Land Rover Freelander Owners Handbook Lrl 18 02 50 501 Rover

							Tires
211
The lower label contains the following 
information:
•The maximum number of occupants (1), 
divided between the front (2) and rear (3) of 
the vehicle.
•The vehicle capacity weight (4), which 
includes the weight of the driver, 
passengers and cargo.
•Cold inflation pressures for the spare tire (5) 
and the front and rear tires (6).
•The size of the tires (7) with which the 
vehicle was originally equipped.
NOTE: The label must not be changed, even if 
different wheels are fitted at a later stage.Tire pressure label/placard (Canada only)
A tire information label is visible on the pillar 
behind the driver’s door (also known as the B 
pillar).
The label contains information relating to tire 
and wheel sizes and recommended pressures 
for all wheel and tire combinations fitted to the 
Freelander.
NOTE: The label must not be changed, even if 
different wheels are fitted at a later stage.
H5796C
LANDROVERDATE :  MM/YYGVWR/PNBV :2060KG    (
 4542LB )ICES/NMB - 002
GAWR FRONT/PNBE AVANT :     1080KG   (
 2381LB )TIRES/ RIMS/PRESSURE (
COLD)
 /PNEUSJANTESPRESSION (
A FROID)
 /195/80R155.5JX15207KPA(
30PSI)
 (
30LB/PO2
)215/65R166.0JX16207KPA(30PSI) (30LB/PO2
)225/55R177.0JX17207KPA(30PSI) (30LB/PO2
)235/50R187.0JX18207KPA(30PSI) (30LB/PO2
)
GAWR REAR/PNBE ARRIER :     1120KG   (
 2469LB )TIRES/ RIMS/PRESSURE (
COLD)
 /PNEUSJANTESPRESSION (
A FROID)
 /
VIN :TYPE :TESTVIN1234567890MPV/VTUM
195/80R155.5JX15207KPA(
30PSI)
 (
30LB/PO2
)215/65R166.0JX16207KPA(30PSI) (30LB/PO2
)225/55R177.0JX17207KPA(30PSI) (30LB/PO2
)235/50R187.0JX18207KPA(30PSI) (30LB/PO2
) 
						

							Tires
212
UNIFORM TIRE QUALITY GRADING
United States Department of 
Transportation/Uniform Tire Quality Grades
The following information relates to the tire 
grading system developed by the National 
Highway Traffic Safety Administration which 
will grade tires by tread wear, traction and 
temperature performance.
NOTE: Tires that have deep tread, and winter 
tires, are exempt from these marking 
requirements.
Quality grades, where applicable, can be found 
on the tire sidewall between the tread shoulder 
and maximum section width.
For example:
In addition to the marking requirements, 
passenger car tires must conform to Federal 
Safety Requirements.
Treadwear
The treadwear grade is a comparative rating 
based on the wear rate of the tire when tested 
under controlled conditions on a specified 
government test course.
For example; a tire graded 150 would wear one 
and a half times as well on a government test 
course as a tire graded 100. However, the 
relative performance of tires depends on the 
actual conditions of their use, and may depart 
significantly from the norm due to variations in; 
driving habits, service practices, and 
differences in road characteristics and climate.
Traction
The traction grades, from highest to lowest, 
are; AA, A, B, and C. These grades represent a 
tire’s ability to stop on a wet pavement as 
measured under controlled conditions on 
specified government test surfaces of asphalt 
and concrete.WARNING
The traction grade assigned to a tire is based 
on straight-ahead braking tests, and does not 
include; acceleration, cornering, 
hydroplaning. or peak traction 
characteristics.
Temperature
The temperature grades, from highest to 
lowest, are, A, B, and C. These grades represent 
a tires resistance to the generation of heat, and 
its ability to dissipate heat, when tested under 
controlled conditions on an indoor laboratory 
test wheel.
Sustained high temperatures can cause the 
material of a tire to degenerate, and reduce the 
tire life, and excessive temperature can lead to 
sudden tire failure.
C grade is the minimum performance level 
which all passenger car tires must meet under 
the Federal Motor Safety Standard (FMVSS) 
109.
Grades B and A represent higher levels of 
performance on the laboratory test than the 
minimum required by law.
WARNING
The temperature grade for a tire is 
established with the correct loading and 
inflation pressure. Excessive speed, under 
inflation, or overloading, either separately, 
or in combination, can cause heat build up 
and possible tire failure.
Treadwear 200 Traction AA Temperature A 
						

							Tires
213
PRODUCTION OPTION WEIGHTS
(USA only)
This table lists the production options weights. 
To calculate the curb weight of your vehicle, 
add the weight of all production options to the 
basic curb weight for your vehicle.
NOTE: The table only lists optional equipment 
that weigh more than 3 lb (1.4 kg). WARNING
Do not exceed the vehicle capacity weight 
(the total weight of driver, passengers and 
cargo) given on the tire information label (see 
page 
Weight
lb kg
Curb weight, no options fitted
3 door KV6 Auto 3663 1665
5 door KV6 Base Auto 3564 1620
5 door KV6 SE Auto 3630 1650
5 door KV6 HSE Auto 3652 1660
Production options
Front and rear mud flaps 4.4 2.0
Leather trim 4.4 2.0
Sunroof 24.4 11.1
Roof rails 18.5 8.4
Loadspace cover 4.4 2.0
Power amplifier and nine speakers 15.4 7.0 
						

							Tires
214
Steps for determining correct load limit
WARNING
Do not exceed the vehicle capacity weight 
(the total weight of driver, passengers and 
cargo) given (see ‘TIRE INFORMATION 
LABELS’, page 210).
1.Locate the statement The combined 
weight of occupants and cargo should 
never exceed XXXX kg or XXXX lb on your 
vehicle’s placard (see page 210).
2.Determine the combined weight of the 
driver and passengers that will be riding in 
your vehicle.
3.Subtract the combined weight of the driver 
and passengers from XXXX kg or XXXX lb 
(weight given on placard).
4.The resulting figure equals the available 
amount of cargo and luggage load 
capacity. For example, if the XXXX 
amount equals 1400 lb, and there will be 
five 150 lb passengers in your vehicle, the 
amount of available cargo and luggage 
load capacity is 650 lb: 
(5 x 150 = 750, and 
1400 - 750 = 650 lb).
5.Determine the combined weight of 
luggage and cargo being loaded on the 
vehicle. That weight may not safely exceed 
the available cargo and luggage load 
capacity calculated in Step 4.
6.If your vehicle will be towing a trailer, load 
from your trailer will be transferred to your 
vehicle. Consult this handbook to 
determine how this reduces the available 
cargo and luggage load capacity of your 
vehicle. (Subtract the trailer nose load 
(see page 159) from the available cargo 
and luggage load capacity.)The number and weight of passengers will 
affect the cargo and luggage load capacity. In 
the example above, the cargo and luggage load 
capacity is 650 lb. However, if fewer 
passengers ride in the vehicle, the luggage load 
capacity will increase. If this vehicle carries 
three 150 lb passengers, the cargo and luggage 
load capacity will increase to 950 lb: 
(3 x 150 = 450 lb, and 1400 - 450 = 950 lb).
If the passengers weigh more, the cargo and 
luggage load capacity will decrease.
WARNING
The weight of accessories must also be 
subtracted from the available cargo and 
luggage load capacity. If you are unsure of the 
weight of any accessories fitted to your 
vehicle, contact your Land Rover Retailer.
Overloading the vehicle will have an adverse 
affect on braking and handling 
characteristics, which could compromise 
your safety. Overloading a vehicle may also 
cause tire damage or failure. 
Never overload your vehicle. 
						

							Tires
215
TIRE GLOSSARY
Cold tire pressure:
Pressure in a tire that has been driven for less 
than one mile or has been standing for three 
hours or more.
Maximum inflation pressure:
Maximum air pressure, to which a cold tire may 
be inflated, this figure (in psi and kPa) is 
moulded onto the sidewall of a tire.
Curb weight:
The weight of a motor vehicle with standard 
equipment including the maximum capacity of 
fuel, oil, coolant and if so equipped, air 
conditioning and additional weight of optional 
engine.
Accessory weight:
The combined weight (in excess of those 
standard items which may be replaced) of 
automatic transmission, power steering, power 
brakes, power windows, power seats, radio and 
heater, to the extent that these items are 
available as factory-installed equipment 
(whether installed or not).
Production options weight:
The combined weight of those installed 
production options weighing over 3 lb (1.4 kg) 
in excess of those standard items which they 
replace, not previously considered in curb 
weight or accessory weight, including heavy 
duty brakes, ride levellers, roof rack, heavy duty 
battery and special trim.Vehicle capacity weight:
The rated cargo and luggage load plus 150.0 lb 
(68.0 kg) times the vehicle’s designated seating 
capacity.
Maximum loaded vehicle weight:
This is the sum of:
•Curb weight.
•Accessory weight.
•Vehicle capacity weight.
•Production options weight.
Rim:
A metal support for a tire or a tire and tube 
assembly upon which the tire beads are seated.
Bead:
The part of the tire that is made of steel wires, 
wrapped or reinforced by ply cords and that is 
shaped to fit the rim. 
						

							Cleaning & Vehicle Care
216
Clea ning  & Ve hicle C areWASHING YOUR VEHICLE
WARNING
Some high pressure cleaning systems are 
sufficiently powerful to penetrate door and 
window seals and damage rubbing strips and 
locking mechanisms. Never aim the water jet 
directly at heater air intakes, body and 
sunroof seals, the softback canopy, or at any 
components that might easily be damaged.
Read individual product warnings before 
using any car cleaning or washing products.
If the vehicle is particularly dirty, use a hose to 
flush grime and grit from the painted surfaces, 
prior to washing. Then, wash the vehicle using 
cold or lukewarm water containing a good 
quality wash and wax shampoo. Always use 
plenty of water to ensure that grit is flushed 
from the surface and not ground into the 
paintwork. After washing, rinse the vehicle with 
clean water and dry off with a chamois leather.
•Do not use hot water.
•Do not use detergent soap products or 
washing-up liquid.
•In hot weather, do not wash the vehicle in 
direct sunlight.When using a hose, do not direct the jet into the 
heater air intake ducts, or through the wheel 
trim apertures onto the brake components, or 
at the door, window or sunroof seals, or at the 
soft-back canopy
* where water pressure could 
penetrate the seals.
Automatic car wash
If using an automatic car wash (5-door 
models), remove the radio aerial before 
entering the car wash. 
NOTE: DO NOT wash a 3-door model equipped 
with a soft-back canopy in an automatic car 
wash.
Removing tar spots
Use white spirit to remove tar spots and 
stubborn grease stains from paintwork. Then 
wash immediately with soapy water to remove 
all traces of spirit.
Underbody maintenance
Corrosive materials used for snow and ice 
removal and dust control can collect on 
underbody parts. If these materials are not 
removed, accelerated rusting can occur. Use a 
hose to regularly flush the underbody with plain 
water, taking particular care to thoroughly clean 
those areas where mud and other debris can 
easily collect. 
Similarly, after off-road driving or wading in 
muddy or salt water conditions, use a hose to 
wash underbody components and other 
exposed parts of the vehicle.
H5215 
						

							Cleaning & Vehicle Care
217
Steam cleaning
Before steam cleaning the engine, cover the 
power steering reservoir to prevent 
contamination of fluid and ensure the covers 
and seals of electrical components are in place. 
After steam cleaning carefully re-wax the 
metallic components, especially the steering 
column, engine coolant pipes, hose clips and 
the ignition coil clamp, to prevent corrosion.
WARNING
Do not direct high temperature or high 
pressure steam or water onto electrical wiring 
or components.
Softback canopy and hardback
•Use a soft brush to remove dust and flaking 
dirt from the canopy or hardback (not the 
windows), then soak with a mild soap and 
water solution to soften encrusted dirt and 
remove stains, prior to washing.
•Wash using a mild soap and water solution, 
before rinsing the canopy or hardback with 
clean lukewarm or cold water. Rinse until all 
traces of soap are removed.
•Never use spirit, petrol or chlorine based 
cleaning agents, or wash/wax compounds 
to clean the canopy, hardback and windows 
- wax polishes will become ingrained in the 
textured finish.
•Never use an automatic car wash, or a high 
pressure hose.
•Do not aim jets of water at zips or seals.
•Ensure the canopy is dry before folding or 
removing.
•Improper cleaning and lack of care may 
cause damage to the canopy and window 
panels, resulting in water penetration.Softback or hardback windows
WARNING
DO NOT use abrasive or solvent cleaners on 
the canopy or hardback and especially NOT on 
the window panels. Use only mild detergents.
•Wipe off any dust or dirt using a damp soft 
cloth.
•DO NOT wipe the window panels when they 
are dry.
•Wash the windows with a clean, grit-free 
sponge or cloth and a mixture of a mild 
detergent and cold or lukewarm water. 
Rinse the window panels thoroughly and 
wipe with a soft moist cloth.
NOTE: The removable window panels fitted 
to the softback, are susceptible to 
scratching from the effects of dirt and grit. 
For this reason, it is important to wash them 
frequently.
•Remove frost, ice and snow using lukewarm 
water - do not use a scraper. Take care when 
clearing ice or snow from the window 
panels, as they are easily scratched and 
could crack at low temperatures.
•Do not put adhesive backed material 
(badges, stickers etc) onto the window 
panels - this may result in damage and 
discolouration.
Body protection
After washing, inspect the paintwork for 
damage. Any stone chips, fractures or deep 
scratches in the bodywork should be repaired 
promptly. Bare metal will corrode quickly and 
can develop into major repair expense. 
Minor chips and scratches can be repaired with 
touch-up materials available from your dealer. 
Larger areas of damage need to be corrected to 
professional standards immediately. 
						

							Cleaning & Vehicle Care
218
Polishing
Occasionally treat the paint surface with an 
approved polish containing the following 
properties:
•Very mild abrasives to remove surface 
contamination without removing or 
damaging the paint.
•Filling compounds that will fill scratches and 
reduce their visibility.
•Wax to provide a protective coating between 
the paint and the elements.
NOTE: DO NOT apply wax polish to the roof 
panels
*, or to the bumper mouldings - polish 
will become ingrained in the textured finished.
Windows and mirrors
Regularly clean all windows and mirrors, inside 
and out, using an approved glass cleaner.
Windshield: In particular, clean the outside of 
the screen with glass cleaner after washing the 
vehicle with wash and wax products, and before 
fitting new wiper blades.
Rear window: Clean the inside with a soft cloth, 
using a side to side motion to avoid damaging 
the heating elements. DO NOT scrape the glass 
or use abrasive cleaners - this will damage the 
heating elements.
Mirrors: Wash with soapy water. Use a plastic 
scraper to remove ice. DO NOT use abrasive 
cleaners or metal scrapers.
Wiper blades
Wash in warm soapy water. DO NOT use spirit 
or gasoline based cleaners. 
						

							Cleaning & Vehicle Care
219
CLEANING THE INTERIOR
WARNING
Read individual product warnings before 
using any car cleaning or washing products.
Plastic materials
Clean plastic-faced or cloth covered surfaces 
with warm water and a non-detergent soap and 
wipe with a clean cloth.
NOTE: DO NOT polish facia components - for 
safety, these should remain non-reflective.
Leather
Leather seats, steering wheel and trim features 
should be cleaned with warm water and a 
non-detergent soap. Dry and polish the leather 
with a dry, lint-free cloth.
NOTE: DO NOT use gasoline, detergents, 
furniture creams or polishes.
Carpet and fabrics
Clean with diluted nylon upholstery cleaner - 
test a concealed area first.
Instrument pack, clock and radio
Use a clean cloth which has been moistened 
slightly with water.
WARNING
Do not use chemicals or household cleaners. 
Keep fluids and liquids of all kinds away from 
the radio.
Facia mounted rubber mats
The mats are removable for cleaning - replace 
with care.Seat belts
Extend the belts, then use warm water and a 
non-detergent soap to clean. Allow the belts to 
dry naturally, and do not retract them or use the 
vehicle until they are completely dry.
WARNING
DO NOT use bleaches, dyes or cleaning 
solvents on seat belts.
Airbag module covers
WARNING
To prevent airbag SRS damage, the steering 
wheel centre pad and other areas containing 
airbags should ONLY be cleaned sparingly 
with a damp cloth, warm water and a 
non-detergent soap.
DO NOT allow these areas to be flooded with 
liquid, and DO NOT use gasoline, detergent, 
furniture cream or polishes. 
						

							Identification Numbers
220
Identification NumbersCONTACTING YOUR DEALER
When communicating with your Retailer, 
always quote the Vehicle Identification Number 
(VIN). If your communication concerns the 
engine or gearbox, it may be necessary to quote 
these numbers as well.
IDENTIFICATION NUMBER LOCATIONS
1.Vehicle identification number (VIN)
2.Engine Number
 Stamped vertically into the right side of 
the cylinder block (when viewed from the 
front).
3.Gearbox number
On a label attached to the upper face of the 
gearbox housing.
WARNING
DO NOT exceed the gross weight or axle loads 
stated on the certification label attached to 
the vehicle. Exceeding allowable vehicle and 
axle loads will increase the risk of tire or 
suspension failure, increase vehicle brake 
stopping distance, and adversely affect 
vehicle handling and stability which may 
result in a crash or rollover.
VEHICLE IDENTIFICATION NUMBER
The VIN (and recommended maximum vehicle 
weights) is stamped on a plate at the foot of the 
left hand door pillar and also stamped into the 
bulkhead, at the top, inside the engine 
compartment. In addition, as a deterrent to car 
thieves and to help the police, the VIN is 
stamped into a plate, visible at the bottom left 
hand corner of the windscreen.
H512123
11
TIRE AND LOADING INFORMATION
SEE OWNER’S
MANUAL FOR
ADDITIONAL
INFORMATION
SEATING CAPACITYTOTAL 5FRONT  2 REAR  3 
ORIGINAL TIRE SIZE COLD TIRE INFLATION PRESSURE
FRONT
REAR
COLD TIRE INFLATION PRESSURE
COMPACT SPARE TIRE235/50R18
T195/80R15207kpa,  30PSI
207kpa,  30PSI
207kpa,  30PSI
The combined weight of occupants and cargo should never exceed 387kg or 853lbs
RTC500490
H5795N
MFD   BY   LANDROVER   IN   THE   UKDATE : MM/YYGVWR:  2060KG  (4542LB)
TESTMARK1234567890
TYPE :  MPV
THIS VEHICLE CONFORMS TO ALL APPLICABLE
U.S.FEDERAL MOTOR VEHICLE SAFETY AND
THEFT PREVENTION STANDARDS IN EFFECT ON
THE DATE OF MANUFACTURE SHOWN ABOVE
GAWR FRONT: 1080KG  (2381LB)
GAWR REAR: 1120KG  (2469LB)195/80R15 TIRES, 5.5JX15 RIMS, AT 207KPA (30PSI) COLD
215/65R16 TIRES, 6.0JX16 RIMS, AT 207KPA (30PSI) COLD
225/55R17 TIRES, 7.0JX17 RIMS, AT 207KPA (30PSI) COLD
255/50R18 TIRES, 7.0JX18 RIMS, AT 207KPA (30PSI) COLD
195/80R15 TIRES, 5.5JX15 RIMS, AT 207KPA (30PSI) COLD
215/65R16 TIRES, 6.0JX16 RIMS, AT 207KPA (30PSI) COLD
225/55R17 TIRES, 7.0JX17 RIMS, AT 207KPA (30PSI) COLD
255/50R18 TIRES, 7.0JX18 RIMS, AT 207KPA (30PSI) COLD
PAINT :  XXX TRIM :  XXX