Land Rover Range Rover Body Repair Rover Manual

SUPPLEMENTARY RESTRAINT SYSTEM
7
REPAIR
30.Disconnect drivers air bag module connector.
Release connector and harness from clips.
31.Release 13 clips securing SRS harness to fascia
frame.
NOTE: Due to restricted access, two outer
clips A securing harness above heater
unit may have to be cut. Ensure that
location holes are clear. Collect loose ends of
clips.
32.Release 3 clips securing fascia harness trunking
to passenger side fascia frame.
33.Remove nut securing lower end of each blower
assembly to...

75SUPPLEMENTARY RESTRAINT SYSTEM NEW RANGE ROVER
8
REPAIR 47.Route SRS crash sensor harnesses through
bulkhead into wheel arches, locate harness
grommets.
48.Secure harness clips beneath wheel arches.
49.Route harnesses through valances into engine
bay. Locate harness grommets.
50.Raise battery tray and air cleaner for access.
Route crash sensor harnesses. Secure harness
clips.
51.Connect multiplugs to crash sensors.
52.Secure battery tray and air cleaner with bolts.
53.Connect SRS harness multiplug to...

SUPPLEMENTARY RESTRAINT SYSTEM
9
REPAIR AIRBAG MODULE - DRIVER SIDE
Service repair no - 76.73.71
Remove
1.Disconnect both battery terminals, negative lead
first.
2.Remove steering column nacelle.
See
STEERING, Repair.
3.Disconnect Supplementary Restraint System
(SRS) shorting link.
4.Unscrew 4 bolts (TX 30 Torx bit) securing
module to steering wheel.
NOTE: Fixings remain captive in steering
wheel.
NOTE: Rotate steering wheel for access to
all fixings.5.Release module from steering wheel, disconnect...

CHASSIS AND BODY
1
ADJUSTMENT FRONT DOOR
Service repair no - 76.28.07
NOTE: Adjustment should not be
necessary unless door or hinges have
been renewed.
Alignment of door to aperture.
1.Gain access to A post hinge bolts by removing
relevant wheel arch liner.
See Repair.
2.Slacken 2 bolts securing striker to B/C post.
3.Slacken 6 bolts securing door hinges to A post.
4.With assistance, adjust door position in aperture.
Tighten hinge bolts to
30 Nm. (22 lbf.ft)
Profile adjustment, door skin/frame to...

CHASSIS AND BODY
1
REPAIR BONNET
Service repair no - 76.16.01
Remove
1.Open bonnet.
2.Mark hinge outlines on bonnet.
3.Remove 2 hinge bolts from each side.
4.Disconnect washer tube at T piece on bonnet,
release tube from clip.
5.With assistance, release bonnet support struts at
lower ends.
6.With assistance, remove 2 remaining hinge bolts
and remove bonnet.
Refit
7.With assistance, fit bonnet. Fit, but do not tighten
bolts.
8.With assistance, connect bonnet support struts.
9.Connect washer tube, secure...

76CHASSIS AND BODY NEW RANGE ROVER
2
REPAIR BONNET LOCK PIN
Service repair no - 76.16.24
Remove
1.Remove bolts securing lock pin to bonnet.
2.Remove pin.
Refit
3.Position lock pin to bonnet.
4.Fit bolts but do not tighten.
5.Close and open bonnet to align pin.
6.Secure pin with bolts.
7.Lubricate pin.BONNET LOCK - LEFT HAND
Service repair no - 76.16.21
Remove
1.Remove bolts securing bonnet lock.
2.Release outer and inner cables from lock.
3.Remove lock.
Refit
4.Reverse removal procedure. 

CHASSIS AND BODY
3
REPAIR BONNET LOCK - RIGHT HAND
Service repair no - 76.16.25
Remove
1.Release 3 turnbuckles securing battery cover.
Remove cover
2.Remove 2 bolts securing bonnet lock to platform.
3.Manoeuvre lock and disconnect alarm switch
multiplug.
4.Release inner and outer cables from lock.
5.Remove lock.
Refit
6.Reverse removal procedure. 

76CHASSIS AND BODY NEW RANGE ROVER
4
REPAIR BONNET SAFETY CATCH
Service repair no - 76.16.34
Remove
1.Remove bolts securing safety catch to bonnet.
2.Remove safety catch.
Refit
3.Position catch to bonnet.
4.Fit bolts, do not tighten.
5.Close and open bonnet to align catch.
6.Secure catch with bolts.BONNET STRUT
Service repair no - 76.16.14
Remove
1.Support bonnet in open position.
2.Release clip securing strut lower ball joint.
3.Remove screws securing strut bracket to bonnet.
4.Remove strut and...

CHASSIS AND BODY
5
REPAIR CENTRE CONSOLE
Service repair no - 76.25.01
Remove
1.Remove electric window switch pack.
See
ELECTRICAL, Repair.
2.Disconnect rear footwell lamp multiplug.
3.Remove base in console bin.
4.Remove nuts securing rear of console to floor
studs.
5.Move both front seats fully rearward.
6.Remove 2 screws securing each side panel to
centre console. Release sprag clips from fascia
switch pack by firmly pulling rearwards. Remove
side panels.
7.Remove screw at rear of gear lever applique....

76CHASSIS AND BODY NEW RANGE ROVER
6
REPAIR 12.Remove 3 screws securing selector graphics
plate.
13.Raise selector graphics plate, disconnect
multiplug.
14.Remove selector graphics plate.
15. All models:
Remove clip securing park brake lever clevis pin,
remove clevis pin. Raise park brake lever to
vertical position.
16.Raise rear of console to disengage rear vent
ducts. Remove centre console.
Refit
17.Fit centre console, ensuring that ducts to rear
fresh air vents are correctly engaged.
18.Fit nuts...