server.
Enable DHCPv6
On
OffEnables DHCPv6 in the printer
Note: On is the factory default setting.
Wireless menu
Use the following menu items to view or configure the wireless internal print server settings.
Note: This menu is available only for models connected to a wireless network.
This menu is available from the Network/Ports menu:
Network/Ports > Network  > Net  Setup > Wireless
Menu itemDescription
Network Mode
Infrastructure
Ad hocSpecifies the network mode
Notes:
Infrastructure mode lets the printer access a network using an
access point.
Ad hoc is the factory default setting. Ad hoc mode configures the
printer for wireless networking directly between it and a computer.
Compatibility
802.11n
802.11b/g
802.11b/g/nSpecifies the wireless standard for the wireless network
Choose Network
Lets you select an available network for the printer to use
View Signal QualityLets you view the quality of the wireless connection
View Security ModeLets you view the encryption method for the wireless connection.
“Disabled” indicates that the wireless network is not encrypted.
Understanding printer menus87
Downloaded From ManualsPrinter.com Manuals 
						

							AppleTalk menu
This menu is available from the Network/Ports menu:
Network/Ports > Network Menu  > Network Setup  > AppleTalk
Menu itemDescription
Activate
On
OffActivates or deactivates AppleTalk support
Note: On is the factory default setting.
View NameShows the assigned AppleTalk name
Note: The name can be changed only from the Embedded Web Server.
View AddressShows the assigned AppleTalk address
Note: The address can be changed only from the Embedded Web Server.
Set Zone
Provides a list of AppleTalk zones available on the network
Note: The default setting is the default zone for the network. If no default
zone exists, the zone marked with an * is the default setting.
NetWare menu
This menu is available from the Network/Ports menu:
Network/Ports > Network Menu > Network Setup > NetWare
Menu itemDescription
Activate
Yes
NoActivates or deactivates NetWare support
Note: No is the factory default setting.
View Login NameShows the assigned NetWare login name
Note: This can be changed only from the Embedded Web Server.
Print ModeShows the assigned NetWare print mode
Note: This can be changed only from the Embedded Web Server.
Network NumberShows the assigned NetWare network number
Note: This can be changed only from the Embedded Web Server.
Select SAP Frames
Ethernet 802.2
Ethernet 802.3
Ethernet Type II
Ethernet SNAPEnables the Ethernet frame type setting
Notes:
On is the factory default setting for all menu items.
Values for each of the Ethernet frame types are On and Off.
Packet Burst
Yes
NoReduces network traffic by allowing the transfer and acknowledgement of
multiple data packets to and from the NetWare server
Note: Yes is the factory default setting.
Understanding printer menus88
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
NSQ/GSQ Mode
Yes
NoSpecifies the NSQ/GSQ Mode setting
Note: Yes is the factory default setting.
LexLink menu
This menu is available from the Network/Ports menu:
Network/Ports > Network Menu > Network Setup > LexLink menu
Menu itemDescription
Activate
On
OffActivates or deactivates LexLink support
Note: Off is the factory default setting.
View NicknameShows the assigned LexLink nickname
Note: The LexLink nickname can be changed only from the Embedded Web
Server.
USB menu
Menu itemDescription
PCL SmartSwitch
On
OffSets the printer to automatically switch to PCL emulation when a print job received
through a USB port requires it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PostScript emulation if the PS
Smartswitch setting is On. It uses the default printer language specified in the
Setup menu if the PS SmartSwitch setting is Off.
PS SmartSwitch
On
OffSets the printer to automatically switch to PS emulation when a print job received
through a USB port requires it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PCL emulation if the PCL
Smartswitch setting is On. It uses the default printer language specified in the
Setup menu if the PCL SmartSwitch setting is Off.
NPA Mode
On
Off
AutoSets the printer to perform the special processing required for bidirectional
communication following the conventions defined by the NPA protocol
Notes:
Auto is the factory default setting.
Changing this setting causes the printer to restart.
Understanding printer menus89
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
USB Buffer
Disabled
Auto
3K to Sets the size of the USB input buffer
Notes:
Auto is the factory default setting.
The Disabled setting turns off job buffering. Any jobs already buffered on the
disk are printed before normal processing is resumed.
The USB buffer size value can be changed in 1K increments.
The maximum size allowed depends on the amount of memory in the printer,
the size of the other link buffers, and whether the Resource Save setting is On
or Off.
To increase the maximum size range for the USB Buffer, disable or reduce the
size of the parallel and network buffers.
Changing this setting causes the printer to restart.
Mac Binary PS
On
Off
AutoSets the printer to process Macintosh binary PostScript print jobs
Notes:
Auto is the factory default setting.
The Off setting filters print jobs using the standard protocol.
The On setting processes raw binary PostScript print jobs.
ENA Address
...Sets the network address information for an external print server that is attached to
the printer using a USB cable
Note: This menu item is available only if the printer is attached to an external print
server through the USB port.
ENA Netmask
...Sets the netmask information for an external print server that is attached to the printer
using a USB cable
Note: This menu item is available only if the printer is attached to an external print
server through the USB port.
ENA Gateway
...Sets the gateway information for an external print server that is attached to the printer
using a USB cable
Note: This menu item is available only if the printer is attached to an external print
server through the USB port.
Understanding printer menus90
Downloaded From ManualsPrinter.com Manuals