Lexmark C935dn User Manual
Have a look at the manual Lexmark C935dn User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 166 Lexmark manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Configured models 1Standard exit bin 2Control panel 3Standard 520‑sheet tray (Tray 1) 4–6The High capacity feeder holds 2520 sheets and includes: •4—520‑sheet tray (Tray 2) 5—867‑sheet tray (Tray 3) 6—1133‑sheet tray (Tray 4) 7Multipurpose feeder 8Duplex unit 1Standard exit bin 2Control panel Learning about the printer11 Downloaded From ManualsPrinter.com Manuals
3Standard 520‑sheet tray (Tray 1) 4‑6The Tandem tray module (TTM) holds 1560 sheets and includes: 4—520‑sheet tray (Tray 2) 5—520‑sheet tray (Tray 3) 6—520‑sheet tray (Tray 4) 7Multipurpose feeder 8Duplex unit Fully configured model 1Horizontal transport unit (HTU) 2Control panel 3Finisher 4Finisher standard bin 5Finisher bin 1 6Finisher bin 2 (booklet‑maker) 7Standard 520‑sheet tray (Tray 1) 8–10The High capacity feeder includes: 8—520‑sheet tray (Tray 2) 9—867‑sheet tray (Tray 3) 10—1133‑sheet tray (Tray 4) 11Multipurpose feeder Learning about the printer12 Downloaded From ManualsPrinter.com Manuals
12Duplex unit Note: The finisher shown above is the booklet finisher. The standard finisher is not shown. Understanding the control panel Control panel itemDescription 1Display Shows messages and pictures that communicate the status of the printer 2Indicator light Indicates the printer status: Off—The power is off. Blinking green—The printer is warming up, processing data, or printing. Solid green—The printer is on, but idle. Solid red—Operator intervention is needed. 3Keypad Enter numbers or symbols on the display. 4Navigation buttons Press or to scroll through menu lists. Press or to scroll through values or text that roll to another screen. 5Select Press to initiate action on a menu item. 6Stop Stops all printer activity A list of options is offered once Stopped appears on the display. 7Menu Opens the menu index Note: The menus are available only when the printer is in the Ready state. Learning about the printer13 Downloaded From ManualsPrinter.com Manuals
Control panel itemDescription 8USB Direct interface Use this port to connect a USB flash memory device to the printer. You can print from the connected device. 9Back Returns the display to the previous screen Learning about the printer14 Downloaded From ManualsPrinter.com Manuals
Installing options Installing internal options CAUTION—SHOCK HAZARD: If you are installing memory or option cards sometime after setting up the printer, turn the printer off and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, turn them off as well and unplug any cables going to the printer. You can customize your printer connectivity and memory capacity by adding optional cards. The instructions in this section explain how to install the available cards; you can also use them to locate a card for removal. Available options Memory cards Printer memory Flash memory Fonts Firmware cards Bar Code and Forms IPDS and SCS/TNe PrintCryptionTM PRESCRIBE Other internal options Printer hard disk RS‑232 serial interface card Parallel 1284‑B interface card MarkNetTM N8000 Series Internal Print Servers Installing options15 Downloaded From ManualsPrinter.com Manuals
Accessing the system board to install internal options CAUTION—SHOCK HAZARD: Turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, turn them off as well and unplug any cables going into the printer. Note: This operation requires a #2 Phillips screwdriver. 1Remove the cover and system board. aTurn the screws on the cover counterclockwise, and then remove them. bGently pull the cover and system board away from the printer, and then remove it. 2Use the illustration below to locate the appropriate connector. Warning—Potential Damage: System board electrical components are easily damaged by static electricity. Touch something metal on the printer before touching any system board electronic components or connectors. Installing options16 Downloaded From ManualsPrinter.com Manuals
1Firmware and flash memory card connectors 2Memory card connector 3Internal print server connector 4Hard disk connector Installing a memory card CAUTION—SHOCK HAZARD: If you are installing a memory card after setting up the printer, turn the printer off, and unplug the power cord from the wall outlet before continuing. Warning—Potential Damage: System board electrical components are easily damaged by static electricity. Touch something metal on the printer before touching any system board electronic components or connectors. An optional memory card can be purchased separately and attached to the system board. To install the memory card: 1Access the system board. 2Unpack the memory card. Note: Avoid touching the connection points along the edge of the card. 3Open the memory card connector latches. Installing options17 Downloaded From ManualsPrinter.com Manuals
4Align the notches on the memory card with the ridges on the connector. 1Notches 2Ridges 5Push the memory card straight into the connector until it snaps into place. 6Reinstall the system board. Installing a flash memory or firmware card The system board has two connections for an optional flash memory or firmware card. Only one of each may be installed, but the connectors are interchangeable. CAUTION—SHOCK HAZARD: If installing a flash memory or firmware card after setting up the printer, turn the printer off, and unplug the power cord from the wall outlet before continuing. Warning—Potential Damage: System board electrical components are easily damaged by static electricity. Touch something metal on the printer before touching any system board electronic components or connectors. 1Access the system board. 2Unpack the card. Note: Avoid touching the connection points along the edge of the card. Installing options18 Downloaded From ManualsPrinter.com Manuals
3Holding the card by its sides, align the plastic pins on the card with the holes on the system board. 1Plastic pins 2Metal pins 4Push the card firmly into place. Notes: The entire length of the connector on the card must touch and be flush against the system board. Be careful not to damage the connectors. 5Reinstall the system board. Installing options19 Downloaded From ManualsPrinter.com Manuals
Installing a printer hard disk CAUTION—SHOCK HAZARD: If installing a printer hard disk after setting up the printer, turn the printer off, and unplug the power cord from the wall outlet before continuing. Warning—Potential Damage: System board electrical components and hard disks are easily damaged by static electricity. Touch something metal on the printer before touching any system board electronic components, connectors, or the hard disk. Note: A #2 Phillips screwdriver is needed to attach the hard disk to the mounting plate. 1Access the system board. 2Remove the mounting plate, hard disk, ribbon cable, and attachment screws from the package. 3Attach the ribbon cable to the hard disk. 4Attach the mounting plate to the hard disk with the screws. Installing options20 Downloaded From ManualsPrinter.com Manuals