Konica Minolta magicolor 4695MF User Manual

Hard Disk Kit 307
Hard Disk Kit
If you install a hard disk kit, the followings can be performed:
„Job printing/saving
„Fonts/forms/color profile download
„User Authentication
„Direct printing
A hard disk kit and a CF adapter cannot be installed simultaneously.
Installing the Hard Disk kit
Note
Its very important to protect the printer controller board and any 
associated circuit boards from electrostatic damage. Before performing 
this procedure, review the antistatic caution on page 303. In addition,...

Hard Disk Kit 308
2Remove the rear cover.
3Using a screwdriver, loosen the 
screw.
Do not remove any screw 
other than the one indicated 
in the illustration.
4Open the inside cover.
Downloaded From ManualsPrinter.com Manuals 

Hard Disk Kit 309
5Plug the cable on the hard disk 
kit into the connector on the con-
troller board.
6Insert the three mounting pins 
on the hard disk kit into the holes 
in the controller board to mount 
the hard disk kit onto the control-
ler board.
7Close the inside cover, and then tighten the screw.
8Close the rear cover.
9Reconnect all interface cables.
Downloaded From ManualsPrinter.com Manuals 

Hard Disk Kit 310
10Reconnect the power cord, and 
turn on the machine.
11Declare the Hard Disk in the Windows printer driver (Properties/Configure 
tab).
Downloaded From ManualsPrinter.com Manuals 

CompactFlash 311
CompactFlash
If you install a CompactFlash card, the followings can be performed:
„Fonts/forms/color profiles download
„User Authentication
„Direct printing (including the use of PageScope Direct Print)
Only CompactFlash cards with a capacity of 512 MB, 1 GB, 2GB or 
4GB can be used.
The job printing/saving function is not available with a CompactFlash 
card. These functions require that an optional hard disk kit be 
installed.
A hard disk kit and a CF adapter cannot be installed...

CompactFlash 312
1Turn off the machine and discon-
nect the power cord and inter-
face cables.
2Remove the rear cover.
3Using a screwdriver, loosen the 
screw.
Do not remove any screw 
other than the one indicated 
in the illustration.
Downloaded From ManualsPrinter.com Manuals 

CompactFlash 313
4Open the inside cover.
5Plug the cable on the CF 
adapter into the connector on 
the controller board.
6Insert the three mounting pins 
on the CF adapter into the holes 
in the controller board to mount 
the CF adapter onto the control-
ler board.
Downloaded From ManualsPrinter.com Manuals 

CompactFlash 314
7Fully insert the CompactFlash 
card into the appropriate slot. 
When the CompactFlash card is 
correctly inserted, the button on 
the top side of the slot (circled in 
the illustration) slightly pops out.
Before removing the 
CompactFlash card, 
press in this button.
8Close the inside cover, and then tighten the screw.
9Close the rear cover.
10Reconnect all interface cables.
11Reconnect the power cord, and 
turn on the machine.
12Declare the Memory card in the Windows printer driver...

Tray 3 (Lower Feeder Unit) 315
Tray 3 (Lower Feeder Unit)
You can install up to one optional lower feeder unit (Tray 3). The lower feeder 
unit increases your machine’s media feed capacity by 500 sheets. 
Kit Contents
„Lower feeder unit with a tray (500-sheet capacity)
Downloaded From ManualsPrinter.com Manuals 

Tray 3 (Lower Feeder Unit) 316
Installing Tray 3
Note
Since consumables are installed in the machine, be sure to keep the 
machine level when moving it in order to prevent accidental spills.
1Turn off the machine and discon-
nect the power cord and inter-
face cables.
2Prepare the lower feeder unit.
Be sure to place the lower feeder unit on a level surface.
3Open the right side cover of the 
lower feeder unit.
The right side cover of the lower feeder must be opened before the 
feeder can be installed...