Konica Minolta bizhub C35P User Manual

							Status, Error, and Service Messages 9-46
Downloaded From ManualsPrinter.com Manuals 
						

							10
Installing
Accessories
Downloaded From ManualsPrinter.com Manuals 
						

							Introduction 10-2
Introduction
Note
Use of accessories not manufactured or supported by 
KONICA MINOLTA will void your warranty.
For details of accessories, visit our web site (http://printer.konicam-
inolta.com)
Note
The hard disk kit HD-P03 and CF Adapter MK-725 cannot be installed to 
be used at the same time. 
Installing accessories always requires that the printer and accessories 
are turned off and unplugged during installation.Dual In-Line 
Memory Module 
(DIMM)512 MB DIMM
Lower Feeder Unit 
PF-P09(Tray 3)500-sheet tray included
Hard Disk Kit 
HD-P03SATA Hard Disk
CF Adapter MK-725Adapter for CompactFlash card
CompactFlash 1 GB, 2 GB, 4 GB, 8 GB
Downloaded From ManualsPrinter.com Manuals 
						

							Antistatic Protection10-3
Antistatic Protection
Note
It’s very important to protect the printer controller board from 
electrostatic damage while performing any task involving the controller 
board.
Turn off all power switches first. If an antistatic wrist strap is provided in 
your printer option kit, attach one end of it to your wrist and the other 
end to the bare metal chassis on the back of your printer. Never attach 
the wrist strap to any piece of equipment with an electrical current 
present. Plastic, rubber, wood, painted metal surfaces, and telephones 
are not acceptable grounding points.
If you don’t have an antistatic wrist strap, discharge your body’s static 
electric charge by touching a grounded surface before you handle any 
printer boards or components. Also avoid walking around after 
grounding yourself.
Downloaded From ManualsPrinter.com Manuals 
						

							Dual In-Line Memory Module (DIMM) 10-4
Dual In-Line Memory Module (DIMM)
You may need additional memory (DIMM) for complex graphics and 
for duplex (double-sided) printing. 
Dual in-line memory module (or DIMM) is compact circuit board with sur-
face-mount memory chips.
There is 256 MB of onboard memory and one available memory expansion 
slot. The memory can be expanded to a maximum of 768 MB (256 MB + 512 
MB).
Installing a DIMM
Note
It’s very important to protect the printer controller board and any 
associated circuit boards from electrostatic damage. Before performing 
this procedure, review the antistatic caution on page 10-3. In addition, 
always handle circuit boards by the edges only.
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
2Using a screwdriver, remove the 
back cover.
Downloaded From ManualsPrinter.com Manuals 
						

							Dual In-Line Memory Module (DIMM)10-5
3Using a screwdriver, remove two 
screws.
4Slide the panel slightly to the 
down and lift it off the printer.
5Insert the DIMM at an angle 
(about 45°) into the connector, 
making sure that the notch on 
the unit aligns with the tab on 
connector, and then press down 
carefully until it clicks into place.
Be sure to handle the 
DIMM by the edges only.
You will hear a click when 
the DIMM is properly 
placed.
6Reinstall the panel and tighten two screws.
7Attach the back cover and tighten four screws.
8Reconnect all interface cables.
Downloaded From ManualsPrinter.com Manuals 
						

							Dual In-Line Memory Module (DIMM) 10-6
9Reconnect the power cord, and 
turn on the printer.
10Declare the additional Printer Memory in the Windows printer driver 
(Properties/Configure tab).
11Print a configuration page (PRINT MENU/CONFIGURATION PG) and 
verify that the total amount of the RAM installed in your printer is listed.
Downloaded From ManualsPrinter.com Manuals 
						

							Hard Disk Kit HD-P0310-7
Hard Disk Kit HD-P03
If you install a Hard Disk Kit HD-P03, the followings can be performed:
–Collate printing
–Job printing/saving
–Fonts/forms download
–User Authentication/Account Track
–Direct printing
–XPS printing
A hard disk kit HD-P03 and a CF Adapter MK-725 cannot be installed 
simultaneously.
Installing the Hard Disk Kit HD-P03
Note
It’s very important to protect the printer controller board and any 
associated circuit boards from electrostatic damage. Before performing 
this procedure, review the antistatic caution on page 10-3. In addition, 
always handle circuit boards by the edges only.
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
Downloaded From ManualsPrinter.com Manuals 
						

							Hard Disk Kit HD-P03 10-8
2Using a screwdriver, remove the 
back cover.
3Using a screwdriver, remove two 
screws. 
4Slide the panel slightly to the 
down and lift it off the printer.
Downloaded From ManualsPrinter.com Manuals 
						

							Hard Disk Kit HD-P0310-9
5Attach the two cables to the hard 
disk kit.
6Insert the hard disk kit mounting 
pins.
7Plug the two cables on the hard 
disk kit into the connector.
8Reinstall the panel and tighten two screws.
9Attach the back cover and tighten four screws.
10Reconnect all interface cables.
Downloaded From ManualsPrinter.com Manuals