Kyocera TASKalfa 300i User Manual

Basic Operation
3-7
3
Adjusting Density
Use this procedure to adjust the density when copying.
NOTE: You may choose Auto mode as the default setting (refer to  Density on page 8-18).
The procedure for adjusting the dens ity of copies is explained below.
1Press the Copy key.
2Place the originals on the platen.
3Set the original on the platen and press [Image 
Quality] -> [Density].
4Adjust density manually pressing [-3] (Lighter) to 
[+3] (Darker). You can change the density level [-3] 
(Lighter) to [+3]...

Basic Operation
3-8
Selecting Image Quality
Select image quality suited to the type of original.
The table below shows the quality options.
The procedure for selecting the quality of copies is explained below.
1Press the Copy key.
2Place the originals on the platen.
3Set the original on the platen and press [Image 
Quality] -> [Original Image].
4Select the image quality.
5Press [OK].
6Press the  Start key. Copying begins.
Image Quality Option Description
Text+Photo For originals with both text and...

Basic Operation
3-9
3
Zoom Copying
Adjust the magnification to reduce or enlarge the original image. The following zoom options are available.
Auto ZoomAutomatically reduces or enlarges the original image 
suitably to the selected paper size.
Manual Zoom Manually reduces or enlarges the original image in 1% 
increments between 25% and 400%.
Preset Zoom
Reduces or enlarges at preset magnifications.
The following magnificat ions are available.
Letter-RLedger: 129 %
Statement-R: 64 % A3: 141 %
A5: 70 %
A4...

Basic Operation
3-10
XY Zoom
Select vertical and horizontal magnifications 
individually. Reduce or enlarge original images in 1% 
increments between 25% and 400%.
The procedure for using zoom copying is explained below.
1Press the  Copy key.
2Place the originals on the platen.
3Set the original on the platen and press [Layout/
Edit] -> [Zoom].
4Press [Standard Zoom] to use Auto Zoom.
Press [+] or [–] to change the displayed 
magnification as desired. You can also enter the 
magnification directly using...

Basic Operation
3-11
3
Duplex Copying
Produce two-sided copies. The following duplex options are available.
You can also create single-sided copies from two-sided originals or originals with facing pages such as books. 
The following modes are available.
One-sided to Two-sidedProduces two-sided copies from one-sided originals. In 
case of an odd number of originals, the back side of the 
last copy will be blank.
The following binding options are available.
A Original Left/Right to Binding Left/Right:...

Basic Operation
3-12
Book to One-sided
Produces a 1-sided copy of a 2-sided or open book 
original.
The following binding options are available.
•Binding Left : Originals with facing pages are 
copied from left to right.
• Binding Right : Originals with facing pages are 
copied from right to left.
NOTE: The following sizes of originals and paper are 
supported in Two-sided to One-sided and Book to One-
sided. Original: Ledger, Letter-R, A3, B4, A4-R, B5-R, 
A5-R and 8K. Paper: Letter, A4, B5 and 16K. You...

Basic Operation
3-13
3
6If you choose [2-sided>>1-sided], 
[2-sided>>2-sided], [Book>>1-sided] or 
[Book>>2-sided], select the binding edge of the 
originals of Original.
7Press [Original Orientation] to select orientation of 
the originals, either [Top Edge Top] or [Top Edge 
Left]. Then press [OK].
8Press [OK].
9Press the  Start key.
Once an original placed on the platen is scanned, 
replace it with the next one. Then, press the Start  
key.
After scanning all originals, press [Finish Scan] to 
start...

Basic Operation
3-14
With Document Finisher
When you use offsetting, printed copies are segregated 
after each set of copies (or after each page).
NOTE: The optional document finisher is required.
The procedure for using collate/offset copying is 
explained below.
1Press the  Copy key.
2Place the originals on the platen.
3Press [Org./Paper/Finishing] and then [Collate/
Offset].
4To use collate copying, press [On] of  Collate.
To use offset copying, press [Each Set] of  Offset.
Press [OK].
If [Off] is...

Basic Operation
3-15
3
Reserve Next
This function allows you to reserve the next job during printing. Using this  function, the original will be scanned 
while the machine is printing. When th e current print job ends, the reserved copy job is printed. The procedure 
differs depending on the  Reserve Next Priority (refer to page 8-26 ).
If  Reserve Next Priority is set to [On]
The Copy function default screen appear s on the touch panel during printing.
1Place the originals onto the machine for reserving...

Basic Operation
3-16
Interrupt Copy
This function allows you to pause the current jobs in progress when you need to make copies immediately.
When interruption copy ends, the machine resumes the paused print jobs.
NOTE: You can change the delay until interrupt copying is cancelled. Change the delay as required. For more 
information, refer to Interrupt Clear Timer on page 8-50 .
1Press the Interrupt key.
Ready for interrupt copy.  is displayed.
The current print job is temporarily interrupted.
2Place the...