Lexmark C935dn User Manual

							Menu itemDescription
Scale
1–400%Scales the default font for HTML documents
Notes:
100% is the factory default setting.
Scaling can be increased in 1% increments.
Orientation
Portrait
LandscapeSets the page orientation for HTML documents
Note: Portrait is the factory default setting.
Margin Size
8–255 mmSets the page margin for HTML documents
Notes:
19 mm is the factory default setting.
Margin size can be increased in 1‑mm increments.
Backgrounds
Do Not Print
PrintSpecifies whether to print backgrounds on HTML documents
Note: Print is the factory default setting.
Image menu
Menu itemDescription
Auto Fit
On
OffSelects the optimal paper size, scaling, and orientation
Notes:
On is the factory default setting.
The On setting overrides scaling and orientation settings for some images.
Invert
On
OffInverts bi‑tonal monochrome images
Notes:
Off is the factory default setting.
The font size can be increased in 1‑point increments.
This setting does not apply to GIF or JPEG images.
Scaling
Anchor Top Left
Best Fit
Anchor Center
Fit Height/Width
Fit Height
Fit WidthScales the image to fit the selected paper size
Notes:
Best Fit is the factory default setting.
When Auto Fit is set to On, Scaling is automatically set to Best Fit.
Orientation
Portrait
Landscape
Rev Portrait
Rev LandscapeSets the image orientation
Note: Portrait is the factory default setting.
Understanding printer menus101
Downloaded From ManualsPrinter.com Manuals 
						

							Security menu
Menu itemDescription
Max Invalid PIN
Off
2–10Limits the number of times an invalid PIN can be entered
Notes:
Off is the factory default setting.
This menu item appears only if a printer hard disk is installed.
Once the limit is reached, the confidential print jobs for that user name are
deleted.
Job Expiration
Off
1 hour
4 hours
24 hours
1 weekLimits the amount of time a confidential job stays in the printer before it is deleted
Note: Off is the factory default setting.
Network/Ports menu
TCP/IP menu
Use the following menu items to view or set the TCP/IP information.
Note: This menu is available only for network models or printers attached to print servers.
Menu itemDescription
TCP/IP
View HostnameShows the current TCP/IP hostname
TCP/IP
Address
Netmask
GatewayLets you view or change the current TCP/IP address information
Note: This is a four‑field IP address.
Understanding printer menus102
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
TCP/IP
Enable DHCP
On
Off
Enable RARP
On
Off
Enable BOOTP
On
Off
AutoIP
On
Off
Enable FTP/TFTP
On
Off
HTTP Server Enabled
On
OffLets you view or change the setting
Note: On is the factory default setting.
TCP/IP
WINS Server Address
DNS Server AddressLets you view or change the setting
Note: This is a four‑field IP address.
IPv6 menu
Use the following menu items to view or set the Internet Protocol version 6 (IPv6) information.
Note: This menu is available only for network models or printers attached to print servers.
Menu itemDescription
IPv6
Enable IPv6
Yes
NoEnables IPv6 in the printer
Note: Yes is the factory default setting.
IPv6
Auto Configuration
On
OffEnables the network adapter to accept the automatic IPv6 address
configuration entries provided by a router
Note: On is the factory default setting.
IPv6
View Hostname
View Address
View Router AddressShows the setting
Understanding printer menus103
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
IPv6
Enable DHCPv6
Off
OnEnables DHCPv6 in the printer
Note: Off is the factory default setting.
Wireless menu
Use the following menu items to view or configure the wireless internal print server settings.
Note: This menu is available only for network models or printers attached to print servers when an optional wireless
internal print server is installed in the printer.
Menu itemDescription
Mode
Infrastructure
Ad hocLets you select a mode
Notes:
Infrastructure mode makes the printer wireless network accessible
through an access point.
Ad hoc mode configures the printer for peer‑to‑peer wireless
networking.
Network Name
Lets you select an available network for the printer to use
Standard Network and Network  menus
Menu itemDescription
PCL SmartSwitch
On
OffSets the printer to automatically switch to PCL emulation when a print job requires
it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PostScript emulation if PS
SmartSwitch is set to On. It uses the default printer language specified in the
Setup menu if PS SmartSwitch is set to Off.
PS SmartSwitch
On
OffSets the printer to automatically switch to PS emulation when a print job requires
it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PCL emulation if PCL
SmartSwitch is set to On. It uses the default printer language specified in the
Setup menu if PCL SmartSwitch is set to Off.
Understanding printer menus104
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
NPA Mode
Off
AutoSets the printer to perform the special processing required for bidirectional
communication following the conventions defined by the NPA protocol
Notes:
Auto is the factory default setting.
Changing this setting from the control panel and then exiting the menus
causes the printer to restart. The menu selection is updated.
Network Buffer
Auto
3k to Sets the size of the network input buffer
Notes:
Auto is the factory default setting.
The value can be changed in 1k increments.
The maximum size allowed depends on the amount of memory in the printer,
the size of the other link buffers, and whether Resource Save is set to On or
Off.
To increase the maximum size range for the Network Buffer, disable or
reduce the size of the parallel, serial, and USB buffers.
Changing this setting from the control panel and then exiting the menus
causes the printer to restart. The menu selection is updated.
Job Buffering
On
Off
AutoTemporarily stores jobs on the printer hard disk before printing
Notes:
Off is the factory default setting.
The On value buffers jobs on the printer hard disk. This menu selection
appears only when a formatted disk is installed and is not defective.
The Auto setting buffers print jobs only if the printer is busy processing data
from another input port.
Changing this setting from the control panel and then exiting the menus
causes the printer to restart. The menu selection is updated.
Mac Binary PS
On
Off
AutoSets the printer to process Macintosh binary PostScript print jobs
Notes:
Auto is the factory default setting.
The Off setting filters print jobs using the standard protocol.
The On setting processes raw binary PostScript print jobs.
Understanding printer menus105
Downloaded From ManualsPrinter.com Manuals 
						

							Standard USB and USB  menus
Menu itemDescription
PCL SmartSwitch
On
OffSets the printer to automatically switch to PCL emulation when a print job received
through a USB port requires it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PostScript emulation if the PS
Smartswitch setting is On. It uses the default printer language specified in the
Setup menu if the PS SmartSwitch setting is Off.
PS SmartSwitch
On
OffSets the printer to automatically switch to PS emulation when a print job received
through a USB port requires it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PCL emulation if the PCL
Smartswitch setting is On. It uses the default printer language specified in the
Setup menu if the PCL SmartSwitch setting is Off.
NPA Mode
On
Off
AutoSets the printer to perform the special processing required for bidirectional
communication following the conventions defined by the NPA protocol
Notes:
Auto is the factory default setting.
Changing this setting from the control panel and then exiting the menus causes
the printer to restart. The menu selection is updated.
USB Buffer
Disabled
Auto
3k to Sets the size of the USB input buffer
Notes:
Auto is the factory default setting.
The Disabled setting turns off job buffering. Any jobs already buffered on the
disk are printed before normal processing is resumed.
The USB buffer size value can be changed in 1k increments.
The maximum size allowed depends on the amount of memory in the printer,
the size of the other link buffers, and whether the Resource Save setting is On
or Off.
To increase the maximum size range for the USB Buffer, disable or reduce the
size of the parallel, serial, and network buffers.
Changing this setting from the control panel and then exiting the menus causes
the printer to restart. The menu selection is updated.
Understanding printer menus106
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
Job Buffering
On
Off
AutoTemporarily stores jobs on the printer hard disk before printing
Notes:
Off is the factory default setting.
The On setting buffers jobs on the printer hard disk.
The Auto setting buffers print jobs only if the printer is busy processing data
from another input port.
Changing this setting from the control panel and then exiting the menus causes
the printer to restart. The menu selection is updated.
Mac Binary PS
On
Off
AutoSets the printer to process Macintosh binary PostScript print jobs
Notes:
Auto is the factory default setting.
The Off setting filters print jobs using the standard protocol.
The On setting processes raw binary PostScript print jobs.
ENA Address
Sets the network address information for an external print server that is attached to
the printer using a USB cable
Note: This menu item is available only if the printer is attached to an external print
server through the USB port.
ENA Netmask
Sets the netmask information for an external print server that is attached to the
printer using a USB cable
Note: This menu item is available only if the printer is attached to an external print
server through the USB port.
ENA Gateway
Sets the gateway information for an external print server that is attached to the printer
using a USB cable
Note: This menu item is available only if the printer is attached to an external print
server through the USB port.
Serial  menu
Menu itemDescription
PCL SmartSwitch
On
OffSets the printer to automatically switch to PCL emulation when a print job received
through a serial port requires it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PostScript emulation if PS
SmartSwitch is set to On. It uses the default printer language specified in the
Setup menu if PS SmartSwitch is set to Off.
Understanding printer menus107
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
PS SmartSwitch
On
OffSets the printer to automatically switch to PS emulation when a print job received
through a serial port requires it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PCL emulation if PCL
SmartSwitch is set to On. It uses the default printer language specified in the
Setup menu if PCL SmartSwitch is set to Off.
NPA Mode
On
Off
AutoSets the printer to perform the special processing required for bidirectional
communication following the conventions defined by the NPA protocol
Notes:
Auto is the factory default setting.
When the On setting is used, the printer performs NPA processing. If the data
is not in NPA format, it is rejected as bad data.
When the Off setting is used, the printer does not perform NPA processing.
When the Auto setting is used, the printer examines data, determines the
format, and then processes it appropriately.
Changing this setting from the control panel and then exiting the menus
causes the printer to restart. The menu selection is updated.
Serial Buffer
Disabled
Auto
3k to Sets the size of the serial input buffer
Notes:
Auto is the factory default setting.
The Disabled setting turns off job buffering. Any jobs already buffered on the
disk are printed before normal processing is resumed.
The serial buffer size setting can be changed in 1k increments.
The maximum size allowed depends on the amount of memory in the printer,
the size of the other link buffers, and whether Resource Save is set to On or
Off.
To increase the maximum size range for the Serial Buffer, disable or reduce
the size of the parallel, serial, and network buffers.
Changing this setting from the control panel and then exiting the menus
causes the printer to restart. The menu selection is updated.
Job Buffering
Off
On
AutoTemporarily stores jobs on the printer hard disk before printing
Notes:
Off is the factory default setting.
The Off setting does not buffer print jobs to the hard disk.
The On setting buffers jobs on the printer hard disk.
The Auto setting buffers print jobs only if the printer is busy processing data
from another input port.
Changing this setting from the control panel and then exiting the menus
causes the printer to restart. The menu selection is updated.
Understanding printer menus108
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
Serial Protocol
DTR
DTR/DSR
XON/XOFF
XON/XOFF/DTR
XONXOFF/DTRDSRSelects the hardware and software handshaking settings for the serial port
Notes:
DTR is the factory default setting.
DTR/DSR is a hardware handshaking setting.
XON/XOFF is a software handshaking setting.
XON/XOFF/DTR and XON/XOFF/DTR/DSR are combined hardware and
software handshaking settings.
Robust XON
On
OffDetermines whether or not the printer communicates availability to the computer
Notes:
Off is the factory default setting.
This menu item applies only to the serial port if Serial Protocol is set to
XON/XOFF.
Baud
1200
2400
4800
9600
19200
38400
57600
115200
138200
172800
230400
345600Specifies the rate at which data can be received through the serial port
Notes:
9600 is the factory default setting.
138200, 172800, 230400, and 345600 baud rates are only displayed in the
Standard Serial menu. These settings do not appear in the Serial Option 1,
Serial Option 2, or Serial Option 3 menus.
Data Bits
7
8Specifies the number of data bits that are sent in each transmission frame
Note: 8 is the factory default setting.
Parity
Even
Odd
None
IgnoreSets the parity for serial input and output data frames
Note: None is the factory default setting.
Honor DSR
On
OffDetermines whether the printer uses the DSR Signal. DSR is a handshaking signal used
by most serial cables.
Notes:
Off is the factory default setting.
The serial port uses DSR to distinguish data sent by the computer from data
created by electrical noise in the serial cable. The electrical noise can cause
stray characters to print. Select On to prevent stray characters from printing.
Understanding printer menus109
Downloaded From ManualsPrinter.com Manuals 
						

							NetWare menu
Menu itemDescription
View Login Name
Shows the assigned NetWare login name
View Print Mode
Shows the assigned NetWare print mode
View Network Number
Shows the assigned NetWare network number
Activate
On
OffActivates or deactivates NetWare support
Note: On is the factory default setting.
Ethernet 802.2
On
OffEnables the Ethernet 802.2 frame type setting
Note: On is the factory default setting.
Ethernet 802.3
On
OffEnables the Ethernet 802.3 frame type setting
Note: On is the factory default setting.
Ethernet Type II
On
OffEnables the Ethernet Type II frame type setting
Note: On is the factory default setting.
Ethernet SNAP
On
OffEnables the Ethernet Snap frame type setting
Note: On is the factory default setting.
Packet Burst
On
OffReduces network traffic by allowing the transfer and acknowledgement of
multiple data packets to and from the NetWare server
Note: Off is the factory default setting.
NSQ/GSQ Mode
On
OffSets the NSQ/GSQ Mode setting
Note: Off is the factory default setting.
AppleTalk menu
Menu itemDescription
View Name
Shows the assigned AppleTalk name
View Address
Shows the assigned AppleTalk address
Activate
Off
OnActivates or deactivates AppleTalk support
Note: On is the factory default setting.
Understanding printer menus110
Downloaded From ManualsPrinter.com Manuals