Land Rover Range Rover Classic Workshop 1995 Rover Manual

							19FUEL SYSTEM
6
REPAIR FUEL FILTER ELEMENT
Service repair no - 19.25.07
Remove
1.Disconnect battery negative lead.
2.Clean area around filter head.
3.Place a suitable container beneath filter bowl to
collect any spillage.
4.Loosen bleed screw.
5.Loosen drain tap, allow fuel to drain into
container.
6.Unscrew filter element, discard element.
Refit
7.Clean seal and seating in filter head.
8.Lubricate filter element seal with fuel.
9.Position filter element to filter head and hand
tighten.
10.Reconnect battery negative lead.
11.Crank engine until fuel is drawn through the
system and starts.INTERCOOLER
Service repair no - 19.42.15
Remove
1.Disconnect battery negative lead.
2.Release 2 clips securing fan cowl to radiator top
cover.
3.Remove 4 bolts securing radiator top cover,
remove top cover.
4.Remove nut, bolt and washers securing
intercooler side cover bracket to bonnet [hood]
platform.
5.Release bracket from side cover lug, position
bracket and power steering reservoir aside.
6.Position side cover away from intercooler.
7.Loosen 2 clips and disconnect top hose from
intercooler.
8.Loosen 2 clips and disconnect bottom hose from
intercooler. 
						

							Tdi
7
REPAIR
9.Move intercooler upwards and clear of fan cowl.
Refit
10.Ensure locatiing lug grommets are fitted and in
good condition.
11.Ensure foam pad is in good condition and
attached to intercooler.
12.Move intercooler into position.
13.Reverse removal procedure.GLOW PLUGS
Service repair no - 19.60.31
Remove
1.Disconnect battery negative lead.
No.1 glow plug - air conditioning models
2.Release drive belt from compressor pulley.See
ENGINE, Repair, Drive Belt Renew
3.Remove 4 bolts securing compressor to front
cover, move compressor aside.
No.3 glow plug
4.Remove bolt securing Hummel valve, withdraw
valve, remove and discard O ring. 
						

							19FUEL SYSTEM
8
REPAIR
All glow plugs
5.Remove terminal nut from glow plug, disconnect
wire from glow plug terminal.
6.Remove glow plug.
Refit
7.Clean glow plug and seating.
8.Coat threads of glow plug with suitable anti-seize
compound operational to a temperature of
1000°C.
9.Fit glow plug. Tighten to
23 Nm.
10.Connect wire to glow plug terminal and secure
with nut.
NOTE: Feed wire must be connected to
No. 4 glow plug terminal.
11.
No. 3 glow plug:Lubricate new O ring with
engine oil and fit to Hummel valve. Fit valve and
secure with bolt. Tighten to
15 Nm.
No. 1 glow plug - air conditioning models
12.Position compressor to front cover, fit bolts.
Tighten to
25 Nm.
13.Fit drive belt to compressor pulley and adjust
tension.
See ENGINE, Repair, Drive Belt
Renew
All models
14.Reconnect battery negative lead.EGR VALVE
Service repair no - 19.45.01
Remove
1.Disconnect multiplug from EGR valve.
2.Disconnect vacuum pipe from EGR valve.
3.Remove 2 Allen screws securing EGR valve to
exhaust manifold.
4.Remove 2 bolts securing hose to EGR valve.
5.Remove EGR valve and discard gaskets.
Refit
6.Clean mating faces of EGR valve and exhaust
manifold.
7.Reverse removal procedure. Tighten bolts to
25
Nm. 
						

							Tdi
9
REPAIR GLOW PLUG CONTROL UNIT
Service repair no - 19.60.33
Remove
1.Disconnect battery negative lead.
2.Remove nut and bolt securing control unit to
mounting bracket.
3.Disconnect multiplug and remove control unit.
Refit
4.Reverse removal procedure.EGR CONTROL UNIT
Service repair no - 19.45.06
Remove
1.Release 2 glovebox stays from fascia and pivot
glovebox fully downwards.
2.Remove 2 plastic nuts securing control unit to
body.
3.Release control unit from fixings.
4.Disconnect multiplug and remove control unit.
Refit
5.Reverse removal procedure. 
						

							19FUEL SYSTEM
10
REPAIR EGR THROTTLE POSITION SENSOR
Service repair no - 19.30.14
Remove
1.Remove 2 screws securing throttle position
sensor mounting plate to injection pump.
2.Disconnect throttle position sensor multiplug
from harness.
3.Remove throttle position sensor assembly.
Refit
4.Locate throttle position sensor assembly on
injection pump and fit and tighten screws.
5.Connect multiplug.
6.Adjust throttle position sensor.
See
Adjustment, EGR Throttle Position sensor
INJECTORS
Service repair no - 19.60.10
Remove
1.Remove oil filler cap and remove sound
deadening pad from top of engine.
2.Remove high pressure pipe from relevant
injector and injection pump.
3.Disconnect spill return hose(s) from injector.
4.Plug pipes and injector connections to prevent
the ingress of dirt and foreign matter.
5.Remove nut securing injector clamp plate to
cylinder head.
6.Remove injector.
Refit
7.Reverse removal procedure. Renew copper
washer on injector. Tighten injector clamp plate
nut to
25 Nm. 
						

							Tdi
11
REPAIR FUEL INJECTION PUMP AND TIMING
Service repair no - 19.30.07
NOTE: The following text refers to a Tdi
vehicle with a manual gearbox without
electronic diesel control. Where reference
is made to the timing tool substitute the following
information for automatic and EDC variants.
If manual gearbox:Timing tool LRT-12-044 fits into
the base of the flywheel housing
If manual gearbox with EDC:Timing tool
LRT-12-085 must be used and also fits into the base
of the flywheel housing.
If automatic gearbox:Timing tool LRT-12-044 fits
into the larger bolt hole of coverplate on engine
backplate, sited near to the rear of sump. Pin locates
in ring gear.
Remove
1.Disconnect battery negative lead.
2.Remove injection pipes, pump to injector.
3.Remove oil filler cap from rocker cover.
4.Viewing valve mechanism through filler aperture,
turn crankshaft clockwise until No. 1 cylinder is
just before TDC.
5.Refit oil filler cap.
6.Remove blanking plug from flywheel housing.
7.Fit timing tool LRT-12-044 to flywheel housing,
do not engage centre pin.
8.Continue rotating crankshaft clockwise until
centre pin engages with timing slot in flywheel.
9.Remove injection pump access plate, complete
with gasket, from front cover plate.
10.Fit pin from LRT-12-045 to injection pump gear. 
						

							19FUEL SYSTEM
12
REPAIR 11.Remove drive gear to pump hub fixing bolts and
plate.
12.Remove pin from pump gear.
13.Fit gear retaining tool LRT-12-045 with an 8 mm
washer, 1.5 to 2 mm thick, under each bolt head
in addition to the existing washer.
14.Remove throttle cable and hand throttle cable if
fitted.15.Disconnect stop control solenoid connector.
16.Remove banjo bolts securing spill return, main
fuel and boost signal pipes, refit banjo bolts after
disconnecting pipes.
17.Remove pump mounting bracket bolts 2 off.
18.Loosen pump support bracket bolts to block,
sufficient for bracket to just move.
19.Remove pump securing nuts at flange and
withdraw pump and gasket.
20.Fit blanks to pipe connections. 
						

							Tdi
13
REPAIR Refit
21.Remove blanks from pump.
22.Remove special tool pin from pump.
23.Clean mating faces of pump and front cover.
24.Fit pump to cover with a new gasket and secure
with nuts. Tighten to
25 Nm.
25.Attach pump to bracket and finger tighten nuts
and bolts
26.First tighten bolts securing bracket to block and
then bolts securing pump to bracket.
27.Connect spill return, main fuel pipes. Tighten to
25 Nm.
28.Connect boost signal pipe and secure with banjo
bolts. Tighten to
10 Nm.
29.Connect stop control solenoid lead.
30.Connect throttle cable and where applicable
hand throttle cable.
31.Remove special tool LRT-12-045.
32.Fit gear lock plate.
33.Fit pin from special tool LRT-12-045.
34.Secure gear with bolts.
35.Remove special tool pin.
36.Turn crankshaft two complete revolutions, check
timing pin from LRT-12-045 can be fully and
easily inserted into the pump. At the same time
check flywheel timing pin LST-12-044 can also
be inserted in the flywheel slot.
37.If, with the flywheel timing pin located, the timing
pin cannot be inserted cleanly into the injection
pump, carry out the following:
(a) Ensure flywheel timing pin is disengaged
from slot in flywheel.
(b) Turn the crankshaft the small amount
necessary to enable the timing pin to be
inserted into the pump.
(c) Loosen the three pump gear retaining
bolts.
(d) Turn the crankshaft to T.D.C..
(e) Check that the timing pin is an easy fit in
the pump and that the flywheel timing pin
locates.
(f) Tighten the pump gear retaining bolts to
the correct torque.
(g) Remove the timing pin from the pump and
the timing tool from the flywheel housing.
38.Using antisieze compound, fit the blanking plug
to flywheel housing. Tighten to
12 Nm.
39.Fit access plate with gasket to front cover plate.
Tighten to
25 Nm.
40.Refit injector pipes. Tighten to29 Nm. 
						

							19FUEL SYSTEM
14
REPAIR VEHICLE SPEED SENSOR
Service repair no - 18.30.22
Remove
NOTE: The following procedure is carried
out with the ramp still raised.
1.Disconnect battery negative lead.
2.Disconnect sensor multi-plug.
3.Remove sensor retaining screw.
4.Remove sensor retaining plate.
5.Remove sensor from transfer box.
Refit
6.Reverse removal procedure.COOLANT TEMPERATURE SENSOR
Service repair no - 18.30.68
Remove
1.Disconnect battery negative lead.
2.Disconnect sensor multi-plug.
3.Remove sensor.
4.Clean off water spillage from sensor area.
Refit
5.Fit a new copper washer.
6.Fit sensor and tighten securely.
7.Refill cooling system.
8.Run engine, check for water leaks around
sensor. 
						

							MFI
1
DESCRIPTION AND OPERATION DESCRIPTION
Hot Wire Multiport Fuel Injection
The Hot Wire Multiport fuel injection system derives
its name from the mass air flow sensor which uses
one cold wire and one electrically heated wire to
measure the volume of air entering the engine.
The function of the system is to supply the exact
amount of fuel directly into the intake manifold
according to the prevailing engine operating
conditions.
To monitor these conditions, various sensors are fitted
to the engine to measure engine parameters. Data
from the sensors is received by the Engine control
module (ECM), the ECM will then determine the exact
amount of fuel required at any condition.
The ECM having received data from the sensors
produces pulses, the length of which will determine
the simultaneous open time of each bank of injectors
in turn, which will govern the amount of fuel injected.
Engine control module - ECM
The Multiport fuel injection system is controlled by the
14 CUX Engine Control Module comprising of a
microprocessor with integrated circuits and
components mounted on printed circuit boards. The
ECM is connected to the main harness by a 40 pin
plug.
Injectors
The eight fuel injectors are fitted between the
pressurized fuel rail and inlet manifold. Each injector
comprises a solenoid operated needle valve with a
movable plunger rigidly attached to the nozzle valve.
When the solenoid is energized the plunger is
attracted off its seat and allows pressurized fuel into
the intake manifold.Engine coolant temperature sensor
The engine coolant temperature sensor is located in
the front of the thermostat housing. The sensor
provides engine coolant information to the ECM. The
ECM increases the injector opening time when cold to
provide improved driveability, and reduces the
opening time as the engine reaches normal operating
temperature.
Engine fuel temperature sensor
The engine fuel temperature sensor is located in the
rail on the RH side of the ram housing. The sensor
sends fuel temperature data to the ECM, the ECM on
receiving the data will adjust the injector open time
accordingly to produce good hot starting in high
ambient temperatures.
Idle air control valve
The idle air control valve is screwed into a housing
attached to the rear of the plenum chamber, between
the plenum chamber and bulkhead. The idle air
control valve has two windings which enable the
motor to be energised in both directions thus opening
or closing the air valve as required by the ECM.
The idle air control valve will open and allow extra air
into the plenum chamber to maintain engine idle
speed when the engine is under increased (Electrical
and Mechanical) loads.
The idle air control valve will control engine idle speed
when the vehicle is stationary.
Heated oxygen sensors (0
2sensors) - Catalyst
vehicles
The two heated oxygen sensors are located forward
of the catalysts mounted in the exhaust downpipes.
The sensors monitor the oxygen content of the
exhaust gases and provide feedback information of
the air/fuel ratio to the ECM. Each sensor is heated by
an electrical element to improve its response time
when the ignition is switched on.