Land Rover Range Rover Classic Workshop 1995 Rover Manual
Have a look at the manual Land Rover Range Rover Classic Workshop 1995 Rover Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 364 Land Rover manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
GENERAL SPECIFICATION DATA 13 INFORMATION BRAKES Front service brake Type Outboard discs with four piston calipers................................................................................. Operation Hydraulic, servo assisted self-adjusting......................................................................... Pad material Ferodo 3440 non asbestos..................................................................... Rear service brake Type Outboard discs with two piston calipers................................................................................. Operation Hydraulic, servo assisted, self-adjusting......................................................................... Pad material Ferodo 3440 non asbestos..................................................................... Parking brake Type Mechanical-cable operated drum brake on the rear................................................................................. of the transfer gearbox output shaft Lining material Non asbestos.................................................................. Servo/master cylinder Manufacturer Lucas Girling.................................................................... Servo type LSC 115........................................................................ Master cylinder type AS/AS......................................................... Anti-lock brake system Manufacturer/type Wabco LRC M15 - 4 channel, 4 wheel sensed............................................................ integrated anti-lock brake system.
04GENERAL SPECIFICATION DATA 14 INFORMATION WHEELS AND TYRES Type and size Alloy 7.00J X 16................................................................... Tyre size 205R16 (tubeless).......................................................................... Type and size Steel 6.00JK X 16................................................................... Tyre size 205R16 (tubed).......................................................................... NOTE: Petrol vehicles must be fitted with S or T rated tyres. AIR CONDITIONING System CFC free expansion valve system (Nippon Denso)............................................................................. Compressor Nippon Denso 10PA17..................................................................... Fixed displacement swash plate WIPER MOTORS Tailgate wiper motor Make/type IMOS (non-serviceable)........................................................................ Running current, wet screen at 20°C ambient 1.0 to 2.8 amps................. Wiper speed, wet screen at 20°C ambient 37 to 43 cycles per minute....................... Windscreen wiper motor Make/type Lucas 28W 2-speed........................................................................ Running current (Link disconnected) 1.5 amps at 39 to 45 rev/min (normal speed)............................... Rotary link speed 60 to 73 rev/min (high speed).............................................................
GENERAL SPECIFICATION DATA 15 INFORMATION ELECTRICAL System 12 volt, negative ground............................................................................. Battery Make/type - basic Land Rover Parts and Equipment/Chloride............................................................. maintenance free 9-plate-210/85/90 Make/type - heavy duty Land Rover Parts and Equipment/Chloride.................................................... maintenance free 14-plate-380/120/90 Generator Manufacturer Magnetti Marelli.................................................................... Type A133 - 100A................................................................................. Polarity Negative ground............................................................................. Brush length New 20 mm......................................................................... Worn, minimum free protrusion from brush box 10 mm........................................................ Brush spring pressure flush with brush box face 136 to 279 g.............. Rectifier pack output rectification 6 diodes (3 positive side and 3 ground side)..................................... Field winding supply rectification 3 diodes...................................... Stator windings 3 phase-delta connected................................................................. Field winding rotor poles 12.................................................. Maximum speed 16,000 rev/min...................................................... Winding resistance at 20°C 2.6 ohms..................................... Control Field voltage sensed regulation............................................................................. Regulator-type 15 TR.................................................................. voltage 13.6 to 14.4 volts.................................................................... Nominal output Condition Hot................................................................. Generator speed 6000 rev/min..................................................... Control voltage 14 volt........................................................ Amp 100 amp......................................................................... Fuses Type Autofuse (blade type)................................................................................. blow ratings to suit individual circuits Horns Make/type Klamix (Mixo) TR99........................................................................ Starter motor V8 Engine Make/type Lucas M78R pre-engaged........................................................................ Minimum brush length 3.5 mm............................................. Minimum commutator diameter 28.8 mm............................... Diesel Engine Make and type Bosch 0.001.362.092.................................................................
04GENERAL SPECIFICATION DATA 16 INFORMATION REPLACEMENT BULBS REPLACEMENT BULBS TYPE Exterior lights Headlamps 12V 60/55W (Halogen) Auxiliary driving lamps 12V 55W H3 (Halogen) Sidelamps 12V 5W bayonet Tail lamps 12V 5/21W bayonet Reverse lamps 12V 21W bayonet Stop lamps 12V 21W bayonet Direction indicator lamps 12V 21W bayonet Rear side marker lamps 12V 4W bayonet Number plate lamps 12V 5W capless Interior lights Interior roof lamps 12V 10W Festoon Door shut face/puddle lamps 12V 5W capless Instrument panel lamps and warning lamps 14V 1.2W bulb/holder unit Ignition warning lamp (Instrument panel) 14V 2W capless SRS warning lamp (Instrument panel) 14V 1.4W capless Clock illumination 12V 2W bayonet Cigar lighter illumination 12V 1.2W capless Auxiliary switch illumination 12V 0.2W capless Auxiliary switch warning lamp 12V 0.2W capless Hazard warning switch illumination 14V 0.2W capless Automatic selector graphics illumination 12V 5W capless Heater/air conditioning graphics illumination 12V 1.2W capless CAUTION: The fitting of new bulbs with wattages in excess of those specified will result in damage to vehicle wiring and switches.
GENERAL SPECIFICATION DATA 17 INFORMATION VEHICLE WEIGHTS AND PAYLOAD When loading a vehicle to its maximum (Gross Vehicle Weight), consideration must be taken of the vehicle kerb weight and the distribution of the payload to ensure that axle loadings do not exceed the permitted maximum values. It is the customers responsibility to limit the vehicles payload in an appropriate manner such that neither maximum axle loads nor Gross Vehicle Weight are exceeded. Front Rear Total Basic models Axle kg Axle kg kg Manual V8 engine EEC Kerb weight 990 1080 2070 Gross Vehicle Weight* 1100 1510 2510 V8 engine SE EEC Kerb weight 1055 1095 2150 Gross Vehicle Weight* 1100 1510 2510 V8 engine LSE EEC Kerb weight 1090 1095 2185 (long wheelbase models) Gross Vehicle Weight* 1200 1620 2620 Diesel engine Tdi EEC Kerb weight 1040 1070 2110 Gross Vehicle Weight* 1200 1620 2620 Tdi SE EEC Kerb weight 1105 1085 2110 Gross Vehicle Weight* 1200 1620 2620 NOTE: EEC KERB WEIGHT is the minimum vehicle specification, plus full fuel tank and 75 kg driver. GROSS VEHICLE WEIGHT is the maximum all-up weight of the vehicle including driver, passengers, and equipment. This figure is liable to vary according to legal requirements in certain countries. Maximum roof rack load (including weight of rack) 75 kg must be included in total vehicle weight.
04GENERAL SPECIFICATION DATA 18 INFORMATION VEHICLE DIMENSIONS Overall length 4.48m................................................................... - Long wheelbase vehicles 4.68m...................................... Overall width 1.82m.................................................................... Overall height 1.80m................................................................... Wheelbase 2.54m....................................................................... - Long wheelbase vehicles 2.74m...................................... Track: front and rear 1.49m......................................................... Ground clearance: under differential 190mm................................ Turning circle 11.89m.................................................................... - Long wheelbase vehicles 13.64m...................................... Loading height 749mm................................................................. Maximum cargo height 1.028m..................................................... Rear opening height 0.87m......................................................... Usable luggage capacity, rear seat folded 2.00m 3....................... Usable luggage capacity, rear seat in use 1.03m3....................... TYRE PRESSURES Pressures: Check Normal on and off-road use. Off-road emergency soft use with tyres cold All speeds and loads maximum speed of 40 kph (25 mph) Front Rear (*) Front Rear bar 1.9 2.4 (2.6) 1.2 1.8 lbf/in 228 35 (38) 17 25 kgf/cm22.0 2.5 (2.7) 1.2 1.8 (*) Long wheelbase vehicles (2.74m, 108) The pressure of tyres must be increased be 0.3 bar (3 lbf in 20.2 kgf/cm2). For use with sustained driving speeds above 160 km/hr (100 miles/hour) or with heavy axle loads. Normal operating pressures should be restored as soon as reasonable road conditions or hard ground is reached. After any usage off the road, tyres and wheels should be inspected for damage particularly if high cruising speeds are subsequently to be used. Towing: When the vehicle is used for towing, the reduced rear tyre pressures for extra ride comfort are not applicable. WARNING: Vehicles fitted with tubeless alloy road wheels as original equipment, note that these wheels DO NOT accept inner tubes and tubed tyres MUST NOT be fitted.
ENGINE TUNING DATA 1 INFORMATION ENGINE - 3.9 V8 Type3.9 Litre V8 ................................................................................. Firing order1-8-4-3-6-5-7-2 ..................................................................... Cylinder Numbers Left bank 1-3-5-7.......................................................................... Right bank 2-4-6-8........................................................................ No 1 Cylinder locationPulley end of left bank ................................................... Timing marksOn crankshaft vibration damper .................................................................. Spark plugs Make/type(8.13:1 Compression) Champion RN11YCC...................................... Gap 0.84-0.96mm (0.033-0.038 in).................................................................................. Make/type(9.35:1 Compression) Champion RN11YCC...................................... Gap 0.84-0.96mm (0.033-0.038 in).................................................................................. Coil Make/type Bosch 0-221-122-392, (ETC 6574)........................................................................ Compression ratio8.13:1 or 9.35:1 ......................................................... Fuel injection systemLucas 14 CUX Hot-wire air flow sensor ..................................................... system electronically controlled Valve Timing Inlet Exhaust Opens 32°BTDC .............................................................................. 70°BBDC Closes 73°ABDC .............................................................................. 35°ATDC Duration 285° ........................................................................... 285° Valve peak 104°ATDC ....................................................................... 114°BTDC Idle speed - controlled by EFi system - all loads off in neutral 665 to 735 rev/min............................................ - auto gearbox in gear, air con operating 650±28 rev/min ................ - auto gearbox in gear, air con off 600±28 rev/min ........................... - manual gearbox 700±28 rev/min .................................................... - manual gearbox, air con operating 750±28 rev/min ....................... Base idle speed525±25 rev/min -. .............................................................. See FUEL SYSTEM, Fault diagnosis, Base Idle Speed Setting Ignition Timing - dynamic at 800 rev/min max, vacuum disconnected 8.13:1 compression, non catalyst 2°BTDC±1° ..................................... 9.35:1 compression, non catalyst 4°BTDC±1° ..................................... 9.35:1 compression, catalyst 5°BTDC±1° ............................................ Exhaust gas CO content at idle 0.5 to 1.0% max.............................................................
05ENGINE TUNING DATA 2 INFORMATION Distributor Make/type Lucas 35DLM8 electronic........................................................................ Rotation Clockwise............................................................................ Air gap 0.20-0.35mm.............................................................................. Part number Lucas Rover 8.13:1, non catalyst 42584A................................................. ERR 4753 9.35:1, non catalyst 42552A................................................. ERR 4754 9.35:1, catalyst 42583A........................................................ ERR 4755 Centrifugal Advance Decelerating check-vacuum hose disconnected Distributor rpm decelerating speeds 8.13:1 non catalyst 2000 Distributor advance........................................................................ 5°30 to 8°30 1400 ........................................................................ 6°18 to 8°30 800 .......................................................................... 2°to 4° 9.35:1 non catalyst 2200 Distributor advance........................................................................ 7°to 10° 1400 ........................................................................ 7°48 to 10° 650 .......................................................................... 1°to 3° 9.35:1 catalyst 2200 Distributor advance........................................................................ 5°30 to 8°30 1400 ........................................................................ 6°18 to 8°30 800 .......................................................................... 2°to 4° Fuel 8.13:1, non catalyst 91 RON minimum unleaded................................................. 9.35:1, non catalyst 95 RON minimum unleaded................................................. 9.35:1, catalyst 95 RON minimum unleaded........................................................ USA-Premium unleaded (PUG) CLC or AKI 90 octane minimum.............................. 95 RON minimum Australian market variations Fuel 91 RON minimum unleaded.................................................................................. Compression ratio 8.13:1............................................................ Spark plug Champion RN11YCC........................................................................ Spark plug gap 0.84-0.96mm (0.033-0.038 in)................................................................. Ignition Timing at 800 rev/min max (vacuum pipe disconnected) 2°BTDC±1° ............................................ Exhaust gas idle CO 1% max (hot)........................................................
ENGINE TUNING DATA 3 INFORMATION ENGINE - 4.2 V8 Type4.2 Litre V8 ................................................................................. Firing order1-8-4-3-6-5-7-2 ..................................................................... Cylinder Numbers Left bank 1-3-5-7.......................................................................... Right bank 2-4-6-8........................................................................ No 1 Cylinder locationPulley end of left bank ................................................... Timing marksOn crankshaft vibration damper .................................................................. Spark plugs Make/type Champion RN11YCC........................................................................ Gap 0.84-0.96mm (0.033-0.038 in).................................................................................. Coil Make/type Bosch 0-221-122-392, (ETC 6574)........................................................................ Compression ratio8.94:1 ......................................................... Fuel injection systemLucas 14 CUX Hot-wire air flow sensor system ..................................................... electronically controlled Valve Timing Inlet Exhaust Opens 28°BTDC ..................................................................... 72°BBDC Closes 64°ABDC ..................................................................... 20°ATDC Duration 272° .................................................................. 272° Valve peak 108°ATDC .............................................................. 116°BTDC Idle speed - controlled by EFi system - all loads off in neutral 665 to 735 rev/min............................................ -auto gearbox in gear, air con operating 650±28 rev/min ................. -auto gearbox in gear, air con off 600±28 rev/min ............................ -manual gearbox 700±28 rev/min ..................................................... -manual gearbox, air con operating 750±28 rev/min ........................ Base idle speed525±25 rev/min -. .............................................................. See FUEL SYSTEM, Fault diagnosis, Base Idle Speed Setting Ignition Timing Dynamic, vacuum disconnected 8°BTDC±1°at 800 rev/min max ............................. Exhaust gas CO content at idle 0.5 to 1.0% max.............................................................
05ENGINE TUNING DATA 4 INFORMATION Distributor Make/type Lucas 35DLM8 electronic........................................................................ Rotation Clockwise............................................................................ Air gap 0.20-0.35mm.............................................................................. Lucas 42510A............................................................................... Rover Part number ERR 0744........................................................... Centrifugal Advance Decelerating check-vacuum hose disconnected Distributor rpm decelerating speeds 2200 7°to 10° ........................................................................ 1400 7°48 to 10° ........................................................................ 800 1°to 3° .......................................................................... Fuel UK, Europe and Rest of World 95 RON minimum unleaded......................................... USA - Premium unleaded (PUG) CLC or AKI 90 octane minimum..................................... 95 RON minimum