Konica Minolta bizhub C652 User Manual

							bizhub C652/C652DS/C552/C552DS/C45210-6
10.1 Using an authentication unit (biometric type)10
5Press [Edit].
6Place your finger on the authentication unit to scan the finger vein pattern.
%Scan the finger vein pattern three times; reset the same finger each time and then press [Scan] for 
each scanning.
%After scanning the finger vein pattern, place the same finger on the authentication unit, and press 
[Authentication Test].
%If your finger vein patterns have been authenticated in the authentication test, press [New]. If 
authentication has failed, retry scanning the finger.
7Press [Close] twice.
8Enter the user name and password.
9Configure function permission settings as required.
10Press [OK].
11Press [Close].
Registering a user using Data Administrator
To use Data Administrator, configure this machine, and set up Data Administrator. For setup, install the 
BioDriver (USB-Driver) of the authentication unit, and then install Data Administrator Bio Plugin.
NOTICE
Before setup, install Data Administrator V4.0 or later in your computer. For the Data Administrator operating 
environment and installation procedure, refer to the Data Administrator Users Guide.
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C45210-7
10.1 Using an authentication unit (biometric type)10
Checking the version of the installed Data Administrator
1From the Help menu of Data Administrator, select Version Information.
NOTICE
This software cannot be used if the version is 3.x. Install 4.x.
If Data Administrator V3.x is installed, it is removed when V4.x is installed.
2Click the [Plug-in version].
3In Plug-in information list:, confirm the plugin version of Data Administrator.
%This software is available if the plugin version is 4.x.
Setup
1Turn the main power of this machine off, and disconnect the authentication unit from this machine.
2Install BioDriver (USB-Driver).
Connect the authentication unit to the USB port of your computer.
The Found New Hardware dialog box appears.
3Select Locate and install driver software (recommended).
4Insert the application CD-ROM provided with the authentication unit into the CD-ROM drive of the 
computer.
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C45210-8
10.1 Using an authentication unit (biometric type)10
5Click the Browse my computer for driver software (advanced).
6Check that the drivers search location is the application CD-ROM, and then click the [Next].
%When the drivers search location is not the application CD-ROM, click the [Browse]. Select the 
BioDriver (USB-Driver) folder on the CD-ROM, and then click the [OK].
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C45210-9
10.1 Using an authentication unit (biometric type)10
%Installation starts.
7Click the [Close].
Installation of BioDriver (USB-Driver) is completed.
8Install Data Administrator Bio Plugin.
Open the DA_Bio_Plugin folder on the application CD-ROM, and then click setup.exe.
9Select a language, and then click the [OK].
The installation program starts.
10Follow the on-screen instructions to proceed with the installation.
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C452 10-10
10.1 Using an authentication unit (biometric type)10
11Click the [Next].
12Select I accept the terms in the license agreement, and then click the [Next].
13Click the [Install].
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C452 10-11
10.1 Using an authentication unit (biometric type)10
14Click the [Finish].
Installation of the Data Administrator Bio Plugin is completed, which completes the setup.
User registration
To register a user with Data Administrator, connect the authentication unit to the USB port of the computer, 
and also connect the computer to this machine via network.
1If the authentication unit is already connected to this machine, turn the main power switch of this 
machine off, and then disconnect the authentication unit.
%When the authentication unit is already connected to the computer, go to step 4.
NOTICE
To turn the main power switch off and on, first turn the main power switch off, and then turn it on after 
10 or more seconds has elapsed. Not doing so may result in an operation failure.
When connecting or disconnecting the USB cable, hold the plug. Otherwise, the cable may be 
damaged.
2Turn the main power on.
3Connect the authentication unit to the USB port of the computer that contains Data Administrator.
NOTICE
Do not connect another USB device to the same port as for the authentication unit. Doing so reduces 
the USB power supply, resulting in an operation failure.
To use the USB hub, be sure to connect the self-power USB hub that supplies 500 mA or more.
Restart the procedure 5 or more seconds after connecting the authentication unit.
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C452 10-12
10.1 Using an authentication unit (biometric type)10
4Data Administrator starts, and device information of this machine is imported.
The Device Information window appears.
%For details on how to import device information, refer to the Data Administrator Users Guide.
5In Select Function, select Authentication Settings - User Setting, and then click the [Add].
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C452 10-13
10.1 Using an authentication unit (biometric type)10
6Select the desired template, and then click the [OK].
The User Registration window appears.
7Enter the user name and password, select the AU-101 or AU-102 tab, and then click the [Register 
Auth. Info].
%Enter the E-mail address and other information as required.
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C452 10-14
10.1 Using an authentication unit (biometric type)10
8Register finger vein pattern.
%Scan the finger vein patterns three times; reset the same finger and then press [Start Reading] for 
each scanning.
%After scanning the finger vein patterns, place the same finger, and click [Authentication Test].
%If the authentication test has succeeded, press [Register].
%If the authentication test has failed, place your finger on the authentication unit again, and click 
[Authentication Test].
%If the authentication has failed, click [Reset] to repeat the scanning process.
For authentication unit AU-101
For authentication unit AU-102
9Click the [Registration].
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C452 10-15
10.1 Using an authentication unit (biometric type)10
10Click the [OK].
%Repeat steps 5 to 10 to register all users.
11Click the [Export to the device].
%Select the user name and click the [Edit] to change the registered data.
Downloaded From ManualsPrinter.com Manuals