Konica Minolta bizhub C652 User Manual

							bizhub C652/C652DS/C552/C552DS/C4529-10
9.2 Troubleshooting table9
Icons that appear in the touch-panel screen
Now Downloading Program 
Data from the Firmware server.(1) CS Remote Care was activat-
ed by your service representa-
tive.
(2) Internet ISW is being down-
loaded.Do not turn off the sub power 
switch while this message is dis-
played.
After turning off the sub power 
switch, turn off the main power 
switch, and then contact your 
service representative.
Authentication information en-
tered is invalid, due to failed ac-
cess attempts. 
Contact the administrator.The authentication information 
has become invalid since the au-
thentication attempts have failed 
the specified number of times.Contact the administrator of the 
machine.
Due to failed access attempts, 
the current administrator pass-
word is invalid.The administrator password has 
become invalid since the authen-
tication attempts have failed the 
specified number of times.Turn the machine off, then on 
again.
Turn off the main power switch, 
and then wait at least 10 sec-
onds before turning it on again.
The job log has reached the 
maximum allowed.
Contact the administrator.The write area of the job log has 
reached the maximum allowed.Obtain the job log using Page-
Scope Web Connection.
No Animation Guide data availa-
ble. Contact your administrator.Animation guide data is not in-
stalled.For details on installing anima-
tion guide data, contact your 
service representative.
Verify that external keyboard is 
properly connected. It may not 
be connected or multiple key-
boards may be connected.The compact keyboard is not 
connected to this machine.Turn off the main power of this 
machine, connect the compact 
keyboard to this machine. Wait 
at least 10 seconds, and then 
turn on the main power of this 
machine. Message Cause Remedy
Icon Description
Indicates that data is being sent from the machine, regardless of the cur-
rent mode.
Indicates that the machine is receiving data, regardless of the current 
mode.
Indicates that an error occurred during an image stabilization operation, a 
print operation or a scan operation.
Press this icon to view a screen containing a warning code.
If the warning screen was closed when a warning occurred, press this but-
ton to display the warning screen again.
Appears when there is a message indicating that consumables must be re-
placed or the machine requires maintenance. Press this button to display 
the message, and then carry out the replacement or maintenance proce-
dure.
Appears when an error occurs with the connection to the POP server.
Indicates that paper is not loaded in the paper tray.
Indicates that very little paper remains in the paper tray.
If the optional image controller is installed, press this icon to display the 
setting screen for the image controller.
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4529-11
9.2 Troubleshooting table9
Indicates that Enhanced Security Mode is set to ON.
Appears when the external memory (USB memory) is not connected.
Indicates that a nonstandard external memory has been connected to this 
machine, therefore, USB connection is not enabled.
Indicates that the job is in the waiting-for-redial status because, for exam-
ple, the recipients line is busy when sending with the G3 Fax or IP Address 
Fax function. Icon Description
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4529-12
9.3 If print quality is deteriorated9
9.3 If print quality is deteriorated
Cleaning the electrostatic charger wire
If the electrostatic charger wire is dirty, streaks will appear though the printed images. If this occurs, follow 
the procedure described below to clean the electrostatic charger wire.
0When replacing the waste toner box, follow the Quick Guide to clean the electrostatic charger wire.
1Open the machines lower front door.
2Slowly pull out the charger-cleaning tool as far as possible. Next, 
slowly push in the charger-cleaning tool as far as possible.
Repeat the above operations three times.
3Securely insert the charger-cleaning tool, and then close the front door.
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4529-13
9.3 If print quality is deteriorated9
Cleaning the print head
If the print head becomes dirty, print quality may be reduced. If this occurs, clean the print head according 
to the following procedure.
1Pull out tray 1.
2Remove the print head glass cleaning tool from tray 1.
3Open the machines lower front door.
4Release the securing levers for the waste toner box, and then 
remove the waste toner box.
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C4529-14
9.3 If print quality is deteriorated9
5Insert the print head glass cleaning tool into the print head 
cleaning opening, pull it out, and then repeat this back-and-forth 
movement two or three times.
6Install the waste toner box.
7Place back the print head glass cleaning tool to tray 1.
8Close tray 1.
Downloaded From ManualsPrinter.com Manuals 
						

							10Authentication unit (biometric 
type)
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C45210-2
10.1 Using an authentication unit (biometric type)10
10 Authentication unit (biometric type)
This chapter describes the authentication unit (biometric type).
1. Authentication unit (biometric type) AU-101
2. Authentication unit (biometric type) AU-102
10.1 Using an authentication unit (biometric type)
The authentication unit (biometric type) is a biometrics (biometric authentication) system that scans a finger 
vein pattern to perform personal authentication. Using the biometric authentication, you can log in to this 
machine where user authentication settings are configured in order to execute a print job.
Place your forefinger straight so that your forefinger cushion slightly touches the hollow and protuberance 
part of the scanning section. Secure your middle finger and thumb on the both sides of the authentication 
unit to prevent your forefinger to be used for authentication from rotating.
For details on how to place your forefinger on the authentication unit, refer to page 10-17.
NOTICE
If you change the authentication unit from AU-101 to AU-102, the users you registered with AU-101 cannot 
use AU-102. Connect AU-102 to this machine, and then register the users again.
Do not place anything other than your finger on the scanning section during scanning operation. Doing so 
may cause a malfunction.
Do not disconnect the USB cable from the authentication unit or computer during a scanning operation. 
Doing so may cause the system to become unstable.
The status indicator LED and notice sound indicate the status of the authentication unit.
*1For authentication unit (biometric type) AU-101
*2For authentication unit (biometric type) AU-102
1
2
Status indicator LEDs Status
Lit in green Ready state or authentication is completed
Flash in green During authentication or scanning operation
Lit in red Authentication failed or scanning failed
Unlit The authentication unit is not recognized
Notice sound Status
One short blip sound Scanning starts
One short blip sound During a retry after authentication failed
One short blip sound
*1/two short blip sounds*2Authentication completed
Two short blip sounds
*1/
one short blip and one long beep sounds*2Authentication failed
One long beep sound
*2Scanning canceled
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C45210-3
10.1 Using an authentication unit (biometric type)10
To use the authentication unit, first register the finger vein pattern of the user in this machine. The registered 
user, who is authenticated with the finger vein pattern, can log in to this machine or execute a print job. This 
section explains how to configure the required settings in this machine, register users, and log in with 
authentication.
10.1.1 Configuring this machine
NOTICE
User authentication settings must be configured with MFP authentication on this machine.
This device does not support external server authentication. To combine account track settings with user 
authentication settings, set Synchronize User Authentication & Account Track to Synchronize. 
1Use the control panel of this machine to display the Administrator Settings screen. Press [4 User 
Authentication/Account Track], then [1 General Settings].
2Set [User Authentication] to ON (MFP), and then press [OK].
3Press [Yes], and then [OK].
4Press [8 Authentication Device Settings].
5Press [1 General Settings].
6Press [Bio Authentication].
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C45210-4
10.1 Using an authentication unit (biometric type)10
7Configure Beep Sound and Operation Settings.
%For Beep Sound, specify whether to give a blip sound when the finger vein pattern is scanned 
successfully.
%For Operation Settings, specify how to log in to this machine after registration.
1-to-many authentication: Allows the user to log in by simply placing his or her finger.
1-to-1 authentication: Allows the user to log in by entering the user name and placing his or her 
finger.
For details on how to log in to this machine, refer to page 10-17.
8Press [OK] twice.
9Press [2 Logoff Settings].
10Specify whether to log out the user when scanning the original has finished after the user logged in with 
the authentication unit.
11Press [OK].
12Press [Close] twice.
Downloaded From ManualsPrinter.com Manuals 
						

							bizhub C652/C652DS/C552/C552DS/C45210-5
10.1 Using an authentication unit (biometric type)10
10.1.2 Registering a user
The following two methods can be used to register a user.
-Connect the authentication unit to this machine, and directly register the target user in this machine
-Connect the authentication unit to your computer, and use Data Administrator to register the target user
NOTICE
The registered user data is saved in the HDD of this machine. Changing the user authentication type of this 
machine or formatting the HDD will erase the registered user data.
Registering a user using the control panel of this machine
1Use the control panel of this machine to display the Administrator Settings screen. Press [4 User 
Authentication/Account Track], and then [2 User Authentication Settings].
NOTICE
[2 User Authentication Settings] is disabled when User Authentication is set to [OFF] in General 
Settings.
2Press [2 User Registration].
3Select a desired registration number, and then press [Edit].
4Press [Register Auth. Info.].
Downloaded From ManualsPrinter.com Manuals