Konica Minolta magicolor 4695MF User Manual

Status, Error, and Service Messages 297
Trans. Roll. LifeThe time to replace 
the transfer roller 
has been reached.Replace the transfer 
roller.
TRAYx OPEN
CLOSE TRAYxThe indicated paper 
tray is open.Close the indicated 
paper tray.
UNABLE TO
COLLATE JOBSince the hard disk 
(area for saving 
copies when print-
ing sets) is full, cop-
ies cannot be 
printed as sets.Print only one set at a 
time, or reduce the 
number of pages to be 
printed.
USB Dev. Not supportA USB device 
incompatible with 
this...

Status, Error, and Service Messages 298
Wrong I-Unit xAn imaging unit 
incompatible with 
the machine is 
installed.Replace the indicated 
imaging unit with a cor-
rect one.
WRONG PASSWORD
xxxThe password is 
incorrect, so the 
indicated server 
could not be 
accessed.Check the password, 
and then specify the 
correct one.
Wrong Toner xA toner cartridge 
incompatible with 
the machine is 
installed.Replace the indicated 
toner cartridge with a 
correct one.
xxx IS DISABLEDThe TCP/IP, FTP, 
SMTP or SMB...

Status, Error, and Service Messages 299 Service Messages
These messages indicate a more serious fault that can only be corrected by a 
customer service engineer. If one of these messages appears, turn the 
machine off, then turn it on again. If the problem persists, contact your local 
vendor or authorized service provider.
This service message... means... Do this...
MACHINE TROUBLE
SERVICE CALL (xxxx)An error has been 
detected with the item 
indicated “
xxxx” in 
the service message.Reboot the machine....

Status, Error, and Service Messages 300
Downloaded From ManualsPrinter.com Manuals 

12
12Installing
Accessories
Downloaded From ManualsPrinter.com Manuals 

Introduction 302
Introduction
Note
Any damage to the machine caused by the use of accessories not 
manufactured or supported by KONICA MINOLTA will void your 
warranty. 
This chapter provides information about the following accessories.
Note
The hard disk kit and CF adapter cannot be installed to be used at the 
same time. 
Installing accessories always requires that the machine and 
accessories are turned off and unplugged during installation.
For details on the available options, refer to...

Antistatic Protection 303
Antistatic Protection
Note
It’s very important to protect the printer controller board from 
electrostatic damage while performing any task involving the controller 
board.
Turn off all power switches first. If an antistatic wrist strap is provided in 
your printer option kit, attach one end of it to your wrist and the other 
end to the bare metal chassis on the back of your printer. Never attach 
the wrist strap to any piece of equipment with an electrical current 
present....

Dual In-Line Memory Module (DIMM) 304
Dual In-Line Memory Module (DIMM)
You may need additional memory (DIMM) for complex graphics and 
for duplex (double-sided) printing.
This machine detects only half of the amount of the installed memory.
Dual in-line memory module (or DIMM) is compact circuit board with 
surface-mount memory chips.
There is 256 MB of onboard memory and one available memory 
expansion slot. The memory can be expanded to a maximum of 
768 MB (256 MB + 512MB).
Installing a DIMM
Note...

Dual In-Line Memory Module (DIMM) 305
2Remove the rear cover.
3Using a screwdriver, loosen the 
screw.
Do not remove any screw 
other than the one 
indicated in the 
illustration.
4Open the inside cover.
Downloaded From ManualsPrinter.com Manuals 

Dual In-Line Memory Module (DIMM) 306
5Insert the new DIMM straight 
into the DIMM connector until 
the latches snap into the locked 
position.
Observe the keyed side of the 
DIMM to align it with the connec-
tor. If you cannot snap the DIMM 
into place, do not force it. Repo-
sition it, making sure that the 
DIMM is seated completely in 
the connector.
6Close the inside cover, and then tighten the screw.
7Close the rear cover.
8Reconnect all interface cables.
9Reconnect the power cord, and 
turn on the...