Konica Minolta bizhub C652 User Manual

							bizhub C652/C652DS/C552/C552DS/C4527-3
7.1 System Settings7
7.1 System Settings
Configure the basic functions of this machine.
7.1.1 Power Save Settings
Configure the settings for the power-saving mode.
%Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Power Save 
Settings].
Settings
Low Power Mode Settings Enter a time period before switching to the lower power mode when this 
machine is not being operated.
Sleep Mode Settings Enter a time period before switching to the sleep mode when this machine 
is not being operated.
Power Save Key Configure the type of the power save function to be started when you press 
the [Power Save] key.
Low Power Provides power-saving effect higher than normal.
Sleep Although this machine conserves more energy in 
the sleep mode than in the power save mode, the 
machine must warm-up when the sleep mode is 
canceled, therefore taking more preparation time 
than the power save mode.
Enter Power Save Mode Configure settings for switching to the power save mode after printing doc-
uments from computers or receiving faxes.
Normal Enters the power save mode when the time spec-
ified in Low Power Mode Settings has elapsed.
Immediately Enters the power save mode in a short time.
Factory default
Low Power Mode Settings 15 minutes
Sleep Mode Settings 30 minutes
Power Save Key Lower
Enter Power Save Mode Immediately
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4527-4
7.1 System Settings7
7.1.2 Output Settings
Configure the settings for the output functions.
%Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Output Settings]. 
Settings
Print/Fax Output Settings This setting is for the print and fax operations. For details, refer to the Us-
ers Guide [Network Scan/Fax/Network Fax Operations] and  Users 
Guide [Print Operations].
Output Tray Settings Configure an output tray given priority for outputting by function.
This item is displayed when the Finisher or Job Separator JS-504 is in-
stalled.
Shift Output Each Job Select whether to shift the output paper for each job.
This item is displayed when the Finisher or Job Separator JS-504 is in-
stalled.
Factory default
Print/Fax Output Settings Print: Page Print
Fax: Batch Print
Output Tray Settings • Copy: Tray 2
• Print: Tray 2
• Print Reports: Tray 1
• Fax: Tray 1
[Tray 3] is displayed when the Job Separator JS-603 is installed in the Fin-
isher FS-527.
Shift Output Each Job Yes
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4527-5
7.1 System Settings7
7.1.3 Date/Time Settings
Configure the current date and time and the time zone.
%Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Date/Time Settings].
dReference
To cancel the current settings:
Press the [C] key.
Settings
Year Configure the current date and time.
Monthly
Daily
Hour
Minute
Time Zone Configure the UTC (Coordinate Universal Time) related time zone.
Factory default
Time Zone +00:00
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4527-6
7.1 System Settings7
7.1.4 Daylight Saving Time
Configure daylight saving time settings.
0This function is available when this machine is connected to the network where UTC (Coordinate 
Universal Time) is specified. For details, refer to the Users Guide [Network Administrator].
%Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Daylight Saving 
Time].
Settings
Configure whether to use daylight saving time and the time difference from UTC (Coordinate Universal 
Time).
Factory default
Daylight Saving Time No
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4527-7
7.1 System Settings7
7.1.5 Weekly Timer Setting
Configure the weekly timer in order to allow you to turn on and off this machine at the specified date and time.
0An exact date/time setting must be performed in advance. 
%Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Weekly Timer 
Settings].
Settings
Weekly Timer ON/OFF Set-
tingsConfigure whether to use the weekly timer function.
Time Settings Configure the time of each day of the week to turn on and off this machine.
Set  All The setting for the selected day of the week is ap-
plied to the same day of the week in other weeks.
Delete Cancels the selected input value.
Date Settings Configure the days when timer operation is activated individually. To can-
cel the setting, press the same day again.
Daily Setting Configure the days of the week when the timer 
operation is activated.
Select Time for Power 
SaveConfigure the time to turn this machine off and on if you want to turn it off 
at a specific time, for example, during a lunch break.
Password for Non- Busi-
ness HoursConfigure whether to require a user to enter the password if the user uses 
this machine outside the specified time.
• To make the user to enter the password, you need to specify the pass-
word.
Factory default
Weekly Timer ON/OFF Set-
tingsOFF
Select Time for Power 
SaveNo
Password for Non-Busi-
ness HoursNo
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4527-8
7.1 System Settings7
7.1.6 Restrict User Access
Restrict the machine operation, or change or delete the copy programs by the user.
%Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Restrict User 
Access].
Settings
Copy Program Lock Set-
tingsConfigure the registered copy programs that are prevented from being 
changed or deleted.
Delete Saved Copy Pro-
gramDelete the registered copy programs.
Restrict Access to Job Set-
tingsConfigure whether to allow users to configure the following settings.
Changing Job Priority Configure whether to allow users to change the 
print priority of jobs.
Delete Other User 
JobsConfigure whether to allow other users to delete 
jobs when the user authentication settings have 
been specified.
Registering and 
Changing AddressesThis setting is for the network scan, fax, and net-
work fax operations.
For details, refer to the Users Guide [Network 
Scan/Fax/Network Fax Operations].
Changing Zoom Ra-
tioConfigure whether to allow users to change reg-
istered zoom ratios.
Changing the From 
AddressThis setting is for the network scan operations.
For details, refer to the Users Guide [Network 
Scan/Fax/Network Fax Operations].
Change Registered 
OverlayConfigure whether to allow users to change reg-
istered image overlays.
Biometric/IC Card In-
fo. RegistrationConfigure whether to allow a registered user to 
register or delete biometric authentication infor-
mation or IC card authentication information of 
the user.
Restrict Operation Restrict Broadcast-
ingThis setting is for the network scan, fax, and net-
work fax operations.
For details, refer to the Users Guide [Network 
Scan/Fax/Network Fax Operations].
Factory default
Changing Job Priority Allow
Delete Other User Jobs Restrict
Registering and Changing 
AddressesAllow
Changing Zoom Ratio Allow
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4527-9
7.1 System Settings7
7.1.7 Expert Adjustment
Make adjustments so that output quality is increased.
%Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment]. Changing the From Ad-
dressRestrict
Change Registered Over-
layAllow
Biometric/IC card Informa-
tion RegistrationRestrict
Restrict Broadcasting OFF Factory default
Settings
AE Level Adjustment Configure the initial value for AE (auto exposure). The higher the setting, 
the more that the original background is emphasized.
Printer Adjustment Adjust the starting print position and defective print images caused by pa-
per type features.
dReference
The starting print position is factory-adjusted. Normally, you 
are not required to change the set values.
Leading Edge Adjustment p. 7-13
Centering p. 7-13
Leading Edge Adjustment (Du-
plex Side 2)p. 7-13
Centering (Duplex 2nd Side) p. 7-13
Erase Leading Edge Adjust leading edge erase width.
For details on displaying this item, 
contact your service representative.
Vertical  Adjustment Adjust the feed direction zoom ratio of 
paper types.
For details on displaying this item, 
contact your service representative.
Media Adjustment p. 7-14
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4527-10
7.1 System Settings7
Finisher Adjustment Adjust the staple, folding, and punch position of the finisher.
This button appears only when the finisher is installed.
dReference
Create a sample in advance, and then adjust them while 
checking the sample.
Center Staple Position p. 7-14
Half-Fold Position p. 7-15
Tri-Fold Position Adjustment p. 7-15
(This item is displayed when the Fin-
isher FS-526 and Saddle Stitcher SD-
508 are installed.)
Punch Vertical Position Adjust-
mentp. 7-16
(This item is displayed when the Fin-
isher FS-526 and Punch Kit PK-516 
are installed.)
Punch Horizontal Position Ad-
justmentp. 7-16
Punch Regist Loop Size Adjust-
mentp. 7-17
Punch Edge Sensor Adjustment p. 7-17
(This item is displayed when the Fin-
isher FS-526 and Punch Kit PK-516 
are installed.)
Vertical Punch (Z-Fold) Position 
Adjustmentp. 7-17
(This item is displayed when Z Folding 
Unit is installed.)
Horizontal Punch (Z-Fold) Posi-
tion Adjustmentp. 7-18
(This item is displayed when Z Folding 
Unit is installed.)
1st Z-Fold Position Adjustment p. 7-18
(This item is displayed when Z Folding 
Unit is installed.)
2nd Z-Fold Position Adjustment p. 7-19
(This item is displayed when Z Folding 
Unit is installed.)
Punch Unit Size Detect Sensor p. 7-19
(This item is displayed when Z Folding 
Unit is installed.)
Post Inserter Tray Size Adjust-
ment Adjust the paper size to be used in the 
Post Inserter. You can specify differ-
ent paper sizes for the upper and low-
er trays. This button appears when the 
Post Inserter PI-505 is installed.
Density Adjustment Correct the toner amount to be used by color depending on the paper 
type.
• To correct the toner amount to be used in the black print mode, press 
[Black Image Density].
Image Stabilization Image Stabilization OnlyPress the [Start] key to stabilize imag-
es.
Pressing the [Image Stabilization Only] 
button executes normal image stabili-
zation.
If a good result was not achieved after 
the [Image Stabilization Only] button 
was pressed, execute [Initialize + Im-
age Stabilization]. Settings
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4527-11
7.1 System Settings7
Image Stabilization Setting Specify the type and opportunity of 
image stabilization. If [Standard] is se-
lected, normal stabilization is per-
formed during warm-up processing 
when a change in the absolute humid-
ity has been detected during warm-up 
processing.
If [Color Priority] is selected, color sta-
bilization is performed when the pow-
er has been turned on.
Selecting [Black & White  Priority] exe-
cutes monochrome stabilization dur-
ing warm-up when absolute humidity 
change is detected during the warm-
up, and then stabilizes color before 
performing color print.
Paper Separation Adjust-
mentAdjust the paper position where the two sides are separated for 2-sided 
print.
Color Registration Adjust Correct color shifts if they are detected in the print result.
For details, refer to page 7-20.
Gradation Adjustment Adjust irregular gradation levels of print images.
For details, refer to page 7-21.
Image Stabilization Only Stabilize the image by pressing the 
[Start] key before performing grada-
tion adjustment.
Print Adjust the gradation when the color 
gradation has been changed in a print 
image. This function performs adjust-
ment, emphasizing the gradation ex-
pression of an image and the 
reproducibility of texts or lines.
Copy Adjust the gradation when the color 
gradation has been changed in a print 
image. This function performs adjust-
ment to save as many images as pos-
sible in memory.
Scanner Area Adjust the scan range of the scanner.
For details on displaying this item, contact your service representative.
ADF Adjustment Make adjustments for scanning images in the ADF.
For details on displaying this item, contact your service representative.
Line Detection Prior Detection Setting
(bizhub C652/C552/C452)Configure whether to issue an alert 
when the slit glass is dirty.
• Select an alert display format and 
contamination detection level.
Prior Detection Setting (front)
(bizhub C652DS/C552DS)Configure whether to issue an alert 
when the slit glass (front) is dirty.
• Select an alert display format and 
contamination detection level.
Prior Detection Setting (back)
(bizhub C652DS/C552DS)Configure whether to issue an alert 
when the slit glass (back) is dirty.
• Select an alert display format, con-
tamination detection level and dis-
play timing.
Feed Cleaning Settings Configure whether to remove a dirt on 
the slit glass each time one sheet of 
paper passes through the ADF when 
scanning an original using the ADF.
Trail Edge Adjust Correct a shift if it is detected at the trailing edge of the print result.
Place, 11 e 17 w, 8-1/2 e 11 v, A3 w, or A4 v on the bypass tray, and 
then press the [Start] key to print a test pattern. Settings
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4527-12
7.1 System Settings7
User Paper Settings Configure special paper settings for User Paper 1 through 6. Settings to 
configure include Basic Weight and Media Adjustment.
For details on displaying this item, contact your service representative.
Erase Adjustment Non-Image Area Erase Opera-
tion SettingsConfigure Non-Image Area operation 
settings.
[Auto]: 
Automatically detects the background 
density of the original, and selects ei-
ther Bevel or Rectangular accord-
ingly.
[Specify]: 
Allows you to manually specify an 
erase method and original density. As 
an erase method, select Bevel or 
Rectangular. Specify an original 
density from five levels.
Factory default
AE Level Adjustment Standard (2)
Leading Edge Adjustment 0.0 mm
Centering 0.0 mm
Leading Edge Adjustment 
(Duplex Side 2)0.0 mm
Centering (Duplex 2nd 
Side)0.0 mm
Media Adjustment Auto
Center Staple Position 0.0 mm
Half-Fold Position 0.0 mm
Tri-Fold Position Adjust-
ment0.0 mm
Punch Vertical Position Ad-
justment0.0 mm
Punch Horizontal Position 
Adjustment0.0 mm
Punch Regist Loop Size 
AdjustmentFor Finisher FS-526
Finisher: 0.0 mm
Finisher (for Z folding): 0.0 mm
Post inserter feeder (Upper tray): 0.0 mm
Post inserter feeder (Lower tray): 0.0 mm
For Finisher FS-527: 0
Vertical Punch (Z-Fold) Po-
sition Adjustment0.0 mm
Horizontal Punch (Z-Fold) 
Position Adjustment0.0 mm
1st Z-Fold Position Adjust-
ment0.0 mm
2nd Z-Fold Position Ad-
justment0.0 mm
Post Inserter Tray Size Ad-
justmentAuto Detect
Density Adjustment 0
Image Stabilization Only Image Stabilization Only
Image Stabilization Setting Standard
Paper Separation Adjust-
ment0.0 mm Settings
Downloaded From ManualsPrinter.com Manuals