Land Rover Defender 300tdi Workshop 3rd Edition Rover Manual

WHEELS AND TYRES
5
REPAIR Off Vehicle Balancing
Balance wheel assembly referring to equipment
manufacturers instructions.
It is essential that the wheel is located by the centre
holeNOTthe stud holes. To ensure positive wheel
location the diameter of the locating collar on the
machine shaft must be 112,80 to 112,85 mm (4.441 to
4.443 in). This diameter will ensure that the collar fits
correctly within the centre hole of the wheel.
Where possible, always use the vehicle wheel
retaining nuts to locate the...

74WHEELS AND TYRES
6
REPAIRREV: 05/99 WHEELS
Remove
WARNING: The parking brake acts on
transmission, not rear wheels, and may
not hold vehicle when jacking unless
following procedure is used. If one front wheel
and one rear wheel is raised no vehicle holding or
braking effect is possible. Wheels MUST be
chocked in all circumstances.
Apply parking brake, select a gear in main
gearbox and engage low gear in transfer box.
1.Loosen 5 wheel nuts.
2.Using a suitable trolley jack, raise vehicle and
place on...

WHEELS AND TYRES
7
REPAIR REV: 05/99 WHEEL STUD
Remove
1.Remove wheel
See Wheels.
2.Drive stud out of driveshaft flange.
Refit
3.Position stud in flange.
4.Install a suitable spacer over stud.
5.Using a M16 x 1.5 nut, a slave wheel nut is
suitable, pull stud into flange until shoulder of
stud abuts flange.
6.Refit wheel.
See Wheels 

CHASSIS AND BODY
1
DESCRIPTION AND OPERATION CHASSIS AND BODY
Chassis
The chassis on all Defender variants are of the box
section, ladder type construction, manufactured from
2 mm (14swg) steel and treated with zinc phosphate,
cathodic electro coated, followed by waxing in the rear
crossmember.
Outriggers and angled brackets welded to the chassis
support suspension and axle components and are
also used as body mounting points. A detachable box
section crossmember, located between the two
chassis...

76CHASSIS AND BODY
2
DESCRIPTION AND OPERATION LAND ROVER 90 

CHASSIS AND BODY
3
DESCRIPTION AND OPERATION LAND ROVER 90
CHASSIS ALIGNMENT DIMENSIONS
A - Front Datum
B - Chassis Datum
C - Front axle centre line
D - Rear axle centre line
1.239,0 - 236,5 mm
2.82,0 - 79,5 mm
3.633 mm
4.2420,6 - 2418,6 mm
5.2306,4 - 2305,4 mm
6.981,2 - 978,7 mm
7.182,7 mm
8.41,5 - 37,0 mm
9.252 - 250 mm10.110 mm
11.2360mm - Wheelbase
12.636 - 634 mm
13.488 - 483 mm
14.488 - 483 mm
15.3431,1 - 3426,1 mm
16.588,3 - 586,3 mm
17.2313,8 - 2311,8 mm
18.590,5 mm
19.295,25 mm
20.519,60 -...

76CHASSIS AND BODY
4
DESCRIPTION AND OPERATION LAND ROVER 110 

CHASSIS AND BODY
5
DESCRIPTION AND OPERATION LAND ROVER 110
CHASSIS ALIGNMENT DIMENSIONS
A - Front Datum
B - Chassis Datum
C - Front axle centre line
D - Rear axle centre line
1.4148 - 4143 mm
2.4009,5 - 4005 mm
3.978,7 - 981,2 mm
4.22 - 20 mm
5.252 - 250 mm
6.239 - 236,5 mm
7.3023,3 - 3022,3 mm
8.3030,7 - 3028,7 mm
9.155 - 153 mm
10.871,2 - 869,2 mm
11.2794 mm - Wheelbase
12.488 - 483 mm13.488 - 483 mm
14.82 - 79,5 mm
15.750,9 mm
16.750,9 mm
17.439,5 - 436,5 mm
18.439,5 - 436,5 mm
19.299,5 - 295,5 mm...

76CHASSIS AND BODY
6
DESCRIPTION AND OPERATION LAND ROVER 130 

CHASSIS AND BODY
7
DESCRIPTION AND OPERATION LAND ROVER 130
CHASSIS ALIGNMENT DIMENSIONS
A - Front Datum
B - Chassis Datum
C - Front axle centre line
D - Rear axle centre line
E - Chassis Datum, section A - A
1.633,0 mm reference only
2.3569,3 - 3567,3 mm
3.2421,8 - 2419,8 mm
4.2317,5 - 2314,5 mm
5.2188,3 - 2185,3 mm
6.2119,5 - 2117,3 mm7.1990 - 1988 mm
8.1970 - 1968 mm
9.2401,8 - 2399,8 mm
10.110,0 mm reference
11.149,7 - 146,7 mm reference dimension
NOTE: The above dimensions are for the Land Rover 130...